This commit adds TVE base address for Allwinner H3 and H5 SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we added LPDDR3 support in the former patch, we need a set of timing
info to really enable it.
Add the timing info used by stock boot0.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some A64 boards (SoPine and Pinebook production batch) use LPDDR3 DRAM
chips.
Add support for LPDDR3 DRAM in the DesignWare-like DRAM controller code.
Real LPDDR3 chips' support is not added yet in this commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
As we have already support for the DesignWare DRAM controller and the
integrated DDR2 chip of V3s, let's enable the SPL support for V3s.
This patch also contains the default DRAM configuration for V3s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s features a DRAM controller like the on in H3, but with a
DDR2 DRAM.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s SoC features a co-packaged DDR2 DRAM chip, which needs its
timing param.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare-like DRAM code used to set the controller defaultly to
single rank mode, which makes it not able to detect the second rank.
Set the default value to dual rank, thus the rank detection code can
work and finally the rank setting will be the correct value.
Currently we know little about the dual-rank on R40, and the usage
of A15 address line seems to be breaking dual-rank support. The only R40
board currently available (Sinovoip Banana Pi M2 Ultra) uses A15 rather
than dual-rank, thus we cannot do research for it. So dual rank detection
is temporarily disabled on R40.
This change is tested on a Orange Pi One (H3, single rank), a Pine64+
2GiB version (A64, single rank) , a Pinebook early prototype with DDR3
(A64, dual rank) and a SoPine with some LPDDR3 patch (A64, dual CS pins
on one chip).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
DRAM chip varies, and one code cannot satisfy all DRAMs.
Add options to select a timing set.
Currently only DDR3-1333 (the original set) is added into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some DDR2 DRAM have only four banks, not eight.
Add code to detect this situation.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some Allwinner SoCs features a DesignWare-like controller with only 16
bit bus width.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare DRAM controller used by H3 and newer SoCs use a bit to
identify whether the DRAM is half-width.
As H3 itself come with 32-bit DRAM, the two modes of the bit used to be
named "MCTL_CR_32BIT" and "MCTL_CR_16BIT", but for SoCs with 16-bit DRAM
they're really 8-bit and 16-bit.
Rename the bit's macro, and also rename the variable name in
dram_sun8i_h3.c.
This commit do not add 16-bit DRAM controller support, but the support
will be introduced in next commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner SoCs after H3 (e.g. A64, H5, R40, V3s) uses a H3-like
DesignWare DRAM controller, which do not have official free DRAM
initialization code, but can use modified dram_sun8i_h3.c.
Add a invisible option for easier DRAM initialization code reuse.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This commit enables the RK3399 HDMI TX, which is very similar to the
one found on the RK3288. As requested by Simon, this splits the HDMI
driver into a SOC-specific portion (rk3399_hdmi.c, rk3288_hdmi.c) and
a common portion (rk_hdmi.c).
Note that the I2C communication for reading the EDID works well with
the default settings, but does not with the alternate settings used on
the RK3288... this configuration aspect is reflected by the driverdata
for the RK3399 driver.
Having some sort of DTS-based configuration for the regulator
dependencies would be nice for the future, but for now we simply use
lists of regulator names (also via driverdata) that we probe.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds a driver for the RK3399 VOPs capable and all the
necessary plumbing to feed the HDMI encoder. For the VOP-big, this
correctly tracks the ability to feed 10bit RGB data to the encoder.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To prepare for adding the RK3399 VOP driver (which shares most of its
registers and config logic with the RK3228 VOP), this change refactors
the driver and splits the RK3288-specific driver off.
