These options should not be exposed to other platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
To support more input characters (longer stings pasted into the U-Boot
prompt) without dropping, lets selects the recently added UART RX
buffer for these boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To support more input characters (longer stings pasted into the U-Boot
prompt) without dropping, lets selects the recently added UART RX
buffer for these boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pasting longer lines into the U-Boot console prompt sometimes leads to
characters missing. One problem here is the small 16-byte FIFO of the
legacy NS16550 UART, e.g. on x86 platforms.
This patch now introduces a Kconfig option to enable RX buffer support
for all DM based serial drivers. With this option enabled, I was
able paste really long lines into the U-Boot console, without any
characters missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 6822cf3ec7.
As Bin Meng has tested and pointed out, we don't need the RX interrupt
for the RX buffer support at all. Just reading all available characters
into a buffer is sufficient to solve the problem with the dropped
characters upon long lines pasted into the U-Boot prompt. Since this
RX buffer support can be implemented in a generic way, without any
device specifica (e.g. for the ns16550), I'll post a new patch with
a new serial RX buffer support for DM, which all DM based serial
drivers can use.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Let's imply the 'pci' command to access the de facto interconnect
bus in an x86 system.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the SPI flash device.
This introduces a Kconfig option CONFIG_FSP_LOCKDOWN_SPI for such
FSPs. When it is on, U-Boot will configure the SPI opcode registers
before the lock-down.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the ICH SPI opcode registers configuration is done in the
ich_spi_remove() routine, a little bit weird but that's how current.
Linux MTD driver works. This changes to move the opcode registers
configuration to a separate routine ich_spi_config_opcode() which
might be called by U-Boot itself as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the ICH SPI controller driver reads the controller lock
status from its register in the probe routine and saves the lock
status to a member of priv. Later the driver uses the cached status
from priv to judge whether the controller setting is locked and do
different setup.
But such logic is only valid when there is only the SPI controller
driver that touches the SPI hardware. In fact the lock status change
can be trigged outside the driver, eg: during the fsp_notify() call
when Intel FSP is used.
This changes the driver to read the lock status every time when an
SPI transfer is initiated instead of reading the cached one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
To i.MX7ULP, we need to create two info instances for
iomux0 and iomux1 respectively, otherwise iomuxc0/1 will
share one info instance and use one base, because imx_pinctrl_probe
will use info to store base address and etc. But iomuxc0/1
actually have different base address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
when using SHARE_MUX_CONF_REG, wrong mask is used for
writing config value, which causes mux value is cleared.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Some files for i.MX do not yet have the SPDX ID to reference the correct
license.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Enable Serial Download Protocol (SDP) in SPL and U-Boot. This is
useful to make use of imx_usb to download the complete U-Boot
(u-boot.img) after SPL has been downloaded. The U-Boot command
sdp allows to enumerate as SDP capable device again, e.g. to
download a Linux kernel and/or U-Boot script.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Use a completely independent USB Product ID for SPL. This allows
to differentiate a SDP running in SPL and SDP running in a U-Boot
which could not read the config block successfully.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Document the U-Boot Serial Download Protocol implementation and
some typical use cases.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Add USB serial download protocol support to SPL. If the SoC started
in recovery mode the SPL will immediately switch to SDP and wait for
further downloads/commands from the host side.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Add a new command to start USB Serial Download Protocol (SDP)
state machine.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Support U-Boot images in SPL so that u-boot.img files can be
directly downloaded and executed. Furthermore support U-Boot
scripts download and execution in full U-Boot so that custom
recovery actions can be downloaded from the host in a third
step.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add SDP (Serial Downloader Protocol) implementation for U-Boot. The
protocol is used in NXP SoC's boot ROM and allows to download program
images. Beside that, it can also be used to read/write registers and
download complete Device Configuration Data (DCD) sets. This basic
implementation supports downloading images with the imx header format
reading and writing registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Move the imximage.h header file to a common location so we can make
use of it from U-Boot too.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.
E.G. something like:
---------- ---------- Bus segment 1 - - - - -
| | SCL/SDA | |-------------- | |
| |------------| |
| | | | Bus segment 2 | |
| Linux | GPIO 1..N | MUX |--------------- Devices
| |------------| | | |
| | | | Bus segment M
| | | |---------------| |
---------- ---------- - - - - -
SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Note commit log from kernel
commit 92ed1a76("i2c: Add generic I2C multiplexer using GPIO API")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com> (i.MX6QP-Sabreauto)
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Add i2c driver which can be used on both STM32F7 and STM32H7.
This I2C block supports the following features:
_ Slave and master modes
_ Multimaster capability
_ Standard-mode (up to 100 kHz)
_ Fast-mode (up to 400 kHz)
_ Fast-mode Plus (up to 1 MHz)
_ 7-bit and 10-bit addressing mode
_ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask)
_ All 7-bit addresses acknowledge mode
_ General call
_ Programmable setup and hold times
_ Easy to use event management
_ Optional clock stretching
_ Software reset
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Otherwise:
drivers/usb/gadget/f_fastboot.c:564:32: warning: format "%lx" expects
argument of type "long unsigned int", but argument 3 has type "unsigned
int" [-Wformat=]
Signed-off-by: Tom Rini <trini@konsulko.com>
Staticize a few functions and variables which are no longer exposed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The db-88f6820-amc has four chips with 2Gb density giving a total of 1GB
DRAM. Update the board_topology_map to reflect the correct
configuration.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Cc: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building the flash zImage code on aarch64 we see warnings about
pointer size casts. Use uintptr_t instead to correct these.
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-By: Sam Protsenko <semen.protsenko@linaro.org>
There is no guarantee that commands are null-terminated in the USB
request buffer, so limit the length of data that is printed.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Steve Rae <steve.rae@raedomain.com>
Fastboot loads an image at CONFIG_FASTBOOT_BUF_ADDR, but currently
tells do_bootm() to look for an image at $loadaddr. This breaks if
CONFIG_FASTBOOT_BUF_ADDR is different from the current user-set
loadaddr.
Instead, tell do_bootm() to pick up the image where it was laoded.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
With the change to the environment code to remove the common init stage
of pointing to the default environment and setting it as valid, combined
with the change to switch gd->env_valid from 0/1/2 to an enum we now
must set env_valid to one of the enum values rather than an int. And in
this case, not only was setting it to an int wrong, it was now the wrong
value. Finally, in the case of ENV_IS_NOWHERE we must still say that
our envionrment is invalid after init for things to continue to
function.
Fixes: 7938822a6b ("env: Drop common init() functions")
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v3:
- Actually include changes for env/nowhere.c
Since commit 576e3cc700 ("usb: host: xhci-dwc3: Add dual role mode
support from DT"), warning is displayed if dr_mode is not specified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Merge sys_reset data of LD4, Pro4, sLD8 and Pro5
- Merge sys_reset data of LD11 and LD20
- Use primitive UNIPHIER_RESETX() macro because bit assignments for
system reset will be changed for every SoC in the future
- Add NAND and eMMC resets
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 82d075e79f.
Commit 82d075e79f ("ARM: uniphier: fix ROM boot mode for PH1-sLD3")
was a workaround for sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to simplify the init code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit bcc51c1512.
Commit bcc51c1512 ("ARM: uniphier: move lowlevel debug init code
after page table switch") was intended to support lowlevel debug for
sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to enable lowlevel debug earlier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:
$ make uniphier_v8_defconfig
warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)
While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
