Commit graph

34341 commits

Author SHA1 Message Date
Felipe Balbi
76bfd1625a arm: am43xx: switch over to CONFIG_ENV_IS_IN_FAT
By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
without having to modify the configuration header.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-10-23 11:53:01 -04:00
Felipe Balbi
41f1d40d92 common: Makefile: allow for spl builds with env_fat
If CONFIG_SPL_BUILD and CONFIG_ENV_IS_IN_FAT are
defined, u-boot spl will fail to build. Fix that.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-10-23 11:53:01 -04:00
Stefan Herbrechtsmeier
f5c30c1b1c omap3: overo: Add usb host support
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23 11:53:01 -04:00
Stefan Herbrechtsmeier
4ed914a243 omap3: overo: Separate module and expansion board MUX configuration
Separate overo module and expansion board MUX configuration. This allows
an foreign expansion board to use the boot loader without any adaption.
It only needs to save the expansion name in the EEPROM to load a
specific device tree.

Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23 11:53:01 -04:00
Stefan Herbrechtsmeier
113429a27b omap3: overo: Move ethernet setup to board_eth_init function
Move ethernet setup to the board_eth_init function and select
the available network devices via expansion id.

Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23 11:53:01 -04:00
Stefan Herbrechtsmeier
f2565a551c omap3: overo: Call bootm only after successful nand read
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23 11:53:01 -04:00
Hao Zhang
26459488b7 ARM: keystone: cmd_ddr3: add ddr3 commands to test ddr
Add ddr3 commands:

test <start_addr in hex> <end_addr in hex> - test DDR from start\n
	address to end address\n
ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n
	compare DDR data of (size) bytes from start address to end
	address\n
ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n
	in DDR data at <addr>, the command will read a 32-bit data\n
	from <addr>, and write (data ^ bit_err) back to <addr>\n

Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used
for ddr3 commands and for now it's not needed any more.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Vitaly Andrianov
89f44bb0ce keystone2: ecc: add ddr3 error detection and correction support
This patch adds the DDR3 ECC support to enable ECC in the DDR3
EMIF controller for Keystone II devices.

By default, ECC will only be enabled if RMW is supported in the
DDR EMIF controller. The entire DDR memory will be scrubbed to
zero using an EDMA channel after ECC is enabled and before
u-boot is re-located to DDR memory.

An ecc_test environment variable is added for ECC testing.
If ecc_test is set to 0, a detection of 2-bit error will reset
the device, if ecc_test is set to 1, 2-bit error detection
will not reset the device, user can still boot the kernel to
check the ECC error handling in kernel.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Vitaly Andrianov
079da2d514 ARM: keystone: msmc: extend functionality of SES
Add functions to set/get SES PMAX values of Pivilege ID pair.
Also add msmc module definitions.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
e165b1d34c dma: ti-edma3: introduce edma3 driver
The EDMA3 controller’s primary purpose is to service data transfers
that you program between two memory-mapped slave endpoints on the device.

Typical usage includes, but is not limited to the following:
- Servicing software-driven paging transfers (e.g., transfers from external
  memory, such as SDRAM to internal device memory, such as DSP L2 SRAM)
- Servicing event-driven peripherals, such as a serial port
- Performing sorting or sub-frame extraction of various data structures
- Offloading data transfers from the main device DSP(s)
- See the device-specific data manual for specific peripherals that are
  accessible via the EDMA3 controller

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Hao Zhang
00b821f16e board: k2e_evm: add network support
This patch adds network support code and enables keystone_net
driver usage for k2e_evm evaluation board.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
69a3b81141 ARM: keystone: clock: add support for K2E SoCs
For K2E and K2L SoCs clock output from PASS PLL has to be enabled
after NETCP domain and PA module are enabled. So create new function
for that and call it after PA module is enabled.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
c05d05e720 net: keystone_net: increase PHY auto negotiate time
The new Marvel PHY (88E1514) used on K2L/K2E EVM requires longer time
to auto negotiate with SoC's SGMII port.

