Add board code for the R8A77980 V3HSK board.
Add CPLD sysreset driver to the R-Car V3H SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3H Condor, squash CPLD driver in]
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
The Lctech Pi F1C200s (also previously known under the Cherry Pi brand)
is a small development board with the Allwinner F1C200s SoC. This is the
same as the F1C100s, but with 64MB instead of 32MB co-packaged DRAM.
Add a defconfig for this board, enabling the most basic features. This
uses the new 64MB memory map, which avoids the very tight memory map we
use for the 32MB F1C100s board(s).
The devicetree file is already in the tree, courtesy of the previous
Linux repo sync.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is required for UART boot flow where u-boot.img needs to be
downloaded via YMODEM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Old Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c85b20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c85bfc
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf5bfc)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ EMPTY │
├─────────────────────────────────────┤ 0x41c81920
│ STACK │
│ SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000 │
├─────────────────────────────────────┤ 0x41c85920
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c859f0
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf59f0)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ 0x41cff9fc
│ NEW MCU SCRATCHPAD │
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Fixes: ab977c8b91 ("configs: j721s2_evm_r5: Enable support for building multiple dtbs into FIT")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[n-francis@ti.com: SRAM allocation addressing diagram]
Signed-off-by: Neha Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
As the ddr timing info will be saved at the last 16KB of
the OCRAM, spl stack & bss base should be updated to avoid
conflict.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a static u-boot config for i.MX93 low drive mode support. When
low drive mode is enabled, VDD_SOC is set to 0.75V. Bus clocks,
A55 core clock (900Mhz), DDR clock (1866MTS), and some peripherals
clocks (USDHC/FLEXSPI/PDM/DISP_PIX/CAM_PIX) must decrease to meet
max frequencies in low drive mode.
Also set standby voltage for buck1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 5 Model B.
Similar to RK3568 the BootRom in RK3588 can read all data and look for
idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1492992 bytes read in 129 ms (11 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x16c800
1300480 bytes written, 192512 bytes skipped in 11.103s, speed 137694 B/s
The BROM_BOOTSOURCE_ID value read back when booting from SPI flash does
not match the expected value of 3 (SPINOR) used by other SoCs. Instead a
value of 6 is read back, add a new enum value to handle this new
bootsource id.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
The phycore-rk3288 SPL binary is reaching the limits of 32KB very often.
Enable CONFIG_LTO to reduce the size of the SPL and make the board more
future proof for changes increasing the SPL size.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If u-boot is installed on the internal emmc, then this will
allow to boot without failure.
Signed-off-by: Wolfgang Zarre <lxdev12@zirdeon.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3588-rock-5b with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3588-evb with new defaults.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config options to include useful gpio and regulator cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Remove CONFIG_DEBUG_UART_ANNOUNCE=y to remove debug messages.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs, DM_RESET and DM_REGULATOR_FIXED is useful
across RK3588 platform. Select them from arch Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 3 Model A.
Unlike prior generation SoCs the BootRom in RK3568 can read all data and
look for idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1384448 bytes read in 119 ms (11.1 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x152000
1179648 bytes written, 204800 bytes skipped in 9.901s, speed 143185 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3568-rock-3a with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Remove the CONFIG_SPL_PMIC_RK8XX=y option, the pmic is not used in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3568-evb with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config options to include useful gpio, i2c, pmic and regulator cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add config options to enable support for the RK809 PMIC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3566-radxa-cm3-io with new defaults. Also add
missing supported mmc modes to sdhci node.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add drivers for PCIe , phy, and command.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_ROCKCHIP_SPI_IMAGE to build u-boot-rockchip-spi.bin.
Define CONFIG_SYS_SPI_U_BOOT_OFFS to write u-boot.itb at the expected
offset. Enable CONFIG_LTO to reduce size of SPL so that the mkimage
output fit before the 0x60000 offset in u-boot-rockchip-spi.bin.
=> sf probe
SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1442304 bytes read in 27 ms (50.9 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x160200
1421824 bytes written, 20480 bytes skipped in 9.501s, speed 155432 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on ROCK Pi 4.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
Add pinctrl driver in SPL. Do not remove pinctrl properties for SPL dtb.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB command, USB drivers, PHY and regulators, for USB host
operations.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Some of the Kria SOM and ZynqMP boards are using Analog Devices ethernet
phy. So, enable CONFIG_PHY_ADIN for all ZynqMP platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230420085645.21260-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move the TPL up a little to make room for the refcode binary blob. Also
increase the pre-relocation memory to make space for recent additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds a lot of code so that it cannot be built with the binary
blobs. It is not used on this board. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is useful when looking for tables in memory. Enable it for coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable support for NVMe storage devices. Update the driver to enable the
bus master bit, since coreboot does not do that automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Turn these options on to make it easier to debug things.
Also enable dhrystone so we can get some measure of performance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this so that PCI devices can be used correctly without needing
to do a manual scan.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is much more common on modern hardware, so default to using it.