The changes in detail are:
- introduces a data-structure for chip-specific drivers to register
features/callbacks with the common driver: at this time, this is
limited to a callback for setting the pin polarities (between the
VOP and the encoder modules) and a flag to signal 10bit RGB
capability
- refactors the probing of regulators into a helper function that
can take a list of regulator names to probe and autoset
- moves the priv data-structure into a (common) header file to be
used by the chip-specific drivers to provide base addresses to
the common driver
- uses a callback into the chip-specific driver to set pin polarities
(replacing the direct register accesses previously used)
- splits enabling the output (towards an encoder) into a separate
help function withint the common driver
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RK3288_TXCLK_DLY_ENA_GMAC_ENABLE, in GRF_SOC_CON3, is supposed to be bit
0xe and not 0xf. Otherwise, it is RGMII RX clock delayline enable and
introduces random delays and data lose.
This commit fixes the issue by replacing RK3288_TXCLK_DLY_ENA_GMAC_ENABLE
with the right shift.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds the DDR3-1866 timing via its own DTS and wires it up. This
(currently) is not the default timing for the RK3399-Q7 and should be
selected explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds the DDR3-1333 timing via its own DTS and wires it up. This
is not the default timing for the RK3399-Q7 and should be selected
explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
To better support different RAM timings (DDR3-1333 and DDR3-1866 are
assembly options for the RK3399-Q7), this refactors the DTS support
and renames the default DTS variant from rk3399-puma to
rk3399-puma-ddr1600:
- changes the rk3399-puma DTS into a board-specific DTSI by removing
the inclusion of the DRAM timings
- adds a new rk3399-puma-ddr1600.dts, which includes the (new) common
board DTSI and the DDR3-1600 timing DTSI
- wires this up from arch/arm/dts/Makefile and configs/puma-rk3399_defconfig
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Linux DTS for the RK3399-Q7 has moved with the times... resync
against it to ensure a consistent configuration.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit enables HDMI output in the DTS by adding the necessary
nodes to vopl/vopb and by adding the HDMI node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RV1108 is embedded with an ARM Cortex-A7 single core and a DSP core
from Rockchip. It is designed for varies application scenario such
as car DVR, sports DV, secure camera and UAV camera.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
defines the spl-payload to 256k (0x40000)
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, the on-module USB3 hub is held in reset at boot-up
to save power and needs to be woken up using GPIO4A3.
Note that this is not a negated reset-signal (due to a level shifter
being needed for this signal anyway), but a negated enable-signal:
to enable, we need to output LOW (i.e. 0)... so we mark this as an
ACTIVE_LOW signal.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the validation done for DDR3-1866 (i.e. 933 MHz bus clock), we
can now add the timings (rk3399-sdram-ddr3-1866.dtsi) for boards built
with the DDR3-1866 option.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399 is capable of driving DDR3 at 933MHz (i.e. DDR3-1866),
if the PCB layout permits and appropriate memory timings are used.
This changes the sanity checks to allow a DTS to request DDR3-1866
operation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Revise the loop watching for a timeout on obtaining a DRAM PHY lock to
clearly state a timeout in milliseconds and use get_timer (based on
the ARMv8 architected timer) to detect a timeout.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In rk3328, some function pin may have more than one choice, and muxed
with more than one IO, for example, the UART2 controller IO,
TX and RX, have 3 choice(setting in com_iomux):
- M0 which mux with GPIO1A0/GPIO1A1
- M1 which mux with GPIO2A0/GPIO2A1
- usb2phy which mux with USB2.0 DP/DM pin.
We should not decide which group to use in pinctrl driver,
for it may be different in different board, it should goes to board
file, and the pinctrl file should setting correct iomux depends on
the com_iomux value.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move GRF register bit definition into GRF header file, remove
'GRF_' prefix and add 'GPIOmXn_' as prefix for bit meaning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-Boot prefer to use MASKs with SHIFT embeded, clean the Macro
definition in grf header file and pinctrl driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- hclk/pclk_div range should use '<=' instead of '<'
- use GPLL for pd_bus clock source
- pd_bus HCLK/PCLK clock rate should not bigger than ACLK
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Embeded the shift in mask MACRO definition in cru header file
and clock driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The RK3368 is an octa-core Cortex-A53 SoC from Rockchip.
