The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.
This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h
For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Read the boot mode register to find the boot mode. Only use eMMC boot0
mode when the mode is eMMC boot (called BOOT_DEVICE_MMC1 currently due
to current conflating of boot mode and boot device), and not iff the
boot device is MMC port 0.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
For most devices the boot mode maps directly to the boot
device. For MMC this is not the case as we have two MMC
boot modes and two MMC boot devices (ports). Check the
boot port to determine which MMC device was our boot
device. Make this change for both primary and secondary
boot modes.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Push generic defines of gpio.h out of mach-davinci to drivers/gpio
now that non-davinci architectures are beginning to use this IP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix calimain build]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM2 board based on a
Meson GXM (S912) SoC with the Meson GXM configuration.
This initial submission supports UART, MMC/SDCard and Ethernet.
USB is partially supported.
All the code is from Neil Armstrong! I just rebased the code, do
some cleanup and tested on my board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
This adds Device Tree for the Khadas VIM2 board.
The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Currently the DRAM bus gate and reset is changed at the same time in
H6 DRAM initialization code, which disobeys the user manual's
programming guide.
Fix the sequence by follow the sequence suggested by the user manual
(ungate the bus clock after release the reset signal).
By some experiments it seems to fix the DRAM size detection failure that
rarely happens.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The CPLD is used to reset the ULCB and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The current mem_map definition for Meson SoCs has support for up
to 2GiB of RAM. According to S905, S905X, S912 and S805X datasheets
the DDR region is set from 0x00000000 to 0xBFFFFFFF, so mem_map's
definition should be changed accordingly.
It is also needed to be able to boot Khadas VIM2 board with S912
SoC.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Sync with 14e21cb8f811 ("arm64: dt: hikey: Add optee node"
from Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
This allows to boot all STM32F7 and STM32H7 boards independently
of the amount of embedded SDRAM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences. With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)
Signed-off-by: Adam Ford <aford173@gmail.com>
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone. This cleans up
this unnneeded stuff.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device tree entries are from linux-omap's for-next branch
destined to me put into 4.20 (or whatever the version is after 4.19)
Signed-off-by: Adam Ford <aford173@gmail.com>
make_fit_atf.py uses physical address of first segment as the
entry point to bl31. It is incorrect and causes following abort
when bl31_entry() is called:
U-Boot SPL board initTrying to boot from MMC1
"Synchronous Abort" handler, esr 0x02000000
elr: 0000000000000000 lr : 00000000ff8c7e8c
x 0: 00000000ff8e0000 x 1: 0000000000000000
x 2: 0000000000000000 x 3: 00000000ff8e0180
x 4: 0000000000000000 x 5: 0000000000000000
x 6: 0000000000000030 x 7: 00000000ff8e0188
x 8: 00000000000001e0 x 9: 0000000000000000
x10: 000000000007fcdc x11: 00000000002881b8
x12: 00000000000001a2 x13: 0000000000000198
x14: 000000000007fdcc x15: 00000000002881b8
x16: 00000000003c0724 x17: 00000000003c0718
x18: 000000000007fe80 x19: 00000000ff8e0000
x20: 0000000000200000 x21: 00000000ff8e0000
x22: 0000000000000000 x23: 000000000007fe30
x24: 00000000ff8d1c3c x25: 00000000ff8d5000
x26: 00000000deadbeef x27: 00000000000004a0
x28: 000000000000009c x29: 000000000007fd90
Fix it by using the entry point from the elf header.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We package U-Boot and OP-TEE into one itb file for SPL,
so that we can support OP-TEE in SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Patch fix warning:
/builddir/BUILD/u-boot-2018.05-rc2/"arch/arm/mach-rockchip/make_fit_atf.py" \
arch/arm/dts/rk3399-firefly.dtb > u-boot.its
./tools/mkimage -f u-boot.its -E u-boot.itb >/dev/null && cat
/dev/null
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@2 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@3 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node
/configurations/config@1 has a unit name, but no reg property
make[1]: Leaving directory
'/builddir/BUILD/u-boot-2018.05-rc2/builds/firefly-rk3399'
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Additional sgmii phymode is added in socfpga_phymode_setup() along with
a minor fix for maximum number of GMACs.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Enable PHY framework on Gen3, this is required for USB EHCI PHY support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark area 0x1_0000_0000 - 0x10_0000_0000 as DRAM on Gen3 as the
chip is capable of addressing that and U-Boot can make use of it.
This patch prevents exception when accessing those areas.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The I2C6 is used to communicate with the PMIC and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
[picked from the identical linux patch
https://patchwork.kernel.org/patch/10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.
While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the omap_mmc driver no longer supporting cd-inverted, this
patch removes all these references since they are not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
