Set CLK01 and CLK02 to 24MHz and enable it in CCM_CCOSR register.
This clock is used by both the audio codec (CLKO1) and by the CSI camera
(CLKO2) and is expected to be 24MHz.
Despite the wrong 16.5MHz there was no real issue because of the wrong
frequency since Linux reconfigures the clocks afterward, however this
was triggering an issue with noise coming from the SGTL5000 audio codec.
The problem is that the SGTL5000 does not have a reset pin and after it
is configured if the input MCLK clock is disabled it produces a constant
noise on its output, this was happening on software reboot.
Forcing the clock to be enabled in U-Boot prevent the problem by making
sure that the clock is always available, without this change as soon as
Linux was changing the clock tree (setting clk_out_sel=1 without setting
clko2_en=1) the noise would start till the actual clock was enabled
(clko2_en=1) during the SGTL5000 driver probe.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Commit e42dad4168 ("sunxi: use boot source for determining environment
location") changed our implementation of env_get_location() and enabled
it for every board, even those without MMC support (like the C.H.I.P.
boards). However the default fallback location of ENVL_FAT requires MMC
support compiled in, so the board hangs when trying to initially load
the environment.
Change the algorithm to only return configured environment locations,
and improve the fallback algorithm on the way.
The env_init() routine calling this function here does not behave well
if the return value is ENVL_UNKNOWN on the very first call: it will make
U-Boot proper silently hang very early.
Work around this issue by making sure we return some configured (dummy)
environment location when prio is 0. This for instance happens when
booting via FEL.
This fixes U-Boot loading on the C.H.I.P. boards.
Fixes: e42dad4168 ("sunxi: use boot source for determining environment location")
Reported-by: Chris Morgan <macroalpha82@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix FEL boot case by not returning ENVL_UNKNOWN when prio==0]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The origin of this patch is the breaking of am335x-hs boot
due to commit e41651fffd ("dm: Support parent devices with of-platdata")
HS boards have less SRAM for SPL and so this commit increased memory usage beyond am335x limit.
This commit added 10 driver binding pass and am335x boot only if one pass is done.
SPL try to do more than one pass due to eth_cpsw failing.
Since HS SPL does not need network (and NET is already disabled in config),
the easiest fix is to "remove" eth_cpsw from SPL by testing if NET is enabled.
Signed-off-by: Corentin LABBE <clabbe@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Andrew Davis <afd@ti.com>
SoM revision 1.9 has replaced the ar8035 phy address 0 with an adin1300
at address 1. Because early SoMs had a hardware flaw, the ar8035 can
also appear at address 4 - making it a total of 3 phy nodes in the DTB.
To avoid confusing Linux with probe errors, fixup the dtb to only enable
the phy node that is detected at runtime.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Add the new Apalis iMX8 product variant
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
the only difference to the product
0037 Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
is the 8gb of RAM. Toradex strategy to choose the correct RAM timing in
SCFW is by fuses in the user area telling which RAM timing to load.
This commit makes use of this information to set the correct size of
the RAM and therefore distinguish between the new 0067 and 0037 product
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
This module is identical to its 4GB counterpart
0037: Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
except for the RAM size.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use device tree to set MAC address of the Ethernet chip.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable OF_HAS_PRIOR_STAGE for ae350 boards with OF_BOARD
Fixes: 239d22c795 ("fdt: Enable OF_HAS_PRIOR_STAGE for most boards with OF_BOARD")
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
Currently, selecting UART0_PORT_F entirely disables MMC support on sunxi
platforms. But this is a bigger hammer then needed. Muxing UART0 to the
pins on port F only causes a conflict with MMC0, so minimize the impact
by specifically skipping MMC0 init. We can continue to use MMC1/2 if
those are enabled.
Let's also remove the preprocessor check while refacting this function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert the board to DM I2C and DM RTC. This leads to removal of board
side iomuxc configuration, which is now done using pin control driver,
and conversion of board side legacy I2C accessors to DM ones.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Before this commit device tree selection could rely solely on
differentiating the iMX6 processor variant Q and DL. After adding two new
carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs
makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02,
dhcom-picoitx or dhcom-pdk2) at compile time using
CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the preloader_console_init() call after spl_early_init() to avoid
board hang in SPL.
While at it remove explicit in-code console/debug UART pinmuxing (uart1
and its pinmuxing are already marked as u-boot,dm-spl via device tree).
Fixes: 4551e18987 ("configs: verdin-imx8mm: verdin-imx8mp: enable dm serial")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
implement get f/w version api.
print ele f/w version in spl.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
pinctrl_wdog as u-boot,dm-spl already marked in imx8mm-verdin-u-boot.dtsi,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 61cf225053 ("board: gateworks: gw_ventana: use comomn GSC driver")
moved to the common GSC driver and moved remaining board-specific
functions to eeprom.c. The functions in gsc.c are no longer used and it
was removed from the Makefile but the file itself was not removed.
Remove it now.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The uart2 and its pinmux are already marked with u-boot,dm-spl but we
need to move the call to preloader_console_init() after spl_early_init()
to avoid a board hang as dm can't be used until after spl_early_init()
due to the uart driver not enabling the uart clock.
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me
tmp = 0x00ffff00
tmp = 0x00070700
tmp = 0x00000000
tmp = 0x00101000
and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.
So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.
This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The Avenger96 board comes in multiple regulator configurations.
- rev.100 or rev.200 have Buck3 preconfigured to 3V3 operation on
boot and contains extra Enpirion EP53A8LQI DCDC converter which
supplies the IO. Reduce Buck3 voltage to 2V9 to not waste power.
- rev.200L have Buck3 preconfigured to 1V8 operation and have no
Enpirion EP53A8LQI DCDC anymore, the IO is supplied from Buck3.
Configure the Buck3 voltage on this board per PMIC NVM settings and
update buck3 voltage limits in DT passed to OS before booting OS to
prevent potential hardware damage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This patch fixes the DP audio and video PLL configurations for the zynqmp-sm-k26-revA som.
The Linux DP driver expects the DP to be using the following PLL config:
- DP video PLL should use the VPLL (0x0)
- DP audio PLL should use the RPLL (0x3)
- DP system time clock PLL should use RPLL (0x3)
Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.
Register 0xFD1A007C configures the DP system time clock PLL.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fa7e9abc419c9d7648405d1c62367dbe701d09b8.1652709736.git.michal.simek@amd.com
This patch fixes the DP audio and video PLL configurations for the
zynqmp-zcu102-revA evaluation board.
The Linux DP driver expects the DP to be using the following PLL config:
- DP video PLL should use the VPLL (0x0)
- DP audio PLL should use the RPLL (0x3)
Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b2eb87758e0cd4844e1754da8c58fce58d9cf683.1651740949.git.michal.simek@amd.com