This adds basic support to chain-load U-Boot from Rockchip's
miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver to support iomux setup for the most commonly
used peripherals on rk3368.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver to setup the various PLLs and peripheral
clocks on the RK3368.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some host like SD and eMMC may use DMA to transter data to SRAM,
set memory to non-secure to make sure the address can be accessed.
The security of SRAM in OS suppose to initialized in ATF bl31, and
the SPL is before the bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The branch instruction only has an 11-bit relative target address, which
is sometimes not enough.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Rather than change asm files that come from Linux, add the symbols
to Kconfig. Since one of the symbols is for thumb2 builds, make
CPU_V7M always select them.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Mark explicitly bss sections to not be loaded at
run time.
The similar patch was done in past by:
"Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections"
(sha1: 64134f0112)
The problem is related to latest toolchain added to Xilinx
v2017.1 design tools where jtag loader is trying to access
ununitialized memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for calling poweroff in case of psci is wired.
Based on the same solution as is used for reset.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move all logic in to fwcall.c as other ARMs implement poweroff
via PMIC]
Signed-off-by: Tom Rini <trini@konsulko.com>
The dtb blob section must always be present in the resulting image.
Either if OF_EMBEDED is used or if unit tests include dtb blobs.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Instead, use
the asm/hardware.h header to provide the required declarations, and drop
the common.h changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These declarations should not be in common. Remove those that are not
needed and move the others to an arch-specific location.
Signed-off-by: Simon Glass <sjg@chromium.org>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present common.h includes various ARM-specific headers. In preparation
for dropping this, add a few explicit declarations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than including this arch-specific header file in common.h, include
it from within arm's u-boot.h header.
Also drop the comment about something to be fixed. It has been there
forever and it is not clear what it means.
Signed-off-by: Simon Glass <sjg@chromium.org>
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than have a long and if check in the Makefile, mark the default
lowlevel_init function as weak (as we do on armv8) so that SoCs can
override it if needed, and it will still be discarded if unused.
Provide a weak s_init as well to allow for this to link and be
discarded.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the LDO's nodes that taken from Linux Kernel.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Change the nodes relevant to mmc/sd for using DM.
compatible are also changed to each SoCs.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: Tom Rini <trini@konsulko.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Loading PPA in SPL puts the rest of U-Boot (including RAM version
loaded later) in EL2 with MMU and cache enabled. Once PPA is loaded,
PSCI is available.
Signed-off-by: York Sun <york.sun@nxp.com>
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: York Sun <york.sun@nxp.com>
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC,
but uses Cortex-A53 cores instead.
So move the shared cpu based and peripherals nodes into
sun50i-h5.dtsi so, that it can shared among the sun50i-h5
board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.
Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Linux device tree for the Allwinner A64 SoC has changed a lot since
the U-Boot version was merged.
Let's replace the current DT with a exact copy of the Linux one as of:
commit c6778ff813d2ca3e3c8733c87dc8b6831a64578b
Merge: 0ff4c01 3c0e3abd
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue May 9 10:07:33 2017 -0700
This is the DT used in Linux 4.12-rc1.
Since U-Boot has an Ethernet driver (while Linux does not yet), we
provide the required DT nodes for it in an ...-u-boot.dtsi file, to both
mark them as U-Boot specific and to allow easier upgrading once Linux gets
the driver and its own binding later.
Compared to the existing Ethernet DT nodes we just slightly tweak the clock
and reset nodes in there to match the new bindings used by Linux for those.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce the imx_set_perclk() function to make it possible to set the
PER clocks.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
imx_get_perclk() used the AHB clock as the clock source for all PER
clocks, but the USB PLL output can also be a PER clock source if the
corresponding PER CLK MUX bit is set in CCM.MCR.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
There is no dedicated reset signal wired up for the MX6QDL thus if the
bootloader enables the link we need some special handling to get the core
back into a state where it is safe to touch it for configuration.
