Commit graph

2378 commits

Author SHA1 Message Date
Russ Dill
335b4e53c9 ARM: am33xx: Always inhibit init/refresh during DDR phy init
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:

69b918 "am33xx,ddr3: fix ddr3 sdram configuration"
fc46ba "arm: am437x: Enable hardware leveling for EMIF"

The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25 12:00:06 -04:00
Russ Dill
3325b06556 ARM: am33xx: Fix DDR init delay placement
The delay needs to be before the write to ref_ctrl register
which initiates refreshes. An improper initialization sequence
generates an L3 noc error.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25 12:00:06 -04:00
Andreas Dannenberg
38d592fc33 arm: omap5: fix build dependency for secure devices
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:26 -04:00
Andreas Dannenberg
8b76d23ebd arm: am4x: fix build dependency for secure devices
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:26 -04:00
Ladislav Michl
9a9d394639 armv7: simplify identify_nand_chip
Use newly introduced function

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22 14:46:11 -04:00
Ladislav Michl
22d6ac490e armv7: armv7: introduce set_gpmc_cs0
Allow boards to runtime detect flash type.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22 14:46:11 -04:00
Ladislav Michl
0568dd0663 armv7: make gpmc_cfg const
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[trini: Adapt am33xx, duovero, omap_zoom1]
Signed-off-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:00 -04:00
Ladislav Michl
b1509e3a4a armv7: add reset timeout to identify_nand_chip
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22 09:53:00 -04:00
Fabio Estevam
8f2e2f15ff mx6: clock: Fix the logic for reading axi_alt_sel
According to the IMX6DQRM Reference Manual, the description
of bit 7 (axi_alt_sel) of the CCM_CBCDR register is:

"AXI alternative clock select
0 pll2 396MHz PFD will be selected as alternative clock for AXI root clock
1 pll3 540MHz PFD will be selected as alternative clock for AXI root clock "

The current logic is inverted, so fix it to match the reference manual.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-20 18:26:37 +02:00
Tom Rini
66669fcf80 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/cpu/armv8/Makefile
	arch/arm/lib/bootm-fdt.c
2016-07-19 16:38:57 -04:00
Hou Zhiqiang
45684ae37b ARMv8/PSCI: Fixup the device tree for PSCI
Set the enable-method in the cpu node to PSCI, and create device
node for PSCI, when PSCI was enabled.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-19 11:34:07 -07:00
Stefan Agner
be1a17ff68 mx7_common: use Kconfig for ARMv7 non-secure mode
Use existing Kconfig symbols to let the user configure whether to
build a U-Boot with non-secure mode support or not. This also allows
to enable virtualization extension easily.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2016-07-19 19:52:15 +02:00
Stefan Agner
ec7fde3ebf mx7: set soc environment according to exact SoC type
This can be useful if the same U-Boot binary is used for boards
available with a i.MX 7Solo and i.MX 7Dual.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-19 19:52:14 +02:00
Robert P. J. Day
62a3b7dd08 Various, unrelated tree-wide typo fixes.
Fix a number of typos, including:

     * "compatble" -> "compatible"
     * "eanbeld" -> "enabled"
     * "envrionment" -> "environment"
     * "FTD" -> "FDT" (for "flattened device tree")
     * "ommitted" -> "omitted"
     * "overriden" -> "overridden"
     * "partiton" -> "partition"
     * "propogate" -> "propagate"
     * "resourse" -> "resource"
     * "rest in piece" -> "rest in peace"
     * "suport" -> "support"
     * "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-07-16 09:43:12 -04:00
Tom Rini
1f9ef0dca0 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-07-15 10:44:01 -04:00
Chen-Yu Tsai
b7073965a3 ARM: PSCI: Make psci_get_cpu_stack_top local to armv7/psci.S
Now that we have a secure data section for storing variables, there
should be no need for platform code to get the stack address.

Make psci_get_cpu_stack_top a local function, as it should only be
used in armv7/psci.S and only by psci_stack_setup.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:58 +02:00
Chen-Yu Tsai
6e6622de16 ARM: PSCI: Switch to per-CPU target PC storage in secure data section
Now that we have a secure data section and space to store per-CPU target
PC address, switch to it instead of storing the target PC on the stack.

