Revise the content based on the v2 additions. This is kept as a separate
patch to avoid confusing those who have already reviewed the v1 series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Adds information regarding SPL handling the loading and processing of
secured u-boot images as part of the second stage boot the SPL does.
Introduces the description of a new interface script in the TI SECDEV
Package which handles the creation and prep of secured binary images.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If MAC is directly connected to another MAC (like a switch for example)
we don't need to probe for a phy, autoneogation and so on. We simply
have to setup speed.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that platform-specific ACPI global NVS is added, pack it into
ACPI table and get its address fixed up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for standard type SCI (without FIFO) port.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
When building a FIT with external data (-E), U-Boot proper may require
absolute positioning for executing the external firmware. To acheive this
use the (-p) switch, which will replace the amended 'data-offset' with
'data-position' indicating the absolute position of external data.
It is considered an error if the requested absolute position overlaps with the
initial data required for the compact FIT.
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.
The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.
The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.
For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some drivers are still directly accessing the chip->mtd field. Patch
them to use nand_to_mtd() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
nand torture currently works on exactly one nand block which is specified
by giving the byteoffset to the beginning of the block.
Extend this by allowing for a second parameter specifying the byte size
to be tested.
e.g.
==> nand torture 1000000
NAND torture: device 0 offset 0x1000000 size 0x20000 (block size 0x20000)
Passed: 1, failed: 0
==> nand torture 1000000 40000
NAND torture: device 0 offset 0x1000000 size 0x40000 (block size 0x20000)
Passed: 2, failed: 0
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
[scottwood: fix usage to show size as optional, and add misssing braces]
Signed-off-by: Scott Wood <oss@buserror.net>
A reset controller is a hardware module that controls reset signals that
affect other hardware modules or chips.
This patch defines a standard API that connects reset clients (i.e. the
drivers for devices affected by reset signals) to drivers for reset
controllers/providers. Initially, DT is the only supported method for
connecting the two.
The DT binding specification (reset.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/reset/reset.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This updates the device-tree-bindings doc for x86-pinctrl driver:
- clarify "gpio-offset" is required only when "mode-gpio" is set
- correct property name "pull-strength"
- use tab instead of space at several places
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
on the shc board we see when booting in net boot mode,
that the ROM bootloader sends "AM335x ROM" as
vendor-class-identifier. U-Boots doc says "DM814x ROM".
So, add the info to the doc, that there is also
"AM335x ROM" possible.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Tegra186's GPIO controller register layout is significantly different from
previous chips, so add a new driver for it. In fact, there are two
different GPIO controllers in Tegra186 that share a similar register
layout, but very different port mapping. This driver covers both.
The DT binding is already present in the Linux kernel (in linux-next via
the Tegra tree so far).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # v1
Signed-off-by: Tom Warren <twarren@nvidia.com>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
Adds doc/README.ti-secure file to explain in generic terms
how boot images need to be created for secure devices from
Texas Instruments.
Specific details for creating secure boot images for the
AM43xx, DRA7xx and AM57xx secure devices from Texas
Instruments are also provided in the README file.
Secure devices require a security development package (SECDEV)
package that can be downloaded from:
http://www.ti.com/mysecuresoftware
Login is required and access is granted under appropriate NDA
and export control restrictions.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the warning from the Makefile, since boards that do not use generic
board will no longer build. Also update documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.
This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.
The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This will allow a driver's bind function to use the driver data. One
example is the Tegra186 GPIO driver, which instantiates child devices
for each of its GPIO ports, yet supports two different HW instances each
with a different set of ports, and identified by the udevice_id .data
field.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the device tree bindings and the accompanying documentation
for the TI DP83867 Giga bit ethernet phy driver.
The original document was from:
[commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add FIT_FPGA_PROP that user can identify an optional
entry for fpga.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Windows might cache system information and only detect ACPI changes
if you modify the ACPI table versions.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As of now, U-Boot can support installing and booting Ubuntu/Windows
with the help of SeaBIOS. Update the documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Document how to make SeaBIOS load and run the VGA ROM of Intel
IGD device when loaded by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently U-Boot environment address is at offset 0x7fe00 of a 8MB
SPI flash. When creating a partial u-boot.rom image without flash
descriptor and ME firmware, U-Boot actually occupies the last 1MB
of the flash, and reprograming U-Boot causes previous environment
settings get lost which is not convenient during testing.