While there has been some special handling in the Linux kernel to do this,
it was removed in 4.11 thus we need to do it properly in the bootloader
and therefore without this if you enable PCI in the bootloader you will hang
while booting the 4.11 kernel.
This puts the PCIe controller back into a safe state for the kernel driver
before launching the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.
Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The dram_init and dram_init_banksize functions were using a board
specific implementation for decoding the memory banks from the fdt.
This change makes the dram_init* functions use a generic implementation
of decoding and populating memory bank and size data.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the mvpp2 port 0 usage on the Armada 7k DB by setting
the correct PHY type (KR / SFI) for the COMPHY driver and enabling the
ethernet0 device node in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Start to populate the device tree of the Armada 37xx with the pincontrol
configuration used on the board providing a dts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Add the nodes for the two pin controller present in the Armada 37xx SoCs.
Initially the node was named gpio1 using the same name that for the
register range in the datasheet. However renaming it pinctr_nb (nb for
North Bridge) makes more sens.
Minor changes for U-Boot because of the slightly different dts version
done by Stefan Roese.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Update the NanoPi Neo device tree file to use the NanoPi dtsi.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HDMIDETECT
Note that we cannot do 'default y if VIDEO' because this option is only
enabled for a small subset of mx6 boards. Also this command is is not a
great implementation (it doesn't use driver model).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_ESBC_VALIDATE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
The IICDVFS(I2C) set in r8a7796.h is common in rcar-gen3.
This moves CONFIG_SYS_I2C_SH_BASE0 in rcar-gen3-base.h.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Salvator-X can have both H3 and M3 CPU on it, drop the
select R8A7795 to allow both configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7796 r1.1 reports itself as r2.0 , add quirk into the
PRR code to fix this report.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add entry for the R8A7796 RCar M3 SoC into the CPU info table.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add entry for the R8A7795 RCar H3 SoC into the CPU info table.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This Kconfig option is not used on any board, so drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the R8A7796 PFC and GPIO tables from the latest 3.5.3 release
from Renesas .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Sync the PFC and GPIO tables with the latest 3.5.3 release from
Renesas . This adds ES2.0 support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update Kconfig and Makefile to enable Arria 10.
Clean up Makefile and sorting *.o alphanumerically.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add system manager register struct and macros for Arria 10.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure misc driver in the preparation to support A10.
Move the Gen5 specific code to gen5 file.
Change all uint32_t_to u32.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure system manager in the preparation to support A10.
No functional change.
Change uint32_t to u32.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure reset manager driver in the preparation to support A10.
Move the Gen5 specific code to gen5 files.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure clock manager driver in the preparation to support A10.
Move the Gen5 specific code to _gen5 files.
- Change all uint32_t to u32 and change to use macro BIT(n) for bit shift.
- Check return value from wait_for_bit(). So change return type to int for
cm_write_with_phase() and cm_basic_init().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Drop the unneeded code. lib/time.c use timebase_l/h.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This patch updates the mksunxiboot tool to optionally add
the default device tree name string to the SPL header. This
information can be used by the firmware upgrade tools to
protect users from harming themselves by trying to upgrade
to an incompatible bootloader.
The primary use case here is a non-removable bootable media
(such as NAND, eMMC or SPI flash), which already may have
a properly working, but a little bit outdated bootloader
installed. For example, the user may download or build a
new U-Boot image for "Cubieboard", and then attemept to
install it on a "Cubieboard2" hardware by mistake as a
replacement for the already existing bootloader. If this
happens, the flash programming tool can identify this
problem and warn the user.
The size of the SPL header is also increased from 64 bytes
to 96 bytes to provide enough space for the device tree name
string.
[Andre: split patch to remove OF_LIST hash feature]
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The generic ARMv8 assembly code contains routines for setting up
a CCN interconnect, though the Freescale SoCs are the only user.
Link this code only for Freescale targets, this saves some precious
bytes in the chronically tight SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Not every SoC needs to set up the GIC interrupt controller, so link
think code only when the respective config option is set.