Also save clobbered r4-r7 registers on the stack and restore them on
return in psci_cpu_on for Tegra, i.MX7, and LS102xA platforms.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:58 +02:00
Chen-Yu Tsai
45c334e6b2 ARM: PSCI: Add helper functions to access per-CPU target PC storage
Now that we have a data section, add helper functions to save and fetch
per-CPU target PC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:58 +02:00
Chen-Yu Tsai
afc1f65f50 ARM: Move __secure definition to common asm/secure.h
sunxi and i.mx7 both define the __secure modifier to put functions in
the secure section. Move this to a common place.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:57 +02:00
Chen-Yu Tsai
28f9035732 ARM: PSCI: Remove unused psci_text_end symbol
psci_text_end was used to calculate the PSCI stack address following the
secure monitor text. Now that we have an explicit secure stack section,
this is no longer used.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:57 +02:00
Chen-Yu Tsai
8c0ef7fad6 ARM: PSCI: Allocate PSCI stack in secure stack section
Now that we have a secure stack section that guarantees usable memory,
allocate the PSCI stacks in that section.

Also add a diagram detailing how the stacks are placed in memory.

Reserved space for the target PC remains unchanged. This should be
moved to global variables within a secure data section in the future.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:57 +02:00
Chen-Yu Tsai
94a389b257 sunxi: Move remaining PSCI assembly code to C
This patch finishes the rewrite of sunxi specific PSCI parts into C
code.

The assembly-only stack setup code has been factored out into a common
function for ARMv7. The GIC setup code can be renamed as psci_arch_init.
And we can use an empty stub function for psci_text_end.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:56 +02:00
Chen-Yu Tsai
b52813239c ARM: PSCI: Split out common stack setup code from psci_arch_init
Every platform has the same stack setup code in assembly as part of
psci_arch_init.

Move this out into a common separate function, psci_stack_setup, for
all platforms. This will allow us to move the remaining parts of
psci_arch_init into C code, or drop it entirely.

Also provide a stub no-op psci_arch_init for platforms that don't need
their own specific setup code.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:56 +02:00
Simon Glass
6b424611a8 arm: Don't invalidate unaligned cache regions
At present armv7 will unhappily invalidate a cache region and print an
error message. Make it skip the operation instead, as it does with other
cache operations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-07-14 18:33:10 -04:00
Simon Glass
397b5697ad arm: Move check_cache_range() into a common place
This code is common, so move it into a common file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-07-14 18:33:09 -04:00
Lokesh Vutla
663f6fcaf0 ARM: OMAP5+: Enable errata i727
Errata i727 is applicable on all OMAP5 and DRA7 variants but enabled only
on OMAP5 ES1.0. So, enable it on all platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:45 -04:00
Madan Srinivas
e29878fc47 arm: am4x: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:23 -04:00
Andreas Dannenberg
17c2987336 arm: omap5: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:22 -04:00
Andreas Dannenberg
bf9ec864f4 arm: omap-common: Update to generate secure U-Boot FIT blob
Adds commands so that when a secure device is in use and the SPL is
built to load a FIT image (with combined U-Boot binary and various
DTBs), these components that get fed into the FIT are all processed to
be signed/encrypted/etc. as per the operations performed by the
secure-binary-image.sh script of the TI SECDEV package. Furthermore,
perform minor comments cleanup to make better use of the available
space.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-14 18:22:20 -04:00
Andreas Dannenberg
1bb0a21b46 arm: omap-common: secure ROM signature verify API
Adds an API that verifies a signature attached to an image (binary
blob). This API is basically a entry to a secure ROM service provided by
the device and accessed via an SMC call, using a particular calling
convention.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:19 -04:00
Andreas Dannenberg
d86f7afda4 arm: omap-common: add secure rom call API for secure devices
Adds a generic C-callable API for making secure ROM calls on OMAP and
OMAP-compatible devices. This API provides the important function of
flushing the ROM call arguments to memory from the cache, so that the
secure world will have a coherent view of those arguments. Then is
simply calls the omap_smc_sec routine.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:19 -04:00
Daniel Allred
51d0638650 arm: omap-common: add secure smc entry
Add an interface for calling secure ROM APIs across a range of OMAP and
OMAP compatible high-security (HS) device variants. While at it, also
perform minor cleanup/alignment without any change in functionality.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:18 -04:00
Daniel Allred
ec6f61003b arm: cache: add missing dummy functions for when dcache disabled
Adds missing flush_dcache_range and invalidate_dcache_range dummy
(empty) placeholder functions to the #else portion of the #ifndef
CONFIG_SYS_DCACHE_OFF, where full implementations of these functions
are defined.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:17 -04:00
Peng Fan
1f17562796 imx6: clock: typo fix
Typo fix, "PPL2 -> PLL2"

