Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of memory. This configuration
has only required nand flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the SDRAM_BASE and SDRAM_SIZE as it can now get these
details from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch updates the ram_base to store the start address of
the first bank DRAM and the use this ram_base to calculate ram_top
properly. This patch fixes the erroneous calculation of ram_top
incase of non zero ram start address.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
XILINX_SPI_FLASH_BASEADDR logic has been converted to DM that's why
there is no reason to depend on this address anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog can be started before probe and u-boot should just take control
over it. That's why do not stop watchdog in probe to cover cases where
watchdog can expire before probe and start.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added support of mmio read and write commands. These commands
can be used to read and write registers from the u-boot command line.
It can be useful in debugging.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable led support for boards which have "gpio-leds" node.
And also for microblaze which is converted to DM_GPIO now.
Tested on zcu100.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
IP itself has no reg/no bit which can be used for this functionality.
Add this note to the driver to make sure that none will be asking for
that. Current method is to setup 1s timeout and hang() which is done via
wdt_expire_now().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is only one chipselect on each connector.
Define it directly in board dts file.
There should be an option to use more chipselects via gpios.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx Axi wdt driver conversion to driver model & Kconfig update
for the same.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should support watchdog reset so that WATCHDOG_RESET will function
properly.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These macros are not required anymore. These will be taken from
configuration file.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed zynqmp command to handle subcommands with
U_BOOT_CMD_MKENT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling GPIO_DM support to have an option to use this
driver together with zynq gpio driver.
!DM part is kept there till Microblaze is cleanup which will be done
hopefully soon.
Just a note:
There is no reason to initialize uc-priv->name because it is completely
unused.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is storing reset vector at address 0x0.
It means soft reset can be done by just jumping to this address.
This code was in platform code but sysreset interface is providing
enough capabilities to have more options how to reset the system. It can
go from gpio reset through watchdog reset till soft reset.
The driver has not compatible string because this is cpu specific and DM
core is not able to detect compatible string in DT root that's why this
driver will be instantiated from platform code by calling
device_bind_driver(gd->dm_root, "mb_soft_reset", "reset_soft",
NULL);
It should be bind as the last reset method to ensure that hw reset is
called before this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux kernel has binding for gpio-restart node.
This patch is adding basic support without supporting any optional
properties.
This driver was tested on Microblaze system where gpio is connected to
SoC reset logic.
Output value is handled via gpios cells values.
In gpio_reboot_request() set_value is writing 1 because
dm_gpio_set_value() is capable to changing it when it is ACTIVE_LOW.
...
if (desc->flags & GPIOD_ACTIVE_LOW)
value = !value;
...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same change as was done for zynqmp with this description:
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0= &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
<zynqmp example removed>
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0 = &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
dm tree fragment for above configuration with patch applied:
ZynqMP> dm tree
Class index Probed Driver Name
-----------------------------------------
...
watchdog 0 [ ] cdns_wdt | |-- watchdog@ff150000
watchdog 1 [ + ] cdns_wdt | `-- watchdog@fd4d0000
...
dm uclass fragment:
ZynqMP> dm uclass
...
uclass 75: watchdog
0 watchdog@ff150000 @ 7df02f40, seq -1, (req 1)
1 * watchdog@fd4d0000 @ 7df02ff0, seq 0, (req 0)
...
It is visible that index 1 is IP with seq 0 which means that FPD
watchdog (@fd4d0000) is in DT below LPD watchdog (@ff150000).
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There should be proper bank name setup to distinguish between different
gpio drivers. Use dev->name for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Timer needs to be converted to DM but as of now it can't be called so
early because intc controller is not ready. Call it later in board_r.c.
Before this patch timer_init is called twice which is wrong.
The patch is blocking initialization before relocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove bogus zynq_gpio_getplat_data() and read driver data directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate gpio ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate sysreset ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_MP was added to Kconfig with enabling CONFIG_DEFINE_TCM_OCM_MMAP=y
for zynqmp boards. This option is enabled by default that's why it
shouldn't be in defconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Relocate watchdog ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
uclass name is used by dev_read_alias_seq which return seq number when
aliases are used.
Code fragment:
168 int dev_read_alias_seq(struct udevice *dev, int *devnump)
169 {
170 ofnode node = dev_ofnode(dev);
171 const char *uc_name = dev->uclass->uc_drv->name;
172 int ret;
173
174 if (ofnode_is_np(node)) {
175 ret = of_alias_get_id(ofnode_to_np(node), uc_name);
Also this patch enables DM_UC_FLAG_SEQ_ALIAS to be in sync with Linux
which is also using watchdog name for watchdog aliases.
drivers/watchdog/watchdog_core.c:215:
ret = of_alias_get_id(wdd->parent->of_node, "watchdog");
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
sysreset uclass have own do_reset function which should be used instead
of board/platform specific.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason not to use default ioremap/iounmap io functions.
The patch remove Microblaze macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.
Platform data is created when the device is bound, and survives
probe/remove cycles.
Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."
Based on description the driver needs to be switch to use platdata
instead of priv.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver supports only one instance of usb keyboard.
Remove the first dependency on generic usbkbd DEVNAME.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixed the same if/else part error by adding the required
source select on the basis of is_pre_src check.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to define default option for this macro which is
already done in common/cli_hush.c.
86 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
87 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
88 #endif
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
command_ret_t enum contains 3 return values but only two are handled
now. Extend cmd_process_error() and handle CMD_RET_USAGE separately.
These commands are affected by this change.
cmd/demo.c
cmd/efi.c
cmd/gpio.c
cmd/qfw.c
cmd/x86/fsp.c
test/dm/cmd_dm.c
And scripts shouldn't be affected because return value is not 0. But
every command implementation can choose what it is correct to pass.
I would expect that RET_USAGE is called when parameters are not
correctly passed (have incorrect value, missing parameters)
and RET_FAILURE when correct parameters are passed but command fails.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
Enable ums command for zcu100 to enable mass storage gadget.
Tested with ums 0 mmc 0 (for SD) and ums 0 usb 0 (for USB flashdisk).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
The device tree change was also submitted to the Linux Kernel and
has already been queued up for 4.19.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
