Commit graph

16 commits

Author SHA1 Message Date
Kuo-Jung Su
e82a316d7f usb: ehci: add Faraday USB 2.0 EHCI support
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:

1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
   also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
   compatible with the general TDI implementation
   found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
   several ways. But since U-boot doesn't support ISOC,
   we don't have to worry about that.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2013-06-12 22:22:51 +02:00
Kuo-Jung Su
aa1550588c usb: hub: make minimum power-on delay configurable
This patch makes the minimum power-on delay for USB HUB
become configurable. The original design waits at least
100 msec here, but some EHCI controlers(e.g. Faraday EHCI)
are known to require much longer delay interval.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2013-06-12 22:22:51 +02:00
Vivek Gautam
55f4b57542 usb: fix: Fixing Port status and feature number constants
Fix the Port status bit constants and Port feature number
constants as a part of USB 2.0 and USB 3.0 Hub class.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-06 02:16:36 +02:00
Vivek Gautam
0bf796f7ae usb: hub: Parallelize power-cycling of root-hub ports
Untill now we power-cycle (aka: disable power on a port
and re-enabling again) one port at a time.
Delay of 20ms for Port-power to change multiplies with
number of ports in this case.
So better we parallelize this process:
disable power on all ports, wait for port-power to stabilize
and then re-enable the power subsequently.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-06 02:16:36 +02:00
Vivek Gautam
6497c66704 USB: SS: Add support for Super Speed USB interface
This adds usb framework support for super-speed usb, which will
further facilitate to add stack support for xHCI.

Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
289f3cb28a usb: hub: Fix enumration timeout
Patch b6d7852c increases timeout for enumeration, taking
worst case to be 10 sec.
get_timer() api returns timestamp in milliseconds, which is
what we are checking in the do-while() loop in usb_hub_configure()
(get_timer(start) < CONFIG_SYS_HZ * 10).
This should give us a required check for 10 seconds, and thereby
we don't need to add additional mdelay of 100 microseconds in
each cycle.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
020bbcb76b usb: hub: Power-cycle on root-hub ports
XHCI ports are powered on after a H/W reset, however
EHCI ports are not. So disabling and re-enabling power
on all ports invariably.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:22 +02:00
Vivek Gautam
ceb4972a8f usb: common: Weed out USB_**_PRINTFs from usb framework
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05 23:54:21 +02:00
Milind Choudhary
359439d288 usb: Clean up newly allocated device nodes in case of configuration failure
If probe of a newly connected device fails for some reason, clean up
the allocated entry in usb_dev array.

Signed-off-by: Milind Choudhary <milindc@codeaurora.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-17 15:38:15 +01:00
Vipin Kumar
b6d7852cf8 usbh/ehci: Increase timeout for enumeration
The current logic reads the port status just once after usb_hub_power_on and
expects the portstatus and portchange to report the connection status
immediately and correctly.

Few pen drives are not able to report both of them immediately ie. those pens
report the connection change but not the connected state after the first read.
This opportunity once lost is gone for ever because the u-boot, unlike linux or
any other OS, works in polling mode.

This patch modifies the logic to read the port status continuously until the
portstatus and portchange both report a connection change as well as a connected
state or no connection change and no connection. This logic is placed in a
timeout of 10 sec. At the end of it, the pen drive would have either reported a
ONE or a ZERO in bit 1 of portstatus as well as portchange.

It enhances the set of pen drives which can eventually be detected by u-boot

Note: This 10 second timeout is based purely on several experiments done with
the broken pen drives

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-12-17 15:38:15 +01:00
Lucas Stach
c7e3b2b586 usb: lowlevel interface change to support multiple controllers
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.

Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-10-15 11:54:00 -07:00
Lucas Stach
93ad908c43 usb: do explicit unaligned accesses
usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.

Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.

v2: fix typo found by Thomas Langer

v3: rebased on top of u-boot-usb/master

Signed-off-by: Lucas Stach <dev@lynxeye.de>
2012-09-21 00:05:00 +02:00
Puneet Saxena
f57661394a USB: Align buffers at cacheline
This avoids cache-alignment warnings shown in console
when a usb command is entered.

Whenever X bytes of unaligned buffer is invalidated, arm core
invalidates X + Y bytes as per the cache line size and throws
these warnings.

Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Marek Vasut <marex@denx.de>
2012-05-20 08:32:32 +02:00
Mike Frysinger
5b84dd67cf usb: replace wait_ms() with mdelay()
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func.  This also fixes the build errors:

ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
2012-03-19 00:08:16 +01:00
Wolfgang Grandegger
a1a28c6e64 USB: relax usbcore reset timings
Following the corresponding Linux code, this patch relaxes reset timings
waiting at least 100ms after power to the ports. There are some reports
that it helps make enumeration work better on some high speed devices.
Furthermore, the wait is only done once after power has been enabled
on all ports.

CC: Remy Bohmer <linux@bohmer.net>
CC: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-03-03 16:56:35 +01:00
Marek Vasut
23faf2bc9e USB: Separate out USB hub driver
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-03-03 16:55:24 +01:00