Based on thread
https://lists.denx.de/pipermail/u-boot/2021-June/451828.html
especially
"Overall we have a deficiency in the UEFI implementation in that we
cannot deal with block devices added or removed after initialization."
there is a need to deal with removable media as usb/scsi/sata.
That's why bridge this gap in EFI implementation by resetting usb and
scsi resets to get all disks before efi_init_obj_list() is called.
In our standard boot flow, where we use distro boot, order is fixed as
"jtag mmc0 mmc1 qspi0 nand0 usb0 usb1 scsi0 pxe dhcp" with prioritizing
boot device added by commit 2882b39d56 ("arm64: zynqmp: Setup the first
boot_target at run time").
When device has ESP partition all devices should be detected because then
efi_disk_register() in efi_init_obj_list() is called only once.
The first such a device is sd/emmc(mmc0/mmc1) and then disks on usb/sata
are not handled at all.
The commit 6bb577dbb3 ("arm64: zynqmp: Disable
EFI_CAPSULE_ON_DISK_EARLY") also pointed out on this issue but detection of
removable media wasn't solved that's why do it now via preboot command.
I have tested cases without usb and scsi and there is no problem with
calling resets without devices itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable watchdog driver in default zynqmp configuration. The reason
is that not all distributions are handling watchdog properly and then
expires and system resets. If someone needs watchdog in their design please
enable it by hand.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable RTC command to be able to check available.
And also enable ZynqMP RTC driver to be possible to use by default.
Here is the list when both drivers are enabled:
ZynqMP> rtc list
RTC #0 - rtc_emul
RTC #1 - rtc@ffa60000
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The main reason for this to be implemented is capsule update.
Two memories are supported and tested which is MMC FAT based and QSPI
based.
For creating capsule these commands are used:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.itb --index 2 capsule2.bin
Then transfer to SD card where these commands run:
load mmc 0 10000000 capsule1.bin
efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin
efidebug capsule update -v 10000000
Depends on the boot device used are binaries loaded to qspi or mmc fat
partition.
Also multiboot register is handled to make sure that the same location(id)
is used as image which is upgraded.
Two locations are used by purpose for SPL flow. If only boot.bin is used
create only one capsule.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This variable is pointing to offset is qspi where u-boot image is placed.
In our case it is location of u-boot.itb file. Offset is the same as is
used by Xilinx Zynq SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Fixed broken ICH SPI driver in software sequencer mode
- Added "m25p,fast-read" to SPI flash node for x86 boards
- Drop ROM_NEEDS_BLOBS and BUILD_ROM for x86 ROM builds
- Define a default TSC timer frequency for all x86 boards
- x86 MTRR MSR programming codes bug fixes
- x86 "hob" command bug fixes
- Don't program MTRR for DRAM for FSP1
- Move INIT_PHASE_END_FIRMWARE to FSP2
- Use external graphics card by default on Intel Crown Bay
- tangier: Fix DMA controller IRQ polarity in CSRT
The board routes the Integrated Graphics Device (IGD) to an LVDS
panel, which is less popular than a PCIe based graphics card.
Disable the IGD so that it does not show up in the PCI configuration
space as a VGA display controller, so we can use an external PCIe
graphics card with whatever cable we have.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
binman complains when binary blobs are present:
Node '/binman/rom/intel-vga': Offset 0xfff90000 (4294508544) overlaps
with previous entry '/binman/rom/u-boot-dtb-with-ucode' ending at
0xfff9204c (4294516812)
Adjust VGA rom address to 0xfffa0000 so that u-boot.rom image can be
successfully built again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 71025f013c ("mtd: spi-nor-core: Rework hwcaps selection")
SPI flash on Intel Crown Bay board does not work anymore.
Disable CONFIG_SPI_FLASH_SMART_HWCAPS until a proper fix is made to
the spi-nor core.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_HEXDUMP is needed to display UEFI variables using 'printenv -e'.
Enabling CONFIG_SPL_HEXDUMP only makes sense for debugging purposes.
Hence CONFIG_SPL_HEXDUMP should not be enabled by default.
