It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The width is set up in single_of_to_plat() and can only have three values,
all of which result in a non-zero divisor. Add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 331154)
With gcc-11 we get a multiple errors here as the declarations for
mscc_pinctrl_ops and mscc_gpio_ops are missing an extern.
CC: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import R8A779A0 V3U PFC tables from Linux 5.12, commit 9f4ad9e425a1
("Linux 5.12") . Add parts of PFC table integration from
pinctrl: renesas: Add R8A779A0 V3U PFC tables
by Hai Pham <hai.pham.ud@renesas.com>" .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") . This is a rather large
commit, since the macros in sh-pfc.h also got updated, so
all the PFC tables must be updated in lockstep.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
If reg property of pinctrl-single node requires address translation then
probe fails with following message:
single-pinctrl pinctrl@4301c000: failed to get base register size
This is because driver uses dev_read_addr_size() to get size which also
tries to fetch untranslated addr and fails.
Fix this by using dev_read_addr_size_index() which takes care of address
translation and also makes following dev_read_addr() call redundant.
This fixes Ethernet failures on TI's AM654 based EVMs due to lack of
pinmux configuration.
Fixes: 9fd8a430f3 ("pinctrl: single: get register area size by device API")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The V3U SoC has several unlock registers, one per register group. They
reside at offset zero in each 0x200 bytes-sized block.
To avoid adding yet another table to the PFC implementation, this
patch adds the option to specify an address mask instead of the fixed
address in sh_pfc_soc_info::unlock_reg.
This is a direct port of Linux 5.12 commit e127ef2ed0a6
("pinctrl: renesas: Implement unlock register masks") by
Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The help text for Gen2 entries had a copy paste error, still containing
the Gen3 string, while the description was correctly listing Gen2. Fix
the help text.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The help text in the Kconfig file was always a copy of the same thing.
Move single copy into the common PFC driver entry instead. Also fix a
copy-paste error in the PFC help text, which identified PFC as clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
As reported by Coverity Scan for Das U-Boot, the 'less-than-zero'
comparison of an unsigned value is never true.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The test adds two pinmux nodes to the device tree, one to test when a
register changes only one pin's mux (pinctrl-single,pins), and the other
to test when more than one pin's mux is changed (pinctrl-single,bits).
This required replacing the controller's register access functions when
the driver is used on sandbox.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
It allows to display the muxing of a given pin. Inspired by more recent
versions of the Linux driver, in addition to the address and the value
of the configuration register I added the pin function retrieved from
the DT. In doing so, the information displayed does not depend on the
platform, being a generic type driver, and it can be useful for debug
purposes.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configuration of pinmux registers was implemented with duplicate
code which can be removed by adding two functions for read/write access.
Access to 8-bit registers has also been added.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is inspired by more recent versions of the Linux driver.
Replacing the default value 0xffffffff of the function mask with 0 is
certainly more conservative in case the "pinctrl-single,function-mask"
DT property is missing.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
In more recent versions of the Linux kernel the driver's probe function
returns an error if the "pinctrl-single,register-width" DT property is
missing. The lack of this information, in fact, does not allow to know
whether to access the registers of the controller at 8, 16, ... bits.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use dev_read_addr_size to get size of the controller's register area.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The dev_dbg(dev, " reg/val 0x%pa/0x%08x\n", ®, val); prints the 'reg'
address preceded by the prefix 0x0x instead of 0x. This because the
printf '%pa' format specifier already prepends the prefix '0x' to the
address displayed.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The pinmux configuration DT node of a peripheral does not define a
physical address but an offset. Only by adding it to the base address of
the controller it is possible to calculate the physical address of the
register to be configured. Printing an offset also requires a different
formatting option than a physical address.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The 'n' variable is used as a loop counter, not as a physical address,
and is used in a comparison with an int. So it makes sense to change
its type from phys_addr_t to int.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Update the code to use -ENOSYS, which is the correct error code for an
unimplemented system call in U-Boot.
Also we should not check for a missing operations array as this is not
permitted. For now this can be covered by an assert().
