nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add more BCH setting mode and remove the unnecessary platform constrain
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To enable the Randomizer module, set GPMI_ECCCTRL[RANDOMIZER_ENABLE] to
1, then set GPMI_ECCCOUNT[RANDOMIZER_PAGE] to select randomizer page
number needed to be randomized.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When enabled randomizer during ECC reading, the controller reported it's
erased page. Checking zero count will cause data get modified to all
0xFF. Stop checking during randomizer to workaround this issue.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
enable the GPMI NAND driver for i.MX8, i.MX8 use similar controller as
i.MX8M
- register definition for i.mx8
- DMA structure must be 32bit address
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx8mm needs to BCH encode and set NAND page number needed to be
randomized
modify conditional compilation
Use CONFIG_IMX8M, so it apply to imx8mq/mm/mn
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the gpmi/apbh_dma/bch drivers and relevant registers for i.MX8M.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is a porting of
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/
commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38
"
i.MX6QP and i.MX7D BCH module integrated a new feature to detect the
bitflip number for erased NAND page. So for these two platform, set the
erase threshold to gf/2 and if bitflip detected, GPMI driver will
correct the data to all 0xFF.
Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q
with the one for i.MX6QP.
"
In this patch, i.MX6UL is added and threshold changed to use ecc_strength.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is porting from linux:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/
?h=imx_4.1.15_1.0.0_ga&id=3d42fcece496224fde59f9343763fb2dfc5b0768
"
We may meet the bitflips in reading an erased page(contains all 0xFF),
this may causes the UBIFS corrupt, please see the log from Elie:
-----------------------------------------------------------------
[ 3.831323] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.845026] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.858710] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.872408] UBI error: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read 16384 bytes
...
[ 4.011529] UBIFS error (pid 36): ubifs_recover_leb: corrupt empty space LEB 27:237568, corruption starts at 9815
[ 4.021897] UBIFS error (pid 36): ubifs_scanned_corruption: corruption at LEB 27:247383
[ 4.030000] UBIFS error (pid 36): ubifs_scanned_corruption: first 6569 bytes from LEB 27:247383
-----------------------------------------------------------------
This patch does a check for the uncorrectable failure in the following steps:
[0] set the threshold.
The threshold is set based on the truth:
"A single 0 bit will lead to gf_len(13 or 14) bits 0 after the BCH
do the ECC."
For the sake of safe, we will set the threshold with half the gf_len, and
do not make it bigger the ECC strength.
[1] count the bitflips of the current ECC chunk, assume it is N.
[2] if the (N <= threshold) is true, we continue to read out the page with
ECC disabled. and we count the bitflips again, assume it is N2.
(We read out the whole page, not just a chunk, this makes the check
more strictly, and make the code more simple.)
[3] if the (N2 <= threshold) is true again, we can regard this is a erased
page. This is because a real erased page is full of 0xFF(maybe also has
several bitflips), while a page contains the 0xFF data will definitely
has many bitflips in the ECC parity areas.
[4] if the [3] fails, we can regard this is a page filled with the '0xFF'
data.
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Provide an option in DT to use legacy bch geometry, which compatible
with the 3.10 kernel bch setting. To enable the feature, adding
"fsl,legacy-bch-geometry" under gpmi-nand node.
NOTICE: The feature must be enabled/disabled in both u-boot and kernel.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The code change updated the NAND driver BCH ECC layout algorithm to
support large oob size NAND chips(oob > 1024 bytes) and proposed a new
way to set ECC layout.
Current implementation requires each chunk size larger than oob size so
the bad block marker (BBM) can be guaranteed located in data chunk. The
ECC layout always using the unbalanced layout(Ecc for both meta and
Data0 chunk), but for the NAND chips with oob larger than 1k, the driver
cannot support because BCH doesn’t support GF 15 for 2K chunk.
The change keeps the data chunk no larger than 1k and adjust the ECC
strength or ECC layout to locate the BBM in data chunk. General idea for
large oob NAND chips is
1.Try all ECC strength from the minimum value required by NAND spec to
the maximum one that works, any ECC makes the BBM locate in data chunk
can be chosen.
2.If none of them works, using separate ECC for meta, which will add one
extra ecc with the same ECC strength as other data chunks. This extra
ECC can guarantee BBM located in data chunk, of course, we need to check
if oob can afford it.
Previous code has two methods for ECC layout setting, the
legacy_calc_ecc_layout and calc_ecc_layout_by_info, the difference
between these two methods is, legacy_calc_ecc_layout set the chunk size
larger chan oob size and then set the maximum ECC strength that oob can
afford. While the calc_ecc_layout_by_info set chunk size and ECC
strength according to NAND spec. It has been proved that the first
method cannot provide safe ECC strength for some modern NAND chips, so
in current code,
1. Driver read NAND parameters first and then chose the proper ECC
layout setting method.
2. If the oob is large or NAND required data chunk larger than oob size,
chose calc_ecc_for_large_oob, otherwise use calc_ecc_layout_by_info
3. legacy_calc_ecc_layout only used for some NAND chips does not contains
necessary information. So this is only a backup plan, it is NOT
recommended to use these NAND chips.
Signed-off-by: Han Xu <b45815@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
mxs_nand_init_dma is only referenced from mxs_nand.c. It's not
referenced in any headers or outside code, so this patch
defines it as static.
Signed-off-by: Adam Ford <aford173@gmail.com>
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Renamed from drivers/mtd/nand/mxs_nand.c (Browse further)