The following boards currently have CONFIG_SPL_HEXDUMP=y. This includes
boards that don't use SPL at all.
axm_defconfig
imx8mm-cl-iot-gate_defconfig
imx8mm_venice_defconfig
imxrt1020-evk_defconfig
imxrt1050-evk_defconfig
kontron_sl28_defconfig
kp_imx53_defconfig
lx2160ardb_tfa_stmm_defconfig
mt7622_rfb_defconfig
octeon_ebb7304_defconfig
octeon_nic23_defconfig
qemu_arm64_defconfig
qemu_arm_defconfig
qemu-riscv32_defconfig
qemu-riscv32_smode_defconfig
qemu-riscv64_defconfig
qemu-riscv64_smode_defconfig
qemu-x86_64_defconfig
qemu-x86_defconfig
sandbox64_defconfig
sandbox_defconfig
stm32mp15_basic_defconfig
stm32mp15_trusted_defconfig
synquacer_developerbox_defconfig
taurus_defconfig
xilinx_versal_virt_defconfig
The patch only keeps it enabled on
sandbox_spl_defconfig
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The gdsys a38x config file (controlcenterdc_defconfig) uses BootROM to
load U-Boot proper.
Since it is now possible to do this via U-Boot SPL framework, we do not
need to provide custom spl_board_init() which calls return_to_bootrom().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
These don't belong in the drivers Makefile so move them down into
the correct place.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup some missing dependencies this exposed]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add test cases for the setexpr format string operator.
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com>
[trini: Enable on sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable configs to support SMBIOS for all Khadas VIM boards
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The J721E R5 SPL will no longer support booting of the Main R5FSS Core0
after the R5 SPL re-architecture for System Firmware split. The MCU R5F
branch-only boot does not use the K3 R5F remoteproc driver, and relies
only on the filesystem (FS) support for now. The K3 R5F remoteproc driver
is therefore no longer needed in R5 SPL, so drop it from the J721E R5
defconfig.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-6-s-anna@ti.com
Enable config to support gpt command on AM642 evm/sk and enable config for
FDT library overlay support
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-7-a-govindraju@ti.com
Kconfig symbols for SYS_MMC_ENV_DEV and SYS_MMC_ENV_PART have been added by
commit 7d08077334. Therefore, move the
definitions of configs to corresponding board defconfig files and enable
configs to save env in eMMC.
Also enable config for FAT write in U-Boot.
Fixes: 33b7258947 ("board: ti: am64x: Add board support for am64x evm")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-5-a-govindraju@ti.com
CONFIG_SPL_TEXT_BASE was set to 0x70000000 in the commit,
"26f32c32b250 configs: am64x_evm_*_defconfig: Rearrange the components in
SRAM to satisfy the limitations for USB DFU boot mode". This change seems
to have been dropped during a merge commit.
Therefore, fix this by setting CONFIG_SPL_TEXT_BASE to 0x70000000.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726145840.18977-1-a-govindraju@ti.com
Add CONFIG_PREBOOT to provide an automatic and easier way
to configure ethernet PHY before loading the firmware.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-19-kishon@ti.com
Add config for torrent serdes and common clock framework.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-17-kishon@ti.com
Enable the mmio mux driver, the J721E-wiz PHy driver and the cadence sierra
phy driver. All of them are required for USB3 support
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-16-kishon@ti.com
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
It is useful to have a board with unit tests enabled, to check that this
does not break.
Let's choose snow, since it is not under active development and it is
glorious.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.
Switch over to use driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
reset and poweroff are called via hooks in psci driver which is going
around sysreset framework that's why enable sysreset drivers and do reset
and poweroff via this framework. Using this flow will allow us to call
SYSTEM_WARM_RESET based on psci 1.1 spec which can be calles with reset -w
command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At the moment pressing the volume down key does not actually launch
fastboot. This is because setting "bootdelay" to "-1" actually
disables autoboot and drops to the U-Boot console. It does not execute
the "bootcmd".
The correct value for "bootdelay" here would be "-2", which disables
the delay and key checking and would immediately execute the "bootcmd".
However, even better in this case is using "preboot" to trigger Fastboot.
The advantage is that running "fastboot continue" will actually continue
the autoboot process instead of ending up in the U-Boot shell.
Also make sure to unset "preboot" again immediately in case the user
saves the environment after triggering fastboot.
Cc: Ramon Fried <rfried.dev@gmail.com>
Fixes: aa043ee91a ("db410c: automatically launch fastboot")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Since we can not set OsIndications from Runtime Services
SetVariables at this moment, it is better to ignore the
OsIndications if there is any capsule file in the
correct place.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since the recent commit;
commit b891ff18f8 ("efi_loader: Force a single FMP instance per hardware store")
forces a single FMP instances for a storage, we can not
enable both RAW and FIT capsule image support at once.
Since RAW capsule image support is simpler than FIT,
enable RAW capsule image instead of FIT by default.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Enable UEFI secure boot on synquacer. Note that unless user
setup their keys, the secure boot will not work.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