This does not affect the normal UART, but does allow the debug UART to
work, since it uses serial_out_shift(), etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
- Rockchip NFC driver update and dev addr pointer api update;
- use standard dr_mode for usb driver;
- rock pi boards dts update;
- Add rk3566 Anbernic boards;
- Misc fixes for drivers;
rk3399-rock-pi-4a.dtb is enough for Radxa ROCK Pi 4A/B/A+/B+ and ROCK 4SE.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:
- Anbernic RG353M
- Anbernic RG353P
- Anbernic RG353V
- Anbernic RG353VS
- Anbernic RG503
The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.
Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.
The common specifications for each device are:
- Rockchip RK3566 SoC
- 2 external SDMMC slots
- 1 USB-C host port, 1 USB-C peripheral port
- 1 mini-HDMI output
- MIPI-DSI based display panel
- ADC controlled joysticks with a GPIO mux
- GPIO buttons
- A PWM controlled vibrator
- An ADC controlled button
All of the common features are defined in the devicetree synced from
upstream Linux.
TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some RK3399 boards, such as newer revisions of NanoPi R4S, do not
provide an EEPROM chip containing a globally unique MAC address.
Currently, this means that a randomly generated temporary MAC address
may be generated each time the device is rebooted, leading to ARP cache
issues and other confusing bugs.
Since RK3399 CPUs provide a built-in unique serial number, we can
reliably derive a locally MAC address from it by reading the
corresponding bits from the non-secure efuse block.
Enable configuration options that allow deriving a local MAC address
from the CPU serial number.
Test the IPv6 network discovery feature if indicated by boardenv file.
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Requires proper environment with DHCP6 server provisioned.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When CMPC885 board is used for MIAE device, SCC2 SCC3 and SMC2
are used for serial lines. Therefore only SCC4 is available for
handling the TDM line.
In order to use SCC4 in QMC mode without loosing SMC2, SMC2
must be relocated.
Activate SMC relocation and relocate SMC2 at offset 0x1fc0 which
is unused.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The recent series "Convert LS1088A and LX2160 to DM_SERIAL"
from Ioana Ciornei provided the necessary support to enable
DM_SERIAL on the Ten64 board (LS1088A).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Enable the CONFIG_TI_SECURE_DEVICE by default
Non-HS devices will continue to boot due to runtime device type detection.
TI's security enforcing SoCs will authenticate each binary it loads by
comparing it's signature with keys etched into the SoC during the boot
up process. The am62x family of SoCs by default will have some level of
security enforcement checking. To keep things as simple as possible,
enable the CONFIG_TI_SECURE_DEVICE options by default so all levels of
secure SoCs will work out of the box
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
In order to know the motherboard type earlier, perform I/O ports
initialisation and FPGA loading in board_early_init_f() instead
of board_early_init_r().
This is needed to be able to load mpc8xx CPM microcode base on
motherboard type and before starting to use the CPM.
Console is not available yet so remove the printfs.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers
Details: A device lockup can occur during the second read of any CPSW
subsystem register after any MAIN domain power on reset (POR). A MAIN
domain POR occurs using the hardware MCU_PORz signal, or via software
using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR.
After these resets, the processor and internal bus structures may get
into a state which is only recoverable with full device reset using
MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.
Workaround(s): To avoid the lockup, a warm reset should be issued after
a MAIN domain POR and before any access to the CPSW registers. The warm
reset realigns internal clocks and prevents the lockup from happening.
Workaround above errata by calling do_reset() in case of cold boot in
order to trigger warm reset. This needs enabling SYSRESET driver in R5
SPL to enable TI SCI reset driver.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Update the default BOOTCOMMAND to provide an automatic and easier way
to configure ethernet PHY before loading the firmware.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bootcmd/altbootcmd mechanism is not invoked for bootmenus.
Manually compare bootcount and bootlimit to implement fallback on all
codepaths.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Defaults have changed, we do not want the bootmenu to contain EFI
options.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add lockdown U-Boot env support so that only certain U-Boot environment
variables are allowed to be modified.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
GPT Partition labels are used for determining the right
root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware
boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader.
One can overwrite the inactive hardware partition with new bootloader
and environment and afterwards switch the eMMC boot partition for an
atomic bootloader switch.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Run the altbootcmd script if any step of bootcmd fails.
This ensures that always a valid image can be run.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add an altbootcmd script, which is convenient way to integrate with
swupdate and perform a roll back of the previous working version in the
case of update failure.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add automatic boot counter that increases after every
reset. After a power-on reset, it will be initialized with 1,
and each reboot will increment the value by 1. By default it is
disabled if bootlimit isn't set.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Select CONFIG_CMD_SQUASHFS so that the SquashFS U-Boot commands
are available.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
The "Programming Environments Manual for 32-Bit Implementations of the
PowerPC™ Architecture" says "W and G bits are not defined for IBAT
registers. Attempting to write to these bits causes boundedly-undefined
results"
The "e300 Power Architecture™ Core Family Reference Manual" says the
same: "Neither the W or G bits of the IBAT registers should be set.
Attempting to write to these bits causes boundedly-undefined results."
Remove the possibility to set those bytes.
Fixes: 30915ab95d ("mpc83xx: Migrate BATS config to Kconfig")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Mario Six <mario.six@gdsys.cc>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.
That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.
The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.
Additionally, the following board intentionally omits the property
because VBUS is always enabled:
- Nintendo_NES_Classic_Edition_defconfig /
sun8i-r16-nintendo-nes-classic
The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
