The function davinci_emac_mii_mode_sel() is defined in
board/davinci/common/misc.c for any DA8xx CPU which has
CONFIG_DRIVER_TI_EMAC enabled. However, the prototype was only being
declared in <include/asm/arch/davinci_misc.h> for the DA850 EVM board.
This patch declares it for all DA8xx CPUs where CONFIG_DRIVER_TI_EMAC
is enabled.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
These functions are not required when CONFIG_CMD_NET
is not defined:
- setup_net_chip()
- reset_net_chip()
- board_eth_init()
This patch wraps them in #ifdef CONFIG_CMD_NET...#endif
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.
The patch uses generic gpio API instead of direct access
to corresponding registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.
The patch moves the reset actions to new function reset_net_chip().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().
Enclose definition of this array in #ifdef...#endif for
the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
There is a optimized version of memset in u-boot available so use it instead
of the hand written loop version.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf
This patch has been tested with MX25L4005 and MX25L8005
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: jtag-console: fix timer usage
Blackfin: switch to common display_options()
Blackfin: serial: move early debug strings into .rodata section
Blackfin: adi boards: also set stderr to nc with helper
Blackfin: update anomaly lists to latest public info
Blackfin: serial: convert to bfin_{read,write} helpers
Blackfin: split out async setup
Blackfin: adi boards: enable pretty flash progress output
Blackfin: drop unused dma.h header from start code
Blackfin: portmux: allow header to be included in assembly files
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
Blackfin: sync MMR read/write helpers with Linux
Blackfin: gpio: optimize free path a little
Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
Blackfin: uart: fix printf warning
Blackfin: add init.elf helper code
Blackfin: dont reset SWRST on newer bf526 parts
Blackfin: adi boards: enable multi serial support by default
Blackfin: uart: add multiple serial support
Blackfin: uart: move debug buffers into local bss
Fix:
tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards
qualifiers from pointer target type
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix compiler warning:
cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type
Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
Also remove bogus comment.
Signed-off-by: Zhong hongbo <bocui107@gmail.com>
Changed commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Fix the following:
ERROR: do not initialise statics to 0 or NULL
ERROR: do not use assignment in if condition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Run cfb_console.c through indent and manually fix some of he
deficiencies of the automatic line breaking.
Fix multiline comments, excessive line spacing and such.
No changes to code done.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Amend section 'Directory Hierarchy' for current MIPS directory.
Describe config options for MIPS.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Currently the cache operation mode is hard-coded to
CONF_CM_CACHABLE_NONCOHERENT. This is not appropiate for CPUs or SOCs
which operate at a different mode.
This patch makes the cache operation mode configurable via board config.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
This define is a board-specific config option and should be
renamed to follow the U-Boot naming convention. Additionally,
add an explaining comment for this option.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The INCA-IP SoC belongs to the Lantiq XWAY SoC product portfolio.
For the upcoming support of other Lantiq SoC devices this tool should
not solely depend on the INCA-IP board.
Rename the tool to xway-swap-bytes and add an config option
to enable compilation optionally.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/8xxx: Remove dependency on <usb.h>
powerpc/85xx: enable USB2 gadget mode for corenet ds board
powerpc/85xx: verify the device tree before booting Linux
MPC8xxx: drop redundant boot messages
powerpc/85xx: Fix build failure for P1023RDS
powerpc/p2041rdb: Enable SATA support
powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500
powerpc/85xx: Fix up clock_freq property in CAN node of dts
85xx: enable FDT support for STX SSA board
powerpc/85xx: provide 85xx flush_icache for cmd_cache
powerpc/p2041rdb: Enable backside L2 cache support
powerpc/85xx: Handle the lack of L2 cache on P2040/P2040E
powerpc/85xx: Add support for P2041[e] XAUI in SERDES
powerpc/85xx: Rename P2040 id & SERDES to P2041
powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
powerpc/85xx: Fix setting of EPAPR_MAGIC value
This is needed to get rid of build warnings like
main.c:311: warning: passing argument 2 of 'setenv' discards qualifiers from pointer target type
which result from commit 09c2e90 "unify version_string".