This shaves off some bytes from the SPL code size.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When booting from ARM Trusted Firmware, U-Boot runs in EL1-NS.
The boot flow is as follows:
BL1 -> BL2 -> BL31 -> BL33 (i.e. U-Boot)
This boot sequence works fine for LD11 SoC (Cortex-A53), but LD20
SoC (Cortex-A72) hangs in U-Boot. The solution I found is to
read sctlr_el1 and write back the value as-is. This should be
no effect, but surprisingly fixes the problem for LD20 to boot.
I do not know why.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Newer SoCs use same TV encoder unit. Split it out so it can be reused
with new DM video driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The symbol CONFIG_OMAP_VC_I2C_HS_MCODE always uses the default value.
Restructure the comment and code such that if a need arises later to use
another value we can address this then.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot. select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead. With that
changed we can drop all defines of CONFIG_OMAP. While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SMPEN bit is located in the cpuectlr_el1 register and not the
cpuactlr_el1 register. Adjust the comment accordingly and also fix
a spelling error.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
CC: York Sun <york.sun@nxp.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change tbu/l type to unsigned int.
>From the timer file for arm,
"(((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;" is used,
This piece code is based on tbu/tbl is 32bits, so change the type to
unsigned int.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The variable grf is only referenced if EARLY_DEBUG is defined so move the
declaration to be under the existing guard.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For early debug, the following configs needs to be enabled:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_BASE=0x44e09000
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For early debug, the following configs needs to be enabled:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y
For DRA7xx:
CONFIG_DEBUG_UART_BASE=0x4806a000
For AM57xx:
CONFIG_DEBUG_UART_BASE=0x48020000
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:
MPU values for PG 2.0 and later(Package ZCZ and ZCE):
-------------------------------------------------------
| | ZCZ | ZCE |
|-------------------------------------------------------|
| | VDD[V] | ARM [MHz] | VDD[V] | ARM [MHz] |
|-------|----------|------------|----------|------------|
| NITRO | 1.325 | 1000 | NA | NA |
|-------|----------|------------|----------|------------|
| TURBO | 1.26 | 800 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP120 | 1.20 | 720 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP100 | 1.10 | 600 | 1.10 | 600 |
|-------|----------|------------|----------|------------|
| OPP50 | 0.95 | 300 | 0.95 | 300 |
-------------------------------------------------------
There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.
[1] http://www.ti.com/lit/ds/symlink/am3356.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This configuration should be valid for all F7 family devices in general.
Here is the regions info:
- Region0 : 4GB : cacheable & executable.
- Region1 : 512MB : text area : strogly ordered & executable.
- Region2 : 512MB : peripherals : device memory & non-executable.
- Region3 : 512MB : peripherals : device memory & non-executable.
- Region4 : 512MB : cortexM area: strongly ordered & non-executable.
Higher region number overrides the lower region configuration.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Cortex-M archs support option memory protection unit (MPU). MPU is used
to set the memory types, attributes, access permissions for different regions,
cache policies of the device.
e.g. using MPU it is possible to configure memory region as device memory
or strongly ordered, memory attributes like execute never, cache policies
like write-back or write-through.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Data cache memory needs to be disabled before handing over control to
linux kernel. This patch populates the cleanup_before_linux stub.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Add functionality to flush & invalidate all the dcache using the
prototype declared in common header file.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add dummy functions for the not-enabled case]
Signed-off-by: Tom Rini <trini@konsulko.com>
am335x_evm SPL is very close to its limit in SRAM space.
Switch to use tiny printf to reclaim some size.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
No reason to use a separate load script for am33xx than using
omap-common load script.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support for fdt fixup to update the
memory node in device tree for falcon boot.
This is needed for single stage or falcon
bootmode, to pass memory configuration to
kernel through DT memory node.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Declare the size of ddr very early in spl, so that this can be
used to enable cache.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
