As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently Keystone2 Lamar evm (K2L) board is added, so update
Keystone2 readme file to have such one.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Lamar SoC uses the same keystone navigator.
Move queue numbers to common hardware file, as all Keystone2 SoCs
have the same ones.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but
the code tests 1GB DRAM configuration as if it is all present on one
chip select, and thus cannot see the full range of available memory.
Refactor the check to detect 1GB DRAM correctly.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Change the order in which GPIOs are toggled in SATA init sequence to
accomodate both SanDisk and Phison SSDs.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The scsi_init() function uses a GPIO so should request it. There is no
way to return an error here, and the request may be made multiple times,
so just ignore errors for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For now we won't want to mess with the existing configurations. Create a
new one which will enable device tree and driver model. Note that this
brings the device tree binary into u-boot-sunxi-with-spl.bin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These are from Linux 3.17-rc7 (commit fe82dcec). U-Boot only uses a small
portion of these, but we may as well have something to look forward to.
The total compiled size is about 25KB.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
$ make BOARD_felconfig
is more convenient than
$ make BOARD_defconfig
$ echo CONFIG_SPL_FEL=y >> .config
$ echo CONFIG_SPL_FEL=y >> spl/.config
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This was done automatically with the following bits of scripting.
The Kconfig choice content was generated with this script snippet:
for i in $(git grep -l CONFIG_ARCH_SUNXI configs/*) ; do
TARGET=$(sed -n -e 's/CONFIG_SYS_EXTRA_OPTIONS="\([^,"]\+\).*/\1/p' $i);
MACH=$(sed -n -e 's/.*CONFIG_\(MACH_SUN.I\)=./\1/p' $i)
echo "config TARGET_$TARGET"
echo " bool \"$TARGET\""
echo " depends on $MACH"
echo
done
defconfigs were updated with a sed script (t):
# Extract board from first entry of CONFIG_SYS_EXTRA_OPTIONS,
/^CONFIG_SYS_EXTRA_OPTIONS/ {
s/^\(CONFIG_SYS_EXTRA_OPTIONS="\)\([^,"]\+\),\?\(.*\)/\1\3\nCONFIG_TARGET_\2=y/;
# Print and delete first line (CONFIG_SYS_EXTRA_OPTIONS), leaving
# CONFIG_TARGET_<BOARD> in pattern space
P;D;
};
# Move CONFIG_TARGET_<BOARD> to hold space
/^CONFIG_TARGET/{h;n}
# Print CONFIG_TARGET_<BOARD> after CONFIG_MACH_<SOC> in either SPL or
# normal mode.
/^CONFIG_MACH/{p;g;p;n};
/^\+S:CONFIG_MACH/{p;g;s/^CONFIG_TARGET/+S:&/;p;n};
# Print any remaining lines normally
p;
Run as:
sed -i -n -f t $(git grep -l CONFIG_ARCH_SUNXI configs/*)
and then manually removing the one instance of CONFIG_SYS_EXTRA_OPTIONS="" from
Colombus_defconfig
board/sunxi/Makefile was updated with:
sed -e 's/^\(obj-\$(CONFIG_\)\(.*\)\().*+= dram_.*\)/\1TARGET_\2\3/g' board/sunxi/Makefile
and manually retabbing a few lines to line up again.
The board descriptions could certainly be improved.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This can now be configured via Kconfig, e.g. with:
$ make BOARD_defconfig
$ echo CONFIG_SPL_FEL=y >> .config
$ echo CONFIG_SPL_FEL=y >> spl/.config
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It's unfortunate that this needs to be present in both .config and spl/.config
since it makes it slightly hard to enable FEL mode for a regular defconfig. It
can be done with:
echo CONFIG_SPL_FEL=y >> .config
echo CONFIG_SPL_FEL=y >> spl/.config
Ideally only one of those would be needed.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now we have CONFIG_ARCH_SUNXI as the toplevel, CONFIG_MACH_SUN[45678]I as the
per-SoC option and leave CONFIG_TARGET_BLAH free for individual boards in the
future.
Done automatically with:
sed -i -e 's/TARGET_\(SUN[45678]I\)/MACH_\1/g' $(git grep -l TARGET_SUN[45678]I)
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And make TARGET_SUN[45678]I a choice variable under this.
configs updated with:
sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/*
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The defconfig for Ippo-q8h-v5 was incorrectly committed as
"Ippo_q8h". This patch renames it correctly, as well as
correct a typo in my name in the maintainers listing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
I realized that with v2014.10 u-boot is not starting up on
ppc4xx boards with CONFIG_SYS_GENERIC_BOARD set.
I bisected it down to this:
d54d7eb support blackfin board initialization in generic board_f
With
d29437a ppc: Make ppc4xx ready for CONFIG_SYS_GENERIC_BOARD
I set gd to a defined value for ppc4xx in cpu_init_f().
I did not realize that the gd struct has also to be memset()
to zero at this point.
But at least commit d54d7eb assumes it is:
@@ -516,11 +528,13 @@ static int reserve_malloc(void)
/* (permanently) allocate a Board Info struct */
static int reserve_board(void)
{
- gd->start_addr_sp -= sizeof(bd_t);
- gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
- memset(gd->bd, '\0', sizeof(bd_t));
- debug("Reserving %zu Bytes for Board Info at: %08lx\n",
- sizeof(bd_t), gd->start_addr_sp);
+ if (!gd->bd) {
+ gd->start_addr_sp -= sizeof(bd_t);
+ gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
+ memset(gd->bd, '\0', sizeof(bd_t));
+ debug("Reserving %zu Bytes for Board Info at: %08lx\n",
+ sizeof(bd_t), gd->start_addr_sp);
+ }
return 0;
}
#endif
This might also be an issue on other architectures, so maintainers should
check.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fix the kwimage tools for version 0 fileformat used for kirkwood
Tested on sheevaplug
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
* Escape use of - in description of -F.
* Fix line continuations in examples so that the continued lines are
also bold.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
These lines originate in Linux; it looks like Linux folks chose to
hide bunch of warnings reported by clang rather than fixing C code.
In U-boot, warnings are being fixed thanks to Jeroen's great efforts.
Let's stop suppressing clang warnings.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Defining CONFIG_SYS_TEXT_BASE in config.mk is very old style.
Create CONFIG_SYS_TEXT_BASE option in Kconfig, but let it
depend on CONFIG_SPARC because we do not want to disturb
the other architectures that still define CONFIG_SYS_TEXT_BASE
in their header files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
For now, all the SPARC boards in U-Boot are provided by Gaisler.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Remove arch/sparc/cpu/{leon2,leon3}/config.mk and move duplicated
defines of -fPIC to arch/sparc/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
The Board names in the board select menu were simply taken from the
board directory name by a conversion tool when switching to Kconfig.
Let's use more descriptive prompts taken from
include/configs/gr*.h and board/gaisler/*/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
R8A7791, R8A7793 and R8A7794 have same IP of USB controller.
This collect up address data of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