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-07-12 17:58:50 +02:00
Stefano Babic
876a25d289 mx6: Add Phytec PCM058 i.MX6 Quad
Add Phytec-i.MX6 SOM with NAND

  Support:
   - 1GB RAM
   - Ethernet
   - SPI-NOR Flash
   - NAND (1024 MB)
   - external SD
   - UART

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12 17:58:48 +02:00
Stefano Babic
8be4f40ecf mx6: add support for el6x board
Custom Board based on MX6 Dual, 1GB RAM and eMMC.

There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-07-12 17:58:48 +02:00
Marek Vasut
2b1cdafa9f common: Pass the boot device into spl_boot_mode()
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.

The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Steve Rae
8ada4e0ee6 arm: bcm235xx: update clock framework
The handling of the "usage counter" is incorrect, and the clock should
only be disabled when transitioning from 1 to 0.

Reported-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-24 17:24:38 -04:00
Chris Brand
77a1a677a6 arm: bcm235xx: fix kps ccu
The Kona Peripheral Slave CCU has 4 policy mask registers, not 8.

Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-24 17:24:37 -04:00
Masahiro Yamada
ec048369e2 ARM: armv7: refactor Makefile slightly
Use Kbuild standard style where possible.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-24 17:24:34 -04:00
Daniel Gorsulowski
85a2f772c2 omap3: bugfix in timer on rollover
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
2016-06-24 17:21:55 -04:00
Chen-Yu Tsai
4257f5f8f6 sunxi: Add PSCI implementation in C
To make the PSCI backend more maintainable and easier to port to newer
SoCs, rewrite the current PSCI implementation in C.

Some inline assembly bits are required to access coprocessor registers.
PSCI stack setup is the only part left completely in assembly. In theory
this part could be split out of psci_arch_init into a separate common
function, and psci_arch_init could be completely in C.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:44:00 +02:00
Chen-Yu Tsai
3424c3f299 sunxi: Add base address for GIC
Instead of hardcoding the GIC addresses in the PSCI implementation,
provide a base address in the cpu header.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:44:00 +02:00
Chen-Yu Tsai
0f3b894426 sunxi: Make CPUCFG_BASE macro names the same across families
Use SUNXI_CPUCFG_BASE across all families. This makes writing common
PSCI code easier.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:44:00 +02:00
Chen-Yu Tsai
778dc5f43e ARM: PSCI: save and restore clobbered registers in v7_flush_dcache_all
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:43:59 +02:00
Chen-Yu Tsai
dae08d2281 ARM: PSCI: use only r0 and r3 in psci_get_cpu_stack_top()
For psci_get_cpu_stack_top() to be usable in C code, it must adhere to
the ARM calling conventions. Since it could be called when the stack
is still unavailable, and the entry code to linux also expects r1 and
r2 to remain unchanged, stick to r0 and r3.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:43:59 +02:00
Lokesh Vutla
165bd7a1cc board: am57xx: Rename TARGET_BEAGLE_X15 as TARGET_AM57XX_EVM
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.

Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Steve Rae
43486e4cd0 board: arm:: Add support for Broadcom BCM23550
Add support for the Broadcom BCM23550 board.

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-13 08:56:02 -04:00
Tom Rini
fd9102dafe Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-06-13 08:50:58 -04:00
Simon Glass
b5bd09820c arm: Allow skipping of low-level init with I-cache on
At present CONFIG_SKIP_LOWLEVEL_INIT prevents U-Boot from calling
lowlevel_init(). This means that the instruction cache is not enabled and
the board runs very slowly.

What is really needed in many cases is to skip the call to lowlevel_init()
but still perform CP15 init. Add an option to handle this.

Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Keerthy
1428d83270 arm: dra7xx: Assign omap_vcores based on board type
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-12 13:14:57 -04:00
Tom Rini
3fc304b8d7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-06-12 12:51:34 -04:00
Heiko Schocher
3a504d9639 mtd: nand: omap: allow to switch to BCH16
support in omap_nand_switch_ecc() also an eccstrength
from 16.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:12 -04:00
Heiko Schocher
a4475af5b4 armv7: omap-common: make SPL board_mmc_init() weak
make this function weak, so board code can setup in SPL
MMC init with board special values.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:09 -04:00
Heiko Schocher
694607b563 arm, am335x: Enable Spread Spectrum for the MPU
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:07 -04:00
Tom Rini
d77fa2ff76 Merge http://git.denx.de/u-boot-samsung
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/peach-pi_defconfig
	configs/peach-pit_defconfig
2016-06-06 13:39:43 -04:00
Ladislav Michl
e22455f0a6 armv7: fix order of OMAP die ID printing
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2016-06-06 13:39:17 -04:00
Keerthy
61462cd772 arm: omap: Introduce vcores_init function
The pmic registers for variants of am57xx boards are different
hence we need to assign them carefully based on the board type.
Add a function to assign omap_vcores after the board detection.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-02 21:42:18 -04:00
Anna, Suman
e42523f544 ARM: DRA7: Consolidate voltage macros across different SoCs
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.

This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:17 -04:00
Anna, Suman
27c9596f68 ARM: DRA7: Define common macros for efuse register offsets
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:16 -04:00
Roger Quadros
3599774eec dra7xx: Enable USB_PHY3 32KHz clock
DRA7xx has a 32KHz PHY clock for USB_PHY3 that must be enabled
for USB1 instance in Super-Speed.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-06-02 21:42:15 -04:00
Roger Quadros
383f4a0ec7 ARM: OMAP5+: Provide enable/disable_usb_clocks() for CONFIG_USB_XHCI_OMAP
CONFIG_USB_XHCI_OMAP is enabled for host mode independent of CONFIG_USB_DWC3
which is meant for gadget mode only. We need enable/disbale_usb_clocks() for
host mode as well so provide for it.

Fixes: 09cc14f4bc ("ARM: AM43xx: Add functions to enable and disable USB clocks"
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-06-02 21:42:14 -04:00
Peng Fan
9f8fa184fc imx: mx7: implement reset_misc
We need to power down lcdif to make 'reset' can pass stress test.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-31 17:42:31 +02:00
Lokesh Vutla
9b77b19178 ARM: OMAP4+: Fix DPLL programming sequence
All the output clock parameters of a DPLL needs to be programmed before
locking the DPLL. But it is being configured after locking the DPLL which
could potentially bypass DPLL. So fixing this sequence.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
2016-05-27 15:47:57 -04:00
Lokesh Vutla
3164f3c689 ARM: AM33xx: Add support for Clock Synthesizer
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.

Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:52 -04:00
Daniel Allred
1aad38f6e6 ARM: omap5: add hooks for cpu/SoC fdt fixups
Adds an fdt.c file in that defines the ft_cpu_setup() function,
which should be called from a board-specific ft_board_setup()).
This ft_cpu_setup() will currently do nothing for non-secure (GP)
devices	but contains pertinent updates for booting on secure (HS)
devices.

Update the omap5 Makefile to include the fdt.c in the build.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:37 -04:00
Daniel Allred
47c331ede1 ARM: omap-common: Add device type to CPU string
Update the CPU string output so that the device
type is now included as part of the CPU string that
is printed as the SPL or u-boot comes up. This update
adds a suffix of the form "-GP" or "-HS" for production
devices, so that general purpose (GP) and high security
(HS) can be distiguished. Applies to all OMAP5 variants.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:37 -04:00
Daniel Allred
410f525794 spl: build: ti: add support for secure boot images
Updates the SPL build so that when CONFIG_TI_SECURE_DEVICE
is in use (which it should be when building for secure parts),
the TI secure development package is used to create a valid
secure boot image. The u-boot SPL build processes is NOT aware
of the details of creating the boot image - all of that information
is encapsulated in the TI secure development package, which is
available from TI. More info can be found in README.ti-secure

Right now, two image types are generated, MLO and X-LOADER. The types
are important, as certain boot modes implemented by the device's ROM
boot loader require one or the other (they are not equivalent). The
output filenames are u-boot-spl_HS_MLO and u-boot-spl_HS_X-LOADER. The
u-boot-spl_HS_MLO image is also copied to a file named MLO, which is
the name that the device ROM bootloader requires for loading from the
FAT partition of an SD card (same as on non-secure devices).

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:36 -04:00
Daniel Allred
883dfd1553 ti: AM43xx: config.mk: Add support for generating secure boot images
Modifies the config.mk to build secure images when building
the SPL for secure devices.

Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes. The same u-boot
binary file is processed slightly differently to produce a
different boot image, depending on whether the user wants to
boot off SPI, QSPI or other boot media.

Refer to README.ti-secure for more information.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:34 -04:00
Daniel Allred
0a0c534b33 ti: omap-common: Add commands for generating secure SPL images
Adds a centralized config_secure.mk in omap-common for
OMAP-style TI secure devices to use for boot image generation

Depending on the boot media, different images are needed for
secure devices. These commands generates u-boot*_HS_* files that
need to be used to boot secure devices.

Please refer to README.ti-secure for more information.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
a774e08858 ti: omap-common: Add Kconfig file for secure device support
Defines CONFIG_TI_SECURE_DEVICE which needs to be turned on
when building images for secure devices. This flag is used
to invoke the secure image creation tools for creating a
boot image that can be used on secure devices. This flag
may also be used to conditionally compile code specific
to secure devices.

This terminology will be used by all OMAP architecture devices,
hence introducing to a common location.

With the creation of Kconfig for omap-common, moved the
sourcing of the Kconfig files for the omap3/4/5 and am33xx
devices from arch/arm/KConfig to the omap-common one.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
6384726d2d arm: Kconfig: Add support for AM43xx SoC specific Kconfig
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.

This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.

Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
ce31ac7f72 arm: am33xx: Kconfig: Add secure device definitions
Adds a new Kconfig file for AM33xx class devices. We
need a common place to define CONFIG parameters
for these SOCs, especially for adding support
for secure devices.

a) Adds a definition for ISW_ENTRY_ADDR. This is the
address to which the ROM branches when the SOC
ROM hands off execution to the boot loader.
CONFIG_SYS_TEXT_BASE and CONFIG_SPL_TEXT_BASE are set
to this value for AM43xx devices.

b) Adds CONFIG_PUB_ROM_DATA_SIZE which is used to
calculate CONFIG_SPL_MAX_SIZE. This value indicates the
amount of memory needed by the ROM to store data during
the boot process.

Currently, these CONFIG options are used only by AM43xx,
but in future other AM33xx class SOCs will also use them.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:32 -04:00
Simon Glass
5c2dd4cd7a exynos: pwm: Add a driver for the exynos5 PWM
This driver supports the standard PWM API. There are 5 PWMs. Four are used
normally and the last is normally used as a timer.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 13:25:18 +09:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Peng Fan
04cb3c0b0e imx: mx6: correct get_cpu_speed_grade_hz for i.MX6DQP
Correct get_cpu_speed_grade_hz for i.MX6DQP, otherwise we
will get wrong speed grade info i.MX6DQP.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Peng Fan
e4d79dcaa4 imx: mx6: ddr: support i.MX6D/QPlus
Support i.MX6D/QPlus.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Peng Fan
b949fd2ccb imx: mx6: use simpler runtime cpu dection macros
Use simpler runtime cpu dection macros.
i.MX6DL and i.MX6SOLO work the same, so use is_mx6sdl.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Peng Fan
dea572379e imx: mx6: support i.MX6SOLO when enable/disable_ldb_di_clock_sources
i.MX6DL and i.MX6SOLO work the same, add i.MX6SOLO support
when enable/disable_ldb_di_clock_sources.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Qianyu Gong
56747bfdbd armv7: ls102xa: spl: fix the macro name of MMC mode
MMCSD_MODE_FAT has been renamed to MMCSD_MODE_FS by commit 205b4f33.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:46 -07:00
Peng Fan
d15a244b05 imx: correct speed grading info for i.MX6UL
Correct speed grading info for i.MX6UL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-18 09:47:41 +02:00
Stefan Agner
f716bf11f3 imx: imx7d: fix ahb clock mux 1
The clock parent of the AHB root clock when using mux option 1
is the SYS PLL 270MHz clock. This is specified in  Table 5-11
Clock Root Table of the i.MX 7Dual Applications Processor
Reference Manual.

While it could be a documentation error, the 270MHz parent is
also mentioned in the boot ROM configuration in Table 6-28: The
clock is by default at 135MHz due to a POST_PODF value of 1
(=> divider of 2).

