Enable all types of non-secure access to PFE block registers.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SoC specific PFE macros are defined and structure ccsr_scfg
is updated with members defined for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Layerscape Gen2 SoC supports GPIO registers to control GPIO
signals. Adding support of GPIO structure to access GPIO
registers.
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h
as all defines or enums are no more used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For STM32F4 and F7 SoCx family, a specific stm32.h file exists.
Some common defines are duplicated or even unused in each of
these stm32.h.
Factorize all common definition in arch/arm/include/asm/stm32f.h and keep
specific definitions in each arch/arm/include/asm/arch-stm32fx/stm32.h.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Instead to have 3 identical gpio.h for all STM32 SoCs,
migrate them in one file in include/asm.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
fmc.h file is no more used, remove it.
All FMC related defines are declared in drivers/ram/stm32_sdram.c
which is common to all STM32 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
commit ed286bc80e ("imx: hab: Check if CSF is valid before authenticating
image") makes use of "__packed" as a prefix to the "struct hab_hdr"
declaration.
With my compiler "gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)" we
get:
./arch/arm/include/asm/mach-imx/hab.h:42:25: error: expected ‘=’, ‘,’, ‘;’,
‘asm’ or ‘__attribute__’ before ‘{’ token
struct __packed hab_hdr {
Fix this problem by including <linux/compiler.h>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
We should take the MX6DP and MX6QP options in consideration
in the I2C_PADS_INFO macro.
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We should take the MX6DP and MX6QP options in consideration
when defining imx_iomux_v3_setup_pad().
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
SION bit should be used in the situation that we need
to read back the value of a pin and should not be set by
default macro.
We get some malfunction as raised by following thread
https://www.spinics.net/lists/linux-usb/msg162574.html
As reported by this application note:
https://www.nxp.com/docs/en/application-note/AN5078.pdf
The software input on (SION) bit is an option to force an input
path to be active regardless of the value driven by the
corresponding module. It is used when the nature direction
of a pin depending on selected alternative function is an output,
but it is needed to read the real logic value on a pin.
The SION bit can be used in:
• Loopback: the module of a selected alternative function drives
the pad and also receives the pad value as an input
• GPIO capture: the module of a selected alternative function
drives the pin and the value is captured by the GPIO
SION bit is not necessary when the pin is configured as a peripheral
apart specific silicon bug. If an application needs to have this
set, this should be done in board file or in dts file
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Include i.MX8M in lcdif register layout map.
Also included i.MX7ULP in this patch, since share same with i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Move i.MX6/7 bootaux code to imx_bootaux.c.
The i.MX6/7 has different src layout, so define M4 reg offset
to ease the cleanup. Redefine the M4 related BIT for share
common code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add SiP (Silicon Provider) services function to issue
SMC call to Arm Trusted Firmware.
More SiP information could be found in
https://github.com/ARM-software/arm-trusted-firmware/blob/master/
docs/arm-sip-service.rst
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add clock driver to support i.MX8M.
There are two kind PLLs, FRAC pll and SSCG pll. ROM already
configured SYS PLL1/2, we only need to configure the output.
ocotp/i2c/pll decoding and configuration/usdhc/lcdif/dram pll/
enet clock are configured in the code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