Adjust the environment address to 0x6ef000 instead (before the MRC
cache data region in the flash).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove ACPI from the TODO list and add a new section to document
current ACPI support in U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This updates the doc for the following places:
- Mention CRB for Bayley Bay
- Mention Congatec QEVAL 2.0 & conga-QA3/E3845
- Limit part of the QEMU paragraphs to 80 cols
- Correct some typos (drive, it's, Ubuntu)
- Add description for "console=ttyS0,115200"
- Remove CONFIG_BOOTDELAY description which is already
in x86-common.h
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default SCI is disabled after power on. ACTL is the register to
enable SCI and route it to PIC/APIC. To support both ACPI in PIC
mode and APIC mode, configure SCI to use IRQ9.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This patch add a compatible spi driver for ath79 series SOC.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add support for ar933x serial.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The getopt(3) optstring '-' is a GNU extension which is not available on BSD
systems like OS X.
Remove this dependency by implementing argument parsing in another way. This
will also change the lately introduced '-b' switch behaviour.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since all the tests are implemented in pytest infrastructure,
So update the dm tests with the same instead of ./test/dm/test-dm.sh
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
The firmware from link [1] only works with U-Boot image that is no
bigger than 328KiB. Using it with the default mainline U-Boot today
which is already around 500KiB is just not working. Correct the link
to be hardkernel_1mb_uboot one [2], so that users can get mainline
U-Boot work out of box.
While at it, the README is updated to include XU4 support, like DTB file
name.
[1] https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel
[2] https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel_1mb_uboot
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This PMIC is connected on SPMI bus so needs SPMI support enabled.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Support SPMI arbiter on Qualcomm Snapdragon devices.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds emulated spmi bus controller with part of
pm8916 pmic on it to sandbox and tests validating SPMI uclass.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Add support for SD/eMMC controller present on some Qualcomm Snapdragon
devices. This controller implements SDHCI 2.0 interface but requires
vendor-specific initialization.
Driver works in PIO mode as ADMA is not supported by U-Boot (yet).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add support for gpio controllers on Qualcomm Snapdragon devices.
This devices are usually called Top Level Mode Multiplexing in
Qualcomm documentation.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add some basic clarification that the dev.key file generated by OpenSSL
contains both the public and private key, and further highlight that
the certificate generated here contains the public key only.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Different sections in the document suggest flattened image tree blob
files have a file name extension of .itb. Fix the list of file extensions
to reflect that.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
- Move most of the flags required into LLVM_RELFLAGS to test at build
time instead of requiring them to be passed in.
- Update doc/README.clang to reflect this
- Switch to rpi_2 as the example as it's closer to working out of the
box than rpi is.
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
It is possible to compile and run the sandbox target with clang
currently, so document that as well.
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now everything is done to load a raw U-Boot proper image instead of
an mkimage-processed one (as far as I tested on NAND, eMMC, NOR).
The SPL already knows the load address of the U-Boot proper without
parsing its uImage header because the load address is defined by
CONFIG_SYS_TEXT_BASE, assuming that the two images are generated from
the same build.
My main motivation of this switch is to use u-boot-with-spl.bin, a
concatenation of u-boot-spl.bin and u-boot.bin. (I wish there were
a concatenation of u-boot-spl.bin and u-boot.img...) Anyway, this
commit would be useful for one-shot image burn.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 3cb9abc9c5 ("ARM: uniphier: update U-Boot file names in
workflow") missed to update these two sentences. Fix them now.
Replace u-boot-spl-dtb.bin and u-boot-dtb.img with u-boot-spl.bin
and u-boot.img, respectively.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds basic support for chromebook_samus. This is the 2015 Pixel and
is based on an Intel broadwell platform.
Supported so far are:
- Serial
- SPI flash
- SDRAM init (with MRC cache)
- SATA
- Video (on the internal LCD panel)
- Keyboard
Various less-visible drivers are provided to make the above work (e.g. PCH,
power control and LPC).
The platform requires various binary blobs which are documented in the
README. The major missing feature is USB3 since the existing U-Boot support
does not work correctly with Intel XHCI controllers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GPIO pins need to be set up on start-up. Add a driver to provide this,
configured from the device tree.
The binding is slightly different from the existing ICH6 binding, since that
is quite verbose. The new binding should be just as extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver which sets up the pin configuration on x86 devices with an ICH6
(or later) Platform Controller Hub.
The driver is not in the pinctrl uclass due to some oddities of the way x86
devices work:
- The GPIO controller is not present in I/O space until it is set up
- This is done by writing a register in the PCH
- The PCH has a driver which itself uses PCI, another driver
- The pinctrl uclass requires that a pinctrl device be available before any
other device can be probed
It would be possible to work around the limitations by:
- Hard-coding the GPIO address rather than reading it from the PCH
- Using special x86 PCI access to set the GPIO address in the PCH
However it is not clear that this is better, since the pin configuration
driver does not actually provide normal pin configuration services - it
simply sets up all the pins statically when probed. While this remains the
case, it seems better to use a syscon uclass instead. This can be probed
whenever it is needed, without any limitations.
