The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).
Signed-off-by: Stefan Roese <sr@denx.de>
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
Signed-off-by: Stefan Roese <sr@denx.de>
Add ICMP_ECHO_REQUEST packet support by responding with a ICMP_ECHO_REPLY.
This permits the ping command to test the phy interface when the phy
is put in loopback mode (typically by setting register 0 bit 14).
It also allows the port to respond to an external ping when u-boot is
processing some other net command (such as tftp). This is useful when
tftp appears to hang.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem that occurs when 2 DIMM's are
used. This problem was first spotted and fixed by Gerald Jackson
<gerald.jackson@reaonixsecurity.com> but this patch fixes the
problem in a little more clever way.
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
As this feature is new to the "old" 44x SPD DDR driver, it
has to be enabled via the CONFIG_PROG_SDRAM_TLB define.
Signed-off-by: Stefan Roese <sr@denx.de>
As provided by the AMCC applications team, this patch optimizes the
DDR2 setup for 166MHz bus speed. The values provided are also save
to use on a "normal" 133MHz PLB bus system. Only the refresh counter
setup has to be adjusted as done in this patch.
For this the NAND booting version had to include the "speed.c" file
from the cpu/ppc4xx directory. With this addition the NAND SPL image
will just fit into the 4kbytes of program space. gcc version 4.x as
provided with ELDK 4.x is needed to generate this optimized code.
Signed-off-by: Stefan Roese <sr@denx.de>
The config value for:
* CFG_ACR_PIPE_DEP
* CFG_ACR_RPTCNT
* CFG_SPCR_TSEC1EP
* CFG_SPCR_TSEC2EP
* CFG_SCCR_TSEC1CM
* CFG_SCCR_TSEC2CM
Were not being used when setting the appropriate register
Added:
* CFG_SCCR_USBMPHCM
* CFG_SCCR_USBDRCM
* CFG_SCCR_PCICM
* CFG_SCCR_ENCCM
To allow full config of the SCCR.
Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349
that were just bogus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, this patch
updates ftp_cpu_setup() to write the MAC address to mac-address if it exists.
This function already updates local-mac-address.
Signed-off-by: Timur Tabi <timur@freescale.com>
The code supply fixed and SPD initialization for MPC83xx DDR2 Controller.
it pass DDR/DDR2 compliance tests.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8360E rev2.0 have new spridr,and PVR value,
The MDS board for MPC8360E rev2.0 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8349E rev3.1 have new spridr,and PVR value,
The MDS board for MPC8349E rev3.1 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo<X.Xie@freescale.com>
Fix empty i2c reads/writes, i2c_write(0x50, 0x00, 0, NULL, 0)
which is used to se if an slave will ACK after receiving its address.
Correct i2c probing to use this method as the old method could upset
a slave as it wrote a data byte to it.
Add a small delay in i2c_init() to let the controller
shutdown any ongoing I2C activity.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX. Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.
Signed-off-by: Timur Tabi <timur@freescale.com>
There is no SDRAM on any of the 8349 ITX variants, so function sdram_init()
never does anything. This patch deletes it.
Signed-off-by: Timur Tabi <timur@freescale.com>
The patch solves the alignment problem of the local bus access windows to
render accessible the memory bank and PHY registers of UPC 1 (starting at
0xf801 0000). What we actually did was to adjust the sizes of the bus
access windows so that the base address alignment requirement would be met.
Signed-off-by: Chereji Marian <marian.chereji@freescale.com>
Signed-off-by: Gridish Shlomi <gridish@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
The problem is not gcc4 but the code itself. The BD_STATUS() macro can't
be used for busy-waiting since it strips the 'volatile' property from
the bd variable. gcc3 was working by pure luck.
This is a follow on patch to "Fix the UEC driver bug of QE"
The code that is ifdef'd with CONFIG_MPC8349 is actually applicable to all
MPC834X class processors. Change the protections from CONFIG_MPC8349 to
CONFIG_MPC834X so they are more generic.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
Put the version (and magic) after the HRCW. This puts it in a fixed
location in flash, not at the start of flash but as close as we can get.
Signed-off-by: Jerry Van Baren <vanbaren@cideas.com>
