DEBUG_UART_SKIP_INIT is used only by debug UART and thus should depend
on DEBUG_UART.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 2c77c0d652 ("xyz-modem: Change getc timeout loop waiting")
fixes the loop delay when using a hw watchdog, assuming that watchdog
kicking is taken care of by getc(). But the xyzmodem driver tries to
do a getc only after confirming that a character is available like below:
while (!tstc()) {
till timeout;
}
if (tstc())
*c = getc();
and getc() does a watchdog reset only if it fails to see a character.
In this case, getc() always sees a character and never does a
watchdog reset. So to make sure that watchdog doesn't get reset
while loading the file, do a watchdog reset just before starting the
image loading.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pylibfdt needs Python 2 to build.
Replace $(PYTHON) with $(PYTHON2) in pylibfdt Makefile
to ensure Python 2 is used to build it.
This fixes build on systems where Python 3 is the default version
of the "python" interpreter.
Reviewed-by: Simon Glass <sjg@chromium.org>
The uuid command is only really useful in U-Boot, but it's useless in
SPL. Worse yet, it pulls in various environment manipulation functions
as it call env_set(). Do not compile the command in in SPL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add support for gunzip-ing gzip-compressed uImages in the SPL Ymodem code.
Loading data over Ymodem can be gruelingly slow, gzip-ing the data can
reduce that aggravating slowness at least slightly (depends on the data,
u-boot.bin compresses to ~1/3 of it's original size on ARM64), hence add
optional support for decompressing gzip-compressed uImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
The platdata initialization structs are currently generated into .rwdata.
Make sure the are put into .rodata by generating them as const.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
test->time_ms[] is defined as unsigned. So use %u for printf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio is defined as unsigned int. So we should use %u when calling printf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes.
Remove CONFIG_OF_EMBED from all stm32 config files which are using
this flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Make sure the block cache is cleared for the MMC device after it was
reinitialized to avoid having any stale data in the cache, like e.g.
partition tables or such.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
In case the card is removed, force-init the MMC to start the internal
machinery which deregisters and invalidate the MMC device.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.
In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.
However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Some tests have ended up using double quotes where single quotes could be
used. Adjust this for consistency with the rest of U-Boot's Python code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: Tom Rini <trini@konsulko.com>
Updates i2c muxes drivers to support livetree.
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is needed to properly calculate i2c bus speed divisors.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Wojciech Tatarski <wtatarski@antmicro.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Xilinx AXI I2C controller driver based on the Linux i2c-xiic driver.
This driver is stripped of all the IRQ handling and uses pure polling,
yet tries to retain most of the structure of the Linux driver to make
backporting of fixes easy.
Note that the IP has a known limitation on 255 bytes read and write,
according to xilinx this is still being worked on [1].
[1] https://forums.xilinx.com/t5/Embedded-Processor-System-Design/AXI-IIC-V2-0-I2C-Master-Reading-multiple-bytes-from-I2C-slave/m-p/854419/highlight/true#M39387
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
We need to define the standalone load address to use standalone
application on qemu-riscv. Define it and set it equal to
CONFIG_SYS_LOAD_ADDR.
To not overwrite it, change the assigned of CONFIG_STANDALONE_LOAD_ADDR
in arch/riscv/config.mk to a conditional one.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add an implementation of EXPORT_FUNC() for RV64I systems to support them
in standalone applications.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Register x19 (s3) is a callee-saved register. It must not be used to
load and jump to exported functions without saving it beforehand.
Replace it with t0, a temporary and caller-saved register.
Change the code comment to reflect this and fix it to correctly list gp
as the register with the pointer to global data.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Standalone applications do not require a separate linker script and can
use the default linker script of the compiler instead. Remove the RISC-V
standalone linker script.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The flush_cache() function in lib/cache.c ignores its arguments and
flushes the complete data and instruction caches. Use the
invalidate/flush_*cache_range() functions instead to only flush the
requested memory region.
This patch does not change the current behavior of U-Boot, since the
implementation of the invalidate/flush_*cache_range() functions flush
the complete data and instruction caches. It is in preparation for CPUs
with the necessary functionality for flushing a selectable memory range.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The fence instruction is used to enforce device I/O and memory ordering
constraints in RISC-V. It can not be relied on to directly affect the
data cache on every CPU.
Andes' AX25 does not have a coherence agent. Its fence instruction
flushes the data cache and is used to keep data in the system coherent.
The implementation of flush_dcache_all in lib/cache.c is therefore
specific to the AX25. Move it into the AX25-specific cache.c in
cpu/ax25/.
This also adds a missing new line between flush_dcache_all and
flush_dcache_range in lib/cache.c.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Undefined exceptions are treated as reserved. This is not clearly
communicated to the user. Adjust the error message to clarify that a
reserved exception has occurred and add additional details.
Fixes: e8b522b ("riscv: treat undefined exception codes as reserved")
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With 8 bytes addressing even on 32 bit machines these checks
are no longer valid. Remove them.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
when running the date command on sandbox_defconfig an error occurs:
./u-boot -D u-boot.dtb
=> date
i2c_emul_find() No emulators for device 'rtc@43'
## Get date failed
Correct the references to the emulator devices in the sandbox device trees
using test.dts as a reference.
Fixes: 031a650e13 ("dm: sandbox: i2c: Use new emulator parent uclass")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dropped unnecessary #address/size-cells property in i2c_emul:
Signed-off-by: Simon Glass <sjg@chromium.org>
The getconfig() comment is out of date. Fix this and add comments for
recently added functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
We should not be adding new functions to common.h. Move these recently
added functions to serial.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
At present this stores the error number in an unsigned int so an error is
never detected. Use the existing signed variable instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
