Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
The FIT config node has reversed ATF and u-boot: ATF is set to 'firmware' but
u-boot is set to 'loadables'.
This script can work previously because spl fit driver wrongly appends fdt to
all loadable images. With the issue fixed in commit 9d15d1d1c2 ("Revert
"common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"") the
u-boot in 'loadables' does not have fdt appended and fails to work. So correct
the script by moving u-boot to 'firmware' and ATF to 'loadables'.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reported-by: Matt Porter <mporter@konsulko.com>
Tested-by: Matt Porter <mporter@konsulko.com>
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Similar change was done in past by commit 3b644a3c2f
("arm64: zynqmp: Provide a config to not map DDR region in MMU table").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If ATF doesn't exist generate u-boot.itb without it and let U-Boot run in
EL3. Still keep warning to let user know that ATF/BL31 is missing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I found this issue when was running py/test.py on zcu102 which is for me by
default setup to SD boot mode without any way to change boot mode.
Alternative software bootmode selection to JTAG is not working because JTAG
mode is 0 which also reset value for it. That's why saying SPL to take
u-boot.itb from RAM instead of SD in SD boot mode is not possible via
alternative bootmode selection.
That's why setup third boot mode to JTAG(BOOT_DEVICE_RAM) as final
fallback.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This information is shown already that's why there is no reason to print it
again via custom prints.
U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 09:59:05 +0100)
mmc boot
Trying to boot from MMC1
or
U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 10:49:46 +0100)
qspi boot
Trying to boot from SPI
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to include full DT when only some nodes are enough to
use. It will save some space.
Retested with FSBL for initial SoC setup. SPL didn't work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Users have option to overwrite default device tree
(CONFIG_DEFAULT_DEVICE_TREE) via environment variable DEVICE_TREE.
Feature has been added long time ago by commit 74de8c9a16
("dts/Makefile: Build the user specified dts") for a little bit different
reason.
But this variable can be also used for different purpose like choosing
proper configuration from FIT image in SPL.
And this is the functionality I would like to use on Xilinx Zynq devices
that current u-boot.img can be composed in the same way based on OF_LIST
and different configuration is taken based on platform specific SPL.
SPL requires low level ps7_init_gpl configuration that's why different
boards require different SPL with fixed board_fit_config_name_match().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of symlink include origin file and just change model description.
Difference is not in DT but in ps7_init configurations which is taken based
on device tree name that's why the same DT can't be used.
Also update model and update comments to match configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pinctrl is handled via firmare interface that's why move it there without
reg property and new compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtbs_check is showing warning around GIC compatible property as
interrupt-controller@f9010000: compatible: ['arm,gic-400', 'arm,cortex-a15-gic']
is not valid under any of the given schemas
Similar change has been done also by Linux kernel commit 5400cdc1410b
("ARM: dts: sunxi: Fix GIC compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Node name should be <name>@<address> which is not how partitions are
described.
Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In kernel 5.4, support has been added for reading MTD devices via
the nvmem API.
For this the mtd devices are registered as read-only NVMEM providers
under sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are identical
then the second mtd device fails to get registered as a NVMEM provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock-cells and clock-output-names for sdhci0 and sdhci1.
These are needed for linux sdhci driver from 5.4 version onwards.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reset controller is handled via firmware that's why it should be the part
of firmware node. Origin solution hasn't been removed when above change was
applied by commit b07e97b4ba ("arm64: zynqmp: Use reset header in
zynqmp.dtsi").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Sync zynqmp fpga manager with mainline.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
None name address should be aligned with address. DTC 1.5.1 is reporting
issues related to that.
arch/arm/boot/dts/zynq-zc770-xm010.dts:106.10-119.4: Warning
(spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format
error, expected "1"
arch/arm/boot/dts/zynq-zc770-xm013.dts:101.19-109.4: Warning
(spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format
error, expected "2"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The same change has been done for Zynq by commit 1241c72b6db1
("ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property")
in mainline Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the Linux kernel commit 700a38b27eef
("Input: gpio_keys - switch to using generic device properties")
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dtc has new checks for I2C and SPI buses.
Fix the warnings in node names and unit-addresses.
Warning from Linux kernel:
arch/arm/boot/dts/zynq-zc702.dts:187.13-190.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dts:191.13-194.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dts:195.13-198.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech-pc device tree from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The card-detect GPIO and any other GPIO access currently doesn't work in
U-Boot SPL on any STM32 platform and crashes the SPL. To work around this
problem on AV96 right before release, remove the cd-gpios from DT. This
patch must be reverted right after release, once the proper fix for the
GPIO driver, "gpio: stm32: support gpio ops in SPL", is applied.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When generating the MAC address based on the boards serial number
the last digit was overwritten with the null termination. That way
boards with serial numbers close to each other would use the same
MAC address.
Signed-off-by: Jan-Christoph Tebbe <Jan-Christoph.Tebbe@ithinx.io>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix VI_I2C clock source type. Will be needed by VI_I2C driver.
Also added use of INTERNAL_ID macro in two places, needed to keep
the id returned to 8 bits.
Signed-off-by: Tom Warren <twarren@nvidia.com>
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:
p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This commit removes the programming sequence that enables PLLE and UPHY
PLL hardware power sequencers. Per TRM, boot software should enable PLLE
and UPHY PLLs in software controlled power-on state and should power
down PLL before jumping into kernel or the next stage boot software.
Adds call to board_cleanup_before_linux to facilitate this.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This adds to the DT the I2C controllers that connect to the board ID EEPROM,
etc. With this change, you can now probe all I2C devices on a TX1 board.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Enable pre console buffer for rk3399 platform.
This would help to capture the console messages prior to
the console being initialised. Enabling this would help
to capture all the console messages on video output source
like HDMI. So we can find the full console messages of
U-Boot proper on HDMI display when enabled it for RK3399
platform boards.
Buffer address used for pre console is 0x0f200000 which is
ram base plus 240MiB. right now the Allwinner SoC is using
similar computation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