It can take about 3 sec to up the PHY after reset, so add code to
expose sgmii auto negotiation waiting process.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
ff11c7697c net: keystone_net: add Keystone2 K2E SoC support
The Keystone2 Edison SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2E SoCs.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
3c61502aad net: keystone_serdes: add keystone K2E SoC support
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
2162faaf58 ARM: keystone2: keysonte_nav: add support for K2E SoC
Keystone2 Edison SoC uses the same keystone navigator, but
uses different NETCP PktDMA definitions. This patch adds
required definitions.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:29 -04:00
Khoronzhuk, Ivan
a4d2adee11 net: keystone_net: use general get link function
The phy framework has function to get link, so use it
instead of own implementation.

There is no reason to check SGMII link while sending each
packet, phy link is enough. Check SGMII link only while
ethernet open.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
3fe93623cc net: keystone_net: register eth PHYs on MDIO bus
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.

Startup PHY at the ethernet open.

Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.

For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
550c5ce6f5 net: keystone_net: register MDIO bus
Currently MDIO framework is not used to configure Ethernet PHY.
As result some of already implemented functions are duplicated.
So register MDIO bus in order to use it. On that stage it's just
registered, it'll be used as we start to use PHY framework.

Use mdio bus read/write/reset functions in the driver.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
1920e905ef net: keystone_net: use mdio_reset function
Don't use mdio_enable twice while eth open. Also rename it to
keystone2_mdio_reset as more appropriate name.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
adc9a79f3f net: phy: print a number of phy that is not found
In case when several Ethernet ports are supported it's
convenient to see the number of phy that is not found.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
496191c7ab soc: keystone_serdes: generalize configuration mechanism
The cmu, comlane, lane configuration mechanism are similar for sub
systems as well such as PCI or sRIO, but they have different values
based on input clock and output bus rate. According to this compact
driver to simplify adding different configuration settings based
on clock and rate.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Hao Zhang
92a16c81f5 soc: keystone_serdes: generalize to be used by other sub systems
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Hao Zhang
95f74dad91 soc: keystone_serdes: enhance to use cmu/comlane/lane specific configurations
Enhance the driver to use cmu/comlane/lane specific configurations
instead of 1 big array of configuration.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
a43febde44 soc: keystone_serdes: create a separate SGMII SerDes driver
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.

Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Khoronzhuk, Ivan
497e9e0321 net: keystone_net: remove redundant code from keystone_net.c
Remove unused tx_send_loop variable.

Removes duplicated get_link_status() call from the
keystone2_eth_send_packet().

The emac_gigabit_enable() is called at opening Ethernet and there is no
need to enable it on sending each packet. So remove that call
from keystone2_eth_send_packet() as well.

The calling of power/clock up functions are mostly the responsibility
of SoC/board code, so move these functions to appropriate place.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Vitaly Andrianov
f077226610 net: keystone_net: increase MDIO clock frequency
With MAC_PHY sgmii configuration, u-boot checks PHY link status before
sending each packet. Increasing MDIO frequency increases overall tftp
speed. We set it to maximum 2.5MHz.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Khoronzhuk, Ivan
0935cac685 net: keystone_net: move header file from arch to ti-common
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Khoronzhuk, Ivan
e3114c9a06 net: keystone_net: add support for NETCP v1.5
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.

