Commit graph

9 commits

Author SHA1 Message Date
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
a4d403290e usb: dwc2: make casts of ep->dma_buf consistent
In most places in the code we cast this to an unsigned long, but in one
place we cast to an unsigned int.  For consistency and to fix a warning
on 64bit targets, always cast this to unsigned long.  For the long term
we should however change the declaration of dma_buf.

Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-05 12:09:43 -05:00
Seung-Woo Kim
a939af0c74 usb: dwc2: Align size of invalidating dcache before starting DMA
During using dwc2 usb gadget, if usb message size is too small,
following cache misaligned warning is shown:

   CACHE: Misaligned operation at range [bfdbcb00, bfdbcb04]

Align size of invalidating dcache before starting DMA to remove the
warning.

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
2017-09-27 12:12:23 +02:00
Xu Ziyuan
9424f14183 usb: dwc2 : invalidate dcache before starting DMA
Invalidate dcache before starting the DMA to ensure coherency. In case
there are any dirty lines from the DMA buffer in the cache, subsequent
cache-line replacements may corrupt the buffer in memory while the DMA
is still going on. Cache-line replacement can happen if the CPU tries to
bring some other memory locations into the cache while the DMA is going
on.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:19 -06:00
Roger Quadros
4d5b637843 usb: s3c-otg: Fix remaining bytes in debug messages
Remaining bytes means bytes that are not yet transferred
and not the bytes that were transferred in the last transfer.

Reported-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
2016-04-25 17:56:30 +02:00
Roger Quadros
842769ea51 usb: s3c-otg: Fix short packet for request size > ep.maxpacket
Request size can be greater than ep.packet and still end in a
short packet. We need to tackle this case as end of transfer
(if short_not_ok is not set) as indicated in USB 2.0 Specification [1],
else we get stuck up on certain protocols like fastboot.

[1] - USB2.0 Specification, Section 5.3.2 Pipes

Reported-by: Steve Rae <steve.rae@broadcom.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <steve.rae@broadcom.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2016-04-25 17:56:30 +02:00
Marek Vasut
e179cedd09 usb: s3c-otg: Tweak the comments
The driver is actually for the Designware DWC2 controller.
Tweak the comments in the driver to reflect this fact.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-12-17 21:54:40 +01:00
Marek Vasut
507e677bc4 usb: s3c-otg: Rename remaining macros
The driver is actually for the Designware DWC2 controller.
This patch renames the remaining S3C_* macros to match the
DWC2 naming.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-12-17 21:54:40 +01:00
Marek Vasut
be5e4bdced usb: s3c-otg: Rename sources to dwc2_*c
The driver is actually for the Designware DWC2 controller.
This patch renames the local source files to dwc2_*c and
adjusts the Makefile to use the new names.

Signed-off-by: Marek Vasut <marex@denx.de>
2015-12-17 21:54:40 +01:00
Renamed from drivers/usb/gadget/s3c_udc_otg_xfer_dma.c (Browse further)