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andreas Biemann <andreas.devel@googlemail.com>
We used <usb.h> for USB_MAX_DEVICE. However this requires we actual
build in support for USB into u-boot (which should not be required for
device tree fixup).
At this time no FSL SoC that utilizies this code (83xx/85xx) has more
than 2 USB controllers. So we replace USB_MAX_DEVICE with a local
define FSL_MAX_NUM_USB_CTRLS.
If/when a device shows up with more than 2 controllers we can easily
bump this value or refactor into a proper define per SoC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce ft_verify_fdt(), a function that is called after the device tree
has been fixed up, that displays warning messages if there is a mismatch
between the physical addresses of some devices that U-Boot has configured
with what the device tree says the addresses are.
This is a particular problem when booting a 36-bit device tree from a
32-bit U-Boot (or vice versa), because the physical address of CCSR is
wrong in the device tree. When the operating system boots, no messages are
displayed, so the user generally has no idea what's wrong.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we added the fman fdt fixup we forgot to fixup the P1023RDS
platform. So we would get:
fdt.c: In function 'fdt_fixup_fman_firmware':
fdt.c:465:15: error: 'CONFIG_SYS_FMAN_FW_LENGTH' undeclared (first use in this function)
fdt.c:465:15: note: each undeclared identifier is reported only once for each function it appears in
Add the needed #defines in P1023RDS.h to fix this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
At some point we broke the detection of e500v1 class cores. Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix up the device tree property associated with the Flexcan clock
frequency. This property is used to calculate the bit timing parameters
for Flexcan.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We also have to shift TEXT_BASE to accomodate for the additional
code size.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This provides a function that will override the weak function
flush_icache to let 85xx boards to flush the icache
cc: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
The P2040/P2040E have no L2 cache. So we utilize the SVR to determine
if we are one of these devices and skip the L2 init code in cpu_init.c
and release. For the device tree we skip the updating of the L2 cache
properties but we still update the chain of caches so the CPC/L3 node
can be properly updated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We add XAUI_FM1 into the SERDES tables for P2041[e] devices. However
for the P2040[e] devices that dont support XAUI we handle this at
runtime via SVR checks. If we are on a P2040[e] device the SERDES
functions will behave as follows:
is_serdes_prtcl_valid() will always report invalid if prtcl passed in is
XAUI_FM1.
serdes_get_prtcl() will report NONE if the prtcl in the table is set to
XAUI_FM1.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041 is the superset part that covers both P2040 & P2041. The only
difference between the two devices is that P2041 supports 10g/XAUI and
has an L2 cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.
Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Had a typo in the ifdef for 85xx, should be CONFIG_MPC85xx for it to get
triggered. Was pull in the non-BookE magic number.
Reported-by: John Cortell
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 09c2e90c11 "unify version_string"
introduced a build breakage in cfb_console.c
---8<---
cfb_console.c:1497: warning: format '%s' expects type 'char *', but
argument 3 has type 'const char (*)[]'
--->8---
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
This reverts commit c310fc8404.
The Atmel custodian had apparently rejected this patch's approach in
another thread, so this patch reverts it for now.
Signed-off-by: Andy Fleming <afleming@freescale.com>
since commit
commit d2e8b911c0
Author: Mike Frysinger <vapier@gentoo.org>
Date: Wed Jun 29 11:58:04 2011 +0000
panic: add noreturn attribute
I see the following warnings:
vsprintf.c: In function 'panic':
vsprintf.c:730: warning: 'noreturn' function does return
for nearly all boards. This patch fixes this warning.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Mike Frysinger <vapier@gentoo.org>
This include is needed, if this memory test is used "outside"
from post code, for example booting with nand_spl, and using
this memory test before copying u-boot code to RAM and jumping
to it.
Signed-off-by: Heiko Schocher <hs@denx.de>