The port number is specific for each board so move this parameter to
configuration.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Hao Zhang
b2cfe32278 net: keystone_net: remove SoC specific emac_regs structure
This patch removes K2HK SOC specifc emac_regs structure, it uses
soc specific register offset to keep the network driver common across
all the Keystone II EVMs.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Khoronzhuk, Ivan
8347210a3f configs: ks2_evm: enable misc_init_r
Currently keystone has misc_init_r where all DSPS are turned off
by default. So enable this function.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Hao Zhang
345af53456 keystone2: k2l-evm: add board support
This patch adds Keystone II Lammar (K2L) EVM board support.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Hao Zhang
b66604fb66 keystone2: enable OSR clock domain for K2L SoC
This patches enables the On-chip Shared Ram clock domain for K2L SoC.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Hao Zhang
5ec66b140a ARM: keystone2: spl: move board specific code
The initialization of PLLs is a part of board specific code, so
move it appropriate places.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Hao Zhang
bc45d5729f keystone2: msmc: add MSMC cache coherency support for K2L SOC
This patch adds Keystone II Lamar (K2L) SoC specific definitions
to support MSMC cache coherency.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:05 -04:00
Hao Zhang
61d122583f keystone2: clock: add K2L clock definitions and commands
This patch adds clock definitions and commands to support Keystone II
K2L SOC.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Hao Zhang
c4995a8282 ARM: keystone2: add K2L device hardware definitions
This patch adds hardware definitions specific to Keystone II
Lamar (K2L) SoC.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Khoronzhuk, Ivan
529ce1eedf ARM: cmd_clock: generalize command usage description
The usage description of commands refers to headers of sources,
that is not correct. This patch is intended to fix it.
Also generalize code in order to reduce SoC dependent #ifdefs.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
WingMan Kwok
bc0e8d7c5d keystone: usb: add support of usb xhci
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Khoronzhuk, Ivan
9ea9021ac4 dma: keystone_nav: generalize driver usage
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.

The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Khoronzhuk, Ivan
ef4547176d dma: keystone_nav: move keystone_nav driver to driver/dma/
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.

This patch just move this driver to appropriate directory and
doesn't add any functional changes.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Khoronzhuk, Ivan
ed948e2959 keystone2: keystone_nav: don't use hard addresses in netcp_pktdma
Use definitions in netcp_pktdma instead direct addresses.
The definitions can be set specifically for SoC, so there
is no reason to check SoC type while initialization.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Khoronzhuk, Ivan
afa479cf66 keystone2: keystone_nav: don't use hard addresses in qm_config
Use definitions in qm_config. The definitions can be set specifically
for SoC, so there is no reason to check SoC type while initialization.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:04 -04:00
Stefan Roese
b2b8a6967a Makefile: Add CONFIG_BUILD_TARGET to automatically build an special image
Add target to build it automatically upon "make" / MAKEALL. This can/should
be set by board / cpu specific headers if a special U-Boot image is
required for this SoC / board.

E.g. used by Marvell Armada XP to automatically build the u-boot.kwb
target.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-23 09:59:21 -04:00
Stefan Roese
4acd2d24b6 tools: kwbimage: Add image version 1 support for Armada XP / 370
This patch integrates the Barebox version of this kwbimage.c file into
U-Boot. As this version supports the image version 1 type for the
Armada XP / 370 SoCs.

It was easier to integrate the existing and known to be working Barebox
source than to update the current U-Boot version to support this
v1 image header format. Now all Marvell MVEBU SoCs are supported:

Image type 0: Kirkwood & Dove
Image type 1: Armada 370 & Armada XP

Please note that the current v1 support has this restuction (same as
has Barebox version):

Not implemented: support for the register headers and secure headers
in v1 images

Tested on Marvell DB-78460-BP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
2014-10-23 09:59:21 -04:00
Stefan Roese
2afa331260 tools: Compile kwboot for Marvell Armada XP as those SoCs are now supported
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
2014-10-23 09:59:21 -04:00
Stefan Roese
84899e2db3 tools/kwboot: Sync with latest barebox version to support Armada XP
The barebox version of the kwboot tool has evolved a bit. To support
Armada XP and Dove. Additionally a few minor fixes have been applied.
So lets sync with the latest barebox version.

Please note that the main difference between both versions now is, that
the U-Boot version still supports the -p option, to dynamically patch
an image for UART boot mode. I didn't test it now though.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
2014-10-23 09:59:21 -04:00
Stefan Roese
1721fe6966 arm: kirkwood: Remove some dead code from cpu.c
All those functions removed with this patch are not accessed at all. So lets
remove them.

Signed-off-by: Stefan Roese <sr@denx.de>
2014-10-23 09:59:21 -04:00
Stefan Roese
a488483174 arm: armada-xp: Add basic support for the maxBCM board
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.

Signed-off-by: Stefan Roese <sr@denx.de>
2014-10-23 09:59:21 -04:00
Stefan Roese
dd580801aa arm: armada-xp: Add basic support for the Marvell DB-MV784MP-GP board
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
2014-10-23 09:59:21 -04:00