Also add an 'invert' property to support inverting the input.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to automate the process of converting code from coreboot a
little. Add a sed script which performs some common transformations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Boting SeaBIOS is done via U-Boot's bootelf command. Document this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To preserve all cover letter knowledge of the status on UEFI payload
support, let's add some sections to README.efi.
Signed-off-by: Alexander Graf <agraf@suse.de>
v3 -> v4:
- Add section about config options
- s/10kb/10KB/
By now the code to only have a single page table level with 64k page
size and 42 bit address space is no longer used by any board in tree,
so we can safely remove it.
To clean up code, move the layerscape mmu code to the new defines,
removing redundant field definitions.
Signed-off-by: Alexander Graf <agraf@suse.de>
One limitation of FIT is that all the data is 'inline' within it, using a
'data' property in each image node. This means that to find out what is in
the FIT it is necessary to scan the entire file. Once loaded it can be
scanned and then the images can be copied to the correct place in memory.
In SPL it can take a significant amount of time to copy images around in
memory. Also loading data that does not end up being used is wasteful. It
would be useful if the FIT were small, acting as a directory, with the
actual data stored elsewhere.
This allows SPL to load the entire FIT, without the images, then load the
images it wants later.
Add a -E option to mkimage to request that it output an 'external' FIT.
Signed-off-by: Simon Glass <sjg@chromium.org>
To make the auto-FIT feature useful we need to be able to provide a list of
device tree files on the command line for mkimage to add into the FIT. Add
support for this feature.
So far there is no support for hashing or verified boot using this method.
For those cases, a .its file must still be provided.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, when generating a FIT, mkimage requires a .its file containing
the structure of the FIT and referring to the images to be included.
Creating the .its file is a separate step that makes it harder to use FIT.
This is not required for creating legacy images.
Often the FIT is pretty standard, consisting of an OS image, some device
tree files and a single configuration. We can handle this case automatically
and avoid needing a .its file at all.
To start with, support automatically generate the FIT using a new '-f auto'
option. Initially this only supports adding a single image (e.g. a linux
kernel) and a single configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
This will be used in mkimage when working out the required size of the FIT
based on the files to be placed into it.
Signed-off-by: Simon Glass <sjg@chromium.org>
I didn't have a common board to enable LVDS.
So add this dcocument to help others who want to enable LVDS in their board.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM expects the boot image (SPL) in the Boot Partition 1.
So, updating images involves the hardware partition switch. It might
be a bit advanced for some users.
To be user-friendly, this commit adds a useful command to update the
images; just put SPL and U-Boot proper into the public directory of
the TFTP server and execute "run emmcupdate" from the command line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This GPIO controller device is used on UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update existing documentation to mention Intel Bayley Bay board
instructions, an additional Bay Trail based board to MinnowMax.
This also adds a minor change to QEMU section to indicate clearly
the instructions are for bare mode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixes typo of pxe_addr_r with pxefile_addr_r.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Since commit ad1ecd2063 ("fdt: Build a U-Boot binary without device
tree") and commit 03c25bcd26 ("fdt: Build an SPL binary without
device tree"), we can use shorter file names for the output images.
The default configuration for UniPhier SoCs enables CONFIG_OF_SEPARATE
and CONFIG_SPL_OF_CONTROL. In this case, spl/u-boot-spl.bin is the
same as spl/u-boot-spl-dtb.bin. Likewise, u-boot.img is the same as
as u-boot-dtb.img. So, this change of the flow has no impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This adds PIC32 UART controller support based on driver model.
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PIC32 clock module consists of multiple oscillators, PLLs, mutiplexers
and dividers capable of supplying clock to various controllers
on or off-chip.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The PCI bus must be enumerated before PCI devices, such as Ethernet
devices, are known to U-Boot. Enhance the distro boot commands to perform
PCI enumeration when needed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, the distro boot commands always enumerate USB devices before
performing network operations. However, depending on the board and end-
user configuration, network devices may not be attached to USB, and so
enumerating USB may not be necessary. Enhance the scripts to make this
step optional, so that the user can decrease boot time if they don't
need USB.
This change is performed by moving the "usb start" invocation into a
standalone variable. If the user desires, they can replace that
variable's value with some no-op command such as "true" instead.
Booting from a USB storage device always needs to enumerate USB devices,
so this action is still hard-coded.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the DTS documentation for the Micrel KSZ90x1 binding.
The original document was from:
[commit 4b405efbe12de28b26289282b431323d73992381 from the Linux kernel]
This takes the original document and adds a clarification on how the skew
values are represented in the code.
References:
Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf
Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new member 'tbiaddr' to tsec_private struct. For non-DM driver,
it is initialized as CONFIG_SYS_TBIPA_VALUE, but for DM driver, we
can get this from device tree. Update the bindings doc as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adapted from the same file name in the kernel device tree bindings
documentation, to use with U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}
A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.
