Instead of waiting for empty FIFO condition before writing a
character, wait for non-full FIFO condition.
This helps in saving several tens of milliseconds during boot
(depending verbosity).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
The u-boot console may show some corrupted characters when
printing in board_init() due to reset or baudrate change
of the UART (probe) before the TX FIFO has been completely
drained.
To fix this issue, and in case UART is still running, we now
try to flush the FIFO before proceeding to UART reinitialization.
For this we're waiting for Transmitter Complete bit, indicating
that the FIFO and the shift register are empty.
flushing has a 4ms timeout guard, which is normally more than
enough to consume the FIFO @ low baudrate (9600bps).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add the board detection mechanism to be able to support
the 2GB variant.
Based on the code from TechNexion U-Boot downstream tree.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add aliases for the RTCs on the board and on the SoC. This ensures that
the primary RTC is always the one on the board that has a buffered supply
and maximum accuracy.
This is a direct port of the pending commit from linux-next.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The i.MX 8M Mini SoC does incorporate an additional M-Core. To be able
to load it with a firmware, enable bootaux command as other Toradex
modules also have it enabled to be consistent.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
When an I2C clock is enabled inside enable_i2c_clk() the clock rate is
configured as PLL_SYS_MAIN_120M_CLK / 2 = 60MHz.
Currently, the I2C clock is retrieved from I2C1_CLK_ROOT, which
may not be the one that was enabled.
As there is no clock driver for the imx7d, it is better to return 60MHz
for the I2C clock.
This provides a workaround for the imx7d-pico board, where I2C4 is
connected to the PMIC.
With this change, it is possible to convert the imx7d-pico board
to DM_I2C and DM_PMIC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 56c2dbdaba ("imx: bootaux: cleanup code") introduces the
following LTO related warning:
"
arch/arm/mach-imx/imx_bootaux.c:24:31: warning: type of ‘hostmap’ does not match original declaration [-Wlto-type-mismatch]
24 | const __weak struct rproc_att hostmap[] = { };
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: array types have different bounds
1590 | const struct rproc_att hostmap[] = {
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: ‘hostmap’ was previously declared here
../aarch64-linux-gnu/bin/ld: warning: u-boot has a LOAD segment with RWX permissions
"
This is because the weak empty array of structures "hostmap" is eventually
replaced by non-empty array of structures with different number of elements.
Fix this by avoiding weak variable size array, instead use a weak function
which returns single pointer to the array.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are no CONFIG_{TOOLS_,SPL_,TPL_,}IMX8M macros, nor is there one for
ARM64. Use plain IS_ENABLED(CONFIG_IMX8M) and IS_ENABLED(CONFIG_ARM64) to
avoid expanding the {TOOLS_,SPL_,TPL_,} part.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Pull common.c into common subdirectory of the board file,
since this code can be reused by other Data Modul SBCs.
Drop the include of lpddr4_timing.h, which is unneeded.
Signed-off-by: Marek Vasut <marex@denx.de>
The icache is enabled in common architecture code since commit:
2fa763baa1 ("ARM: imx: Enable instruction cache early on on i.MX8M")
Drop the board side duplicate code.
Signed-off-by: Marek Vasut <marex@denx.de>
Originally, the mmc aliases node was present in imx6qdl-sabresd.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc1.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Reported-by: Carlos Rafael Giani <dv@pseudoterminal.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
This reinstates change from commit:
e26d0152d6 ("ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables")
which has been dropped in commit:
b0a284a7c9 ("imx: move get_boot_device to common file")
Fixes: b0a284a7c9 ("imx: move get_boot_device to common file")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The PCA9450 reset configuration can now be performed by the PCA9450 PMIC
driver itself, remove the hard-coded variant from board code and let the
PMIC driver perform this task using one-liner:
```
$ sed -i '/set WDOG_B_CFG to cold reset/,+2 d' $(git grep -l PCA9450_RESET_CTRL.*0xA1 board/)
```
Venice and i.MX93 EVK required slight manual fix up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The handle "fd" was created in imx8image.c:249 by calling the "fopen"
function and is lost in imx8image.c:282.
Should close the 'fd' file descriptor before exiting the
parse_cfg_file(image_t *param_stack, char *name) function.
Fixes: a2b96ece5b ("tools: add i.MX8/8X image support")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The handle "fd" was created in imx8mimage.c:178 by calling
the "fopen" function and is lost in imx8mimage.c:210.
Should close the 'fd' file descriptor before exiting
the parse_cfg_file(char *name) function.
