Unconditionally clearing DTO when RXDR is set leads to spurious timeouts
in FIFO mode transfers if events occur in the following order:
mask = dwmci_readl(host, DWMCI_RINTSTS);
// Hardware asserts DWMCI_INTMSK_DTO here
dwmci_writel(host, DWMCI_RINTSTS, DWMCI_INTMSK_DTO);
if (mask & DWMCI_INTMSK_DTO) {
// Unreachable as DTO is cleared without being handled!
return 0;
}
Only clear interrupts that we have seen and are handling so that DTO is
not missed.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org> (Rock PI 4B)
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The SDMMC IOs can be in an IO domain, that has to be enabled.
This is done by enabling vqmmc in the driver.
This has no impact on configurations not using an IO domain, the check
can then be executed on all platforms managing regulator, and the vqmmc
regulator enabled on all platforms having it in their DT.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The UHS modes for SD, HS200 and HS400 modes for eMMC are not supported
by the stm32_sdmmc2 driver.
Make it clear by removing the corresponding caps after parsing the DT.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To support dual data rate with STM32 sdmmc2 driver, the dedicated bit
(DDR - BIT(18)) needs to be set in the CLKRC register. Clock bypass
(no divider) is not allowed in this case. This is required for the
eMMC DDR modes.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Socionext F_SDH30_E51 IP support. The features of this IP includes
CMD/DAT line delay and force card insertion mode for non-removable cards.
And the IP needs to add some quirks.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
This patch defines a quirk to disable the block count
for single block transactions.
This is similar to Linux kernel commit d3fc5d71ac4d
("mmc: sdhci: add a quirk for single block transactions").
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Get rid of discrepancy beween comment /* 250 ms */ and code
which shifts by 4 thus dividing by 16.
So change code to shift by 2 and make the timeout value 250 ms.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Array index for SCCR 22th DWORD should be 21.
Fixes: bebdc23750 ("mtd: spi-nor: Parse SFDP SCCR Map")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The flash's internal address mode is tracked by nor->add_mode_nbytes and
it is set to 3 in BFPT parse. SEMPER multi-die package parts (>1Gb) are
3- or 4-byte address mode by default, depending on model number. We need
to make sure that 4-byte address mode is used for multi-die package parts.
For single-die package parts (<=1Gb), registers can be accessed by 3-byte
address. Read, program, and erase use the 4B opcodes that always take
4-byte address regardless of flash's internal address mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Read/Write Any Register commands take 3- or 4- byte address depending on
flash's internal address mode. The nor->addr_width tracks number of
address bytes used in read/program/erase ops that can be 4
(with 4B opcodes) regardless of flash's internal address mode. The
nor->addr_mode_nbytes tracks flash's internal address mode so replace
nor->addr_width by that.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The nor->addr_width tracks number of address bytes used in
read/program/erase ops and eventually set to 4 for >16MB chips, regardless
of flash's internal address mode. For Infineon SEMPER flash's, we use
Read/Write Any Register commands for configuration and status check.
These commands take 3- or 4-byte address depending on flash's internal
address mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216D-01 mentions that "defaults to 3-Byte mode; enters 4-Byte mode on
command."
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add flash info table entries for s28hl512gt, s28hl01gt, and s28hs01gt.
These devices have the same functionality as s28hs512t.
In spi-nor-core, use device ID byte to detect S28 family instead of
device name.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Change configuration macro name to support all other devices in SEMPER S28
family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Change prefix to support all other devices in SEMPER S28 family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- NC-SI handling support and enable on evb-ast2[56]00, gpio driver for
ADP5585, improve qfw support, print more sysresets info, gw_ventana
and gcc-12 bugfix, improve BCB support, fix a few typos and remove an
unused keymile CONFIG symbol.
In some cases, the param variable is wrong, and in other cases we have
undocumented arguments.
Fix the docs.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For other sandbox tests the printed test name corresponds to the
configuration except for this one.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some blk operations, it's possible that a different hw partition
gets selected via blk_dselect_hwpart().
In that case, only the region of the device covered by that partition
is accessible.
This breaks "bcb load" which attempts to read the gpt and assumes it's
on the user(0) hw partition:
=> bcb load 2 misc
GUID Partition Table Header signature is wrong: 0xDE7B17AD07D9E5D6 != 0x5452415020494645
find_valid_gpt: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
find_valid_gpt: *** ERROR: Invalid Backup GPT ***
Error: mmc 2:misc read failed (-2)
Add a fail-safe in __bcb_load() to ensure we will always read from the
user(0) hwpartition.
This fixes the following fastboot sequence:
$ fastboot erase mmc2boot1 # switch to hwpart1
$ fastboot reboot bootloader # switch to hwpart0, then reads GPT
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Building with GCC 12.2 results in an error
board/gateworks/gw_ventana/gw_ventana.c:636:68: error: the comparison
will always evaluate as 'true' for the address of 'pwm_padmux' will
never be NULL [-Werror=address]
636 | } else if (hwconfig_subarg_cmp(arg, "mode", "pwm") &&
| ^~
Remove the superfluous check.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Boards can have multiple sysresets, iterate all when printing sysreset
info.
Fixes: 23471aed5c ("board_f: Add reset status printing")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At the moment the QEMU boot sequence tries various (storage) devices
when trying to find a payload to boot.
To simplify starting a specific kernel and initrd, there is also the qfw
command, which can use the files specified on the QEMU command line, via
the -kernel and -initrd options.