For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver for VSC9953 L2 switch IP supports many features and
the documentation needs to be updated.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a parameter to the function setup_early_uart() to either
enable or disable the internal BayTrail legacy UART. Since the name
setup_early_uart() does not match its functionality any more, lets
rename it to setup_internal_uart() as well in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the documentation for the memory-down parameters
of the Intel FSP. To configure a board without SPD DDR DIMM but
with onboard DDR chips. The values are taken from the coreboot
header:
src/soc/intel/fsp_baytrail/chip.h
(git ID da1a70ea from 2016-01-16 as reference).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Andrew Bradford <andrew.bradford@kodakalaris.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Replace ns16550.txt with binding files from Linux kernel. As suggested
by Stephen Warren, we should keep the directory structure, filenames,
and file content identical to the bindings in the Linux kernel.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
GPIO, I2C, LCD and HDMI are now implemented. We have more than one PMIC.
There is an implementation to run the CPU at full speed although it does
not seem to make much difference.
Update the README to cover recent developments.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
This script has proved useful for parsing datasheets and creating register
shift/mask values for use in header files. Include it in case it is useful
for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds driver model support to lpuart serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Adding timer init function in timer-uclass driver to create and
initialize the timer device on platforms where u-boot,dm-pre-reloc
is not used. Since there will be multiple timer devices in the
system, adding a tick-timer node in chosen node to know which
timer device to be used as tick timer in u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
This patch adds code which sets up 2-level page tables on ARM64 thus
extending available VA space. CPUs implementing 64k translation
granule are able to use direct PA-VA mapping of the whole 48 bit
address space.
It also adds the ability to reset the SCTRL register at the very beginning
of execution to avoid interference from stale mappings set up by early
firmware/loaders/etc.
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Document the usage of 'qfw' command
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c
writes/reads the tail of each NOR flash bank to check if the device
really resides there.
If CS1_SPLIT were enabled, the support card would always require two
NOR flash devices to be inserted for the correct NOR detection.
This is not probably what we want.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Various updates did not make it through to this board. Also the instructions
for building a SPI image are no-longer correct. Fix these so that Jerry can
boot to a prompt again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.
This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
These boards are similar enough to be supported in a single defconfig
file. Distinguish one from another by "DEVICE_TREE" from the command
line. The how-to-build in doc/README.uniphier should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These two are similar enough to be merged into a single
defconfig file. Distinguish one from another by "DEVICE_TREE"
from the command line. The how-to-build in doc/README.uniphier
should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since both altera_jtag_uart and altera_uart are converted to driver
model, remove them from the list of drivers remaining to convert.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Chin Liang See <clsee@altera.com>
We now using imagename to select rockchip's spl hdr & spl size.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
show how to packet rk3036 uboot image and boot from SD
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Series-to: u-boot
Series-version: 8
Series-cc: Lin Huang <hl@rock-chips.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
The optional parameter bootable is added in gpt command to set the
partition attribute flag "Legacy BIOS bootable"
This flag is used in extlinux and so in with distro to select
the boot partition where is located the configuration file
(please check out doc/README.distro for details).
With this parameter, U-Boot can be used to create the boot partition
needed for device using distro.
example of use:
setenv partitions "name=u-boot,size=60MiB;name=boot,size=60Mib,bootable;\
name=rootfs,size=0"
> gpt write mmc 0 $partitions
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x0001e021 "u-boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: cceb0b18-39cb-d547-9db7-03b405fa77d4
2 0x0001e022 0x0003c021 "boot"
attrs: 0x0000000000000004
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: d4981a2b-0478-544e-9607-7fd3c651068d
3 0x0003c022 0x003a9fde "rootfs"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 6d6c9a36-e919-264d-a9ee-bd00379686c7
> part list mmc 0 -bootable devplist
> printenv devplist
devplist=2
Then the distro scripts will search extlinux in partition 2
and not in the first partition.
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
./doc/README.gpt entry has been updated to explain usage of "gpt verify"
command.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a README with a brief guide to porting serial drivers over to use
driver model.
Add a timeline also. All serial drivers should be converted by the end
of January 2016.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for loading splash image from an SD card formatted with
a filesystem. Update boards to maintain original behavior where needed.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
short strings can be used in type parameter of gpt command
to replace the guid string for the types known by u-boot
partitions = name=boot,size=0x6bc00,type=data; \
name=root,size=0x7538ba00,type=linux;
gpt write mmc 0 $partitions
and they are also used to display the type of partition
in "part list" command
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x0000037f "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: d117f98e-6f2c-d04b-a5b2-331a19f91cb2
2 0x00000380 0x003a9fdc "root"
attrs: 0x0000000000000000
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 25718777-d0ad-7443-9e60-02cb591c9737
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