Fixes: 6609c2663c ("tools: add i.MX8M image support")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
The struct dcd_v1_t is initialized to MAX_HW_CFG_SIZE_V1 (60)
structs 'dcd_type_addr_data_t', so the indexes to use on its elements
are [0,59]. But on line 478, the variable 'length' can take on the value
60, which applies to array overflow: cd_v1->addr_data[length].type Thus,
it is necessary to tighten the check on the 'size' variable on line 463.
Fixes: 0b0c6af387 ("Prepare v2020.01")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
This reverts commit f5315dd629.
[why]
TPL is not mandatory for not all Rockchip SoCs, some SoCs like
RK356x, and RK3588 still use mainline u-boot without TPL as
their ddr init programs are accessed via binaries provided by
Rockchip instead of ddr source code.
Marking TPL build makes it not able to build u-boot.itb on
RK356x targets so revert this so that it can build an SPL build
that would support all across Rockchip platforms.
Suggested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Tested-by: Anand Moon <linux.amoon@gmail.com> # CM3
Add M4 boot environment functions for reference.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Set i.MX auxiliary core memory base and size.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the distro config env memory layout for the Apalis iMX8 aka
QuadMax:
- kernel_comp_addr_r=0xf0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Basic idea of memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout"). However, moved past
any reserved areas to avoid any kind of conflicts.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Remove obsolete net USB start.
While at it also add a comment about enabling distro-boot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Remove obsolete SDHC related config defines. Nowadays, all SDHC related
hardware configuration comes from the device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The DDR calibration tool for i.MX8M currently produces 3732 MTps rate in
lpddr4_timing.c , while the PHY code expects 3733 MTps rate. Support both
variants to avoid surprises where the system fails to boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Add pinctrl's for high speed eMMC and MMC cards.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Remove a duplicate of weak board_phy_config() implementation
in drivers/net/phy/phy.c.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The distroboot script system scans boot_scripts variable and
try to find and use to boot each script name mentioned there.
Setting global variable "script" breaks this general mechanism
of searching and running a distro boot script.
Remove global variables "script" to fix working the general
distro boot script mechanism.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
There is no "apply" command enabled for "fdt".
Enable "apply" command to allow overlays to be applied.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Set the boot delay to one second.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This provides correct system prompt for U-Boot console.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Display build info with information about the version of SCFW, SECO and
TF-A (ATF).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light GPIO Apalis BKL1 before booting Linux.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Implement PCB version and SoC variant handling which automatically loads
the correct device tree for the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In case the CONFIG_IMX8M_LPDDR4 and CONFIG_IMX8M_DDR4 options are both
disabled (i. e. BSH boards), binmain fails because DDR4 bin files are
missing.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
First, to quote the author:
This series adds support for the PCIe controller found on Apple M1 and
M2 machines and enables support for PCIe XHCI controllers. This makes
the type-A USB ports on the M1 Mac mini work. Since the use of Apples
DART IOMMU is mandatory (these PCIe DARTs don't support bypass mode),
this adds DMA mapping operations to the IOMMU uclass and implements
them for the Apple DART. It modifies the XHCI driver code to go map
DMA buffers through the IOMMU if there is one. Since the M1 Mac mini
now has two types of XHCI controllers with different number of ports
(2 for the DWC3 controllers, 8 for the Fresco Logic PCIe controller)
this uncovered an issue in with the way the hub descriptor is
implemented in the XHCI driver.
Second, Mark also fixes some Apple-specific instances of
CONFIG_IS_ENABLED that should be IS_ENABLED.
Documentation:
* Improve the sl-mx8mm documenation
* Clean up README, move some section to HTML
* Man-pages for the mtime and sleep command
* Description of reducible builds
* Document dynamic event handlers
UEFI:
* Support scrolling in eficonfig command
Other:
* fix mtest on 64 bit systems
-----BEGIN PGP SIGNATURE-----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=FY9O
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2023-04-rc1-3
Documentation:
* Improve the sl-mx8mm documenation
* Clean up README, move some section to HTML
* Man-pages for the mtime and sleep command
* Description of reducible builds
* Document dynamic event handlers
UEFI:
* Support scrolling in eficonfig command
Other:
* fix mtest on 64 bit systems
When a system has multiple XHCI controllers, some of the
properties described in the descriptor of the root hub (such as
the number of ports) might differ between controllers. Fix this
by switching from a single global hub descriptor to a hub
descriptor per controller.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some Apple Silicon machines have a PCIe XHCI controller in additon
to the DWC3 controllers integrated on the SoC. On the Mac mini
the Type-A ports are handled by this PCIe controller. Enabling
it allows the use of these ports in U-Boot.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This driver supports the PCIe controller on the Apple M1 and
M2 SoCs. The code is adapted from the Linux driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