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmBi3oscHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKr+CACDQJT4hGCDwc7XFjOw
RN0aGRC6eGF4q3kL4VjBazCM1SBNs3vdVZV+bnYl3ioSNzy43K7CyFqqUlJH7CJV
dakvNn71xVoQD3Xw3+I4ALibbD/tlli4vwMOeN4KlWCIdNrRrtUOQpli0M0BVDkL
0IWMDf6OLAfw1uytubsQBVitFBQoiuE3ihSphoyTOFwQdI+xsMue5uVq+O0kDqU4
gotBzmoSq5LONyNSdpHxXqujU4oXkuOr/TsVTOoRtEkQ63zVbfNWOg951is+UaHa
F7f6W+cWdlb+HBs6TFb+Gva0TMmyWIH05jyIS52k6uFVM0tyFCOJFeZp81cjPP4L
O3KI
=ywRG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
The EPHY LEDs of mt7629 can be used as JTAG. This patch adds the jtag pin
group to the pinctrl driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mtk pinctrl driver is a combination driver with support for both
pinctrl and gpio. When this driver is used in SPL, gpio support may not be
enabled, and this will result in a compilation error.
To fix this, macros are added to make sure gpio related code will only be
compiled when gpio support is enabled.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This is a bug fix for mtk pinctrl common part. Appearently pins should be
used instead of grps in mtk_get_pin_name().
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Renesas RZ/G2E (a.k.a. r8a774c0) is pin compatible with R-Car
E3 (a.k.a. r8a77990), however it doesn't have several automotive
specific peripherals.
This patch hooks R8A774C0 SoC with the pfc driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Sync the R8A77990 SoC PFC tables with Linux 5.11 , commit f40ddce88593.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
It is convenient to be able to adjust some of the flags for a GPIO while
leaving others alone. Add a function for this.
Update dm_gpio_set_dir_flags() to make use of this.
Also update dm_gpio_set_value() to use this also, since this allows the
open-drain / open-source features to be implemented directly in the
driver, rather than using the uclass workaround.
Update the sandbox tests accordingly. This involves a lot of changes to
dm_test_gpio_opendrain_opensource() since we no-longer have the direciion
being reported differently depending on the open drain/open source flags.
Also update the STM32 drivers to let the uclass handle the active low/high
logic.
Drop the GPIOD_FLAGS_OUTPUT() macro which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is more useful to be able to read all the flags, not just the direction
ones. In fact this is what the STM32 driver does. Update the method name
to reflect this.
Tweak the docs a little and use 'flagsp' as the return argument, as is
common in driver model, to indicate it returns a value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The current method is a misnomer since it is also used (e.g. by stm32) to
update pull settings and open source/open drain.
Rename it and expand the documentation to cover a few more details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
SAMA7G5 supports slew rate configuration. Adapt the driver for this.
For switching frequencies lower than 50MHz the slew rate needs to
be enabled. Since most of the pins on SAMA7G5 fall into this category
enabled the slew rate by default.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Bind only the enabled GPIO subnode, to avoid to probe the node
"gpio-controller" present in SOC dtsi (disabled by default) but
not enabled in the included pincontrol dtsi file.
For example, in stm32mp15xxac-pinctrl.dtsi 2 gpio bank are absent:
gpioj: gpio@5000b000
gpiok: gpio@5000c000
Then these GPIO are absent in output of command "dm tree" and
"gpio status -a"
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
OTYPE can be used for output or for alternate function to select
PP = push-pull or OP = open-drain mode, according reference manual
(Table 81. Port bit configuration table).
This patch removes this indication for input pins and adds it
for AF and output pins for pinmux command output.
Fixes: b305dbc08b ("pinctrl: stm32: display bias information for all pins")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Instead of redefining a pin's name size, use PINNAME_SIZE defined
in include/dm/pinctrl.h
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pin-controller pin's name must be equal to pin's name used in device
tree with "pins" DT property.
Issue detected on stm32mp157c-ev1 board with goodix touchscreen.
In DT, the goodix's pin is declared in DT with the node:
goodix_pins: goodix {
pins = "gpio14";
bias-pull-down;
};
Whereas in stmfx pin-controller driver, pin's name are equal to
"stmfx_gpioxx" where xx is the pin number.
This lead to not configure stmfx's pins at probe because pins is
identified by its name (see pinctrl_pin_name_to_selector() in
pinctrl-generic.c) and stmfx pin "gpio14" can't be found.
To fix this issue, come back to the original stmfx pin's name.
Revert "pinctrl: stmfx: update pin name"
This reverts commit 38d30cdcd65c73eeefac5efa328ad444a53b77dd.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds pinctrl support for MediaTek MT7620 SoC.
The MT7620 SoC supports only pinmux.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