Add this command to the list of boot options to try. Since users
specifying those options on the command line probably explicitly want
to run them, let's place the new command first. Without those options,
the qfw command will just gracefully fail, and we continue with the
existing order.
This allows auto-booting of specific kernels in QEMU, for instance in CI
systems.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When we try to load a kernel via the QEMU firmware device, we currently
"return -1;" if no kernel was specified on the QEMU command line. This
leads to the usage output, which is confusing (since nothing on the
command line was really wrong), but also somewhat hides the actual error
message.
Return CMD_RET_FAILURE (1), as it's a proper error, and make the message
more clear that this is not only a "warning".
This helps to call this command in boot scripts, and to gracefully
continue if this doesn't work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment the QEMU firmware command just prints the size of the
loaded binaries on the console.
To go with all the other load methods, and many boot scripts'
expectations, also store the size of the file loaded last in the
environment variable "filesize".
We first put the kernel size in there, but overwrite this with the
initrd size, should we have one, because this is probably the more
prominent user of $filesize (in the booti or bootz command).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add gpio driver for ADP5585 I/O Expander Controller. The ADP5585 is a 10
input/output port expander and can be used to increase the number of
I/Os available to a processor.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Aspeed BMCs are commonly used with NC-SI. A system indicates the driver
should configure the link over NC-SI using the device tree.
Add it to the defconfig so we get compile coverage of the driver, even
if the EVBs do not normally use it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Update the ftgmac100 driver to support NC-SI instead of an mdio phy
where available. This is a common setup for Aspeed AST2x00 platforms.
NC-SI mode is determined from the device-tree if either phy-mode sets it
or the use-ncsi property exists. If set then normal mdio setup is
skipped in favour of the NC-SI phy.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds an "ncsi" command to manually start NC-SI configuration.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Add the handling of NC-SI ethernet frames, and add a check at the start
of net_loop() to configure NC-SI before starting other network commands.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
- Enforce CONFIG_DM being enabled (which has been the case for all
boards for a bit now) and remove non-DM_KEYBOARD options as they're also
unused for some time now.
There are no platforms that have not migrated to using DM_KEYBOARD,
remove the legacy option.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no longer any platforms which do not enable DM, move this to a
def_bool y and remove the check in the Makefile.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmNSPhMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDrHCACddHL6pElPVUvNWomJ
h7RNejIaFrm+V2tVoDqnUBEzxKod7g1cvBiZM+2o5fcLNIrWfH0gV+7a48Uybzt2
r7VZ9u5Rnl1Fhhjvr8eL3uF/39V249eMPrzR8xC677sCJJkcczoOw8n4y534FaJZ
1NePmMKhlo7YVEZKzwdg1sM6sUppXniSEXUllWumVaUgSHcZhFK579nCbYpt25bW
sJ1V3fY2pJnaFHv9H599zSK79Izf5fR4fr3egKZknw8oqNLKNrjkWxxlPXJfjEYr
ncFJ31dOZXJU09rRoE60nIc0QdRE8dvELjYhPKUS/wmFDg7IotwNj5GcX2RIlRPJ
mS22
=D3FL
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.01 cycle:
This small fixes set includes an indentation fix for sam9x60 DT and one
name for one pin for sama7g5.
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Fix the MMC env device for boards with eMMC by adding a
board_mmc_get_env_dev override to return the boot device as the
MMC env device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
With sf update fixed to support unaligned start offset, use plain
sf update to update the bootloader in SPI NOR. This also helps
avoid the case where not enough SPI NOR has been erased and the
bootloader has been written to unerased area, and thus corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The btrfs filesystem provides advanced functionality like copy-on-write
and snapshots, as well as metadata and data duplication and checksumming.
Enable btrfs in U-Boot to permit even the primary partition to be btrfs
and let system boot from it.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
issue:
CAAM fails with key error when perform Modular Exponentiation
using PKHA Block in CAAM
Fix:
add flush and invalidate dcache for keys, signature
and output decrypted data processed by CAAM.
Fixes: 34276478f7 (DM: crypto/fsl - Add Freescale rsa DM driver)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Update the distro config env memory layout for the Apalis iMX6,
Colibri iMX6, Colibri iMX6ULL and Colibri iMX7:
- loadaddr=0x84200000 (resp. 0x14200000 on them i.MX 6) allows for 64MB
area for uncompressing (ie FIT images)
- fdt_addr_r = loadaddr + 64MB : allows for 64MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- pxefile_addr_r = scriptaddr + 512KB : allows for 512KB script
- ramdisk_addr_r = pxefile_addr_r + 512KB : allows for 1MB extlinux.conf
Memory layout analogous to 64-bit one from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but left pxefile_addr_r
updated according to doc/develop/distro.rst.
This fixes a potential issue caused by the compressed kernel being
relocated on top of the ramdisk causing its corruption.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
After commit 395110284b ("nitrogen6x: Populate FDTFILE at build-time
for all platforms") iMX.6Q Sabrelite fails to boot due to a bad fdtfile
string:
Retrieving file: /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb
** File not found /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb **
CONFIG_DEFAULT_DEVICE_TREE option is string typed, so __stringify() is
adding extra quotes. Remove this.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the
QSPI clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the
ecspi clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock
inside the non-SPL block to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
PWM is not used inside SPL, so do not define the PWM clocks inside
SPL to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Move init_clk_usdhc to non-clk driver case, since assigned-clocks properties
will initialize the clocks by clk driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
