The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds pfe stop command before boot linux kernel
to fix a problem that ethernet won't be workable
after enter linux. Because there is a h/w limitation
in LS1012A PFE, to re-initialize PFE it has to be
safe shutdown, these steps are done through PFE stop.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This configuration enables picking the environment from flash before
DDR init.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Moved CONFIG_FSL_ESDHC from header files to defconfig files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
esbc_validate command will not be executed if “load” command for its
header fails and will further execute the source command for bootscript,
without its validation and boot process continues.
To halt the boot process in case secure boot header is not loaded
successfully, esbc_validate command is invoked separately after “load”
command. The secure boot validation of the bootscript header will fail
(if header is not loaded) and halts the boot process, which prevent source
command from execution.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
TFABOOT support includes:
- ls1012a2g5rdb/ls1012afrdm/ls1012afrwy_tfa_defconfig to be
loaded by trusted firmware
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: remove unnecessary braces]
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