Signed-off-by: Stefan Agner <stefan@agner.ch>
2016-05-17 17:52:20 +02:00
Russ Dill
b67d6b003c ARM: am33xx: Fix DDR initialization delays
The current delays in the DDR initialization routines for am33xx
architectures are sometimes not running long enough leading to DDR
init errors. On am437x, this shows up as an L3 NOC error after the
kernel boots. This is due to the timer not being initialized
properly, but instead still containing the timer init values from
the boot ROM which cause timers to expire in 1/4th the time
required.

timer_init is typically not called until board_init_r, however on
am33xx/am43xx udelay is required in sdram_init which is called
from board_init_f, so a call to timer_init is required earlier.

Note that this issue introduced in v2015.01 by:

b352dde "am33xx: Drop timer_init call from s_init".

Although this could instead fixed by reverting said commit, it
would cause timer_init to be called twice in both SPL and non-SPL
cases. This gives a little more fine grained control and also
matches what is being done on omap-command and fsl-layerscape.

Signed-off-by: Russ Dill <russ.dill@ti.com>
2016-05-06 10:10:20 -04:00
Tom Rini
821c89d38c Revert "omap3: Use raw SPL by default for mmc1"
Unfortunately with this change we now are unable to do FS mode boots
from MMC1 as with the way the code works today we will always load and
assume that the hard-coded raw location contains U-Boot.  Further, we
cannot fix this by just changing other logic to try FS-then-RAW as it
would also make us have to ignore what order the ROM is telling us to
try.

This reverts commit 22d90d560a.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-02 12:14:18 -04:00
Nishanth Menon
e52e334e5c ARM: DRA7: Add ABB setup for all domains
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:41 -04:00
Nishanth Menon
a818097a33 ARM: OMAP5: Enable ABB configuration for MM voltage domain
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:40 -04:00
Nishanth Menon
3708e78c33 ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structure
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.

Hence, move the txdone mask definition over to structure describing
voltage domain.

Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:39 -04:00
Nishanth Menon
2d9d057be6 ARM: OMAP5/DRA7: Get rid of control_std_fuse_opp_vdd_mpu_2
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.

This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.

Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:38 -04:00
Fabio Estevam
69cc7dbf1f Add initial support for Technexion's PICO-IMX6UL-EMMC board
Add support for Technexion's PICO-IMX6UL-EMMC board.

For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc

Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-19 16:37:36 +02:00
Akshay Bhat
90d7cc42b3 imx: mx6: Fix procedure to switch the parent of LDB_DI_CLK
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree,
the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the
ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is
generated, and the LVDS display will hang when the ipu_di_clk is sourced from
ldb_di_clk.

To fix the problem, both the new and current parent of the ldb_di_clk should
be disabled before the switch. This patch ensures that correct steps are
followed when ldb_di_clk parent is switched in the beginning of boot.

This patch was ported from the 3.10.17 NXP kernel
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d

NXP errata number: ERR009219, EB821

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-19 16:05:12 +02:00
Tom Rini
814013253f Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-04-13 07:19:50 -04:00
Hans de Goede
df120142f3 arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_INVAL_ALL) with asm code
Lets be consistent and also replace v7_maint_dcache_all()
with asm code for the invalidate case.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-11 20:48:27 -04:00
Hans de Goede
c09d29057a arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_CLEAN_INVAL_ALL) with asm code
v7_maint_dcache_all() does not work reliable when build with gcc6,
see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788

While debugging this I learned that v7_maint_dcache_all() is unreliable
when build with gcc5 too when it is marked as noinline.

This commit fixes the reliability issues by replacing the C-code with
the ready to use asm implementation from the kernel.

Given that this code when written as C-code clearly is quite fragile
(also see the existing comments about the C-code being the way it is
 to get optimal assembly) and that we have a proven asm alternative,
I believe that this is the best solution.

Note that we actually already had a copy of the kernel's
v7_flush_dcache_all() before this commit in
arch/arm/mach-uniphier/arm32/lowlevel_init.S.

This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames
it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper
which saves / restores the clobbered registers for use from C-code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-11 20:48:26 -04:00
Paul Kocialkowski
41582e2e77 sniper: Change vendor name from lge to lg, matching devicetree vendor prefix
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-04-01 17:18:06 -04:00
Alexander Graf
e6e505b93c sunxi: Move cpu independent code to mach directory
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.

Move all files that are not really tied to armv7 into a new mach-sunxi
directory.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Chen-Yu Tsai
0c935acb9e sunxi: usb_phy: Add support for A83T USB PHYs
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:04:06 +02:00
Hans de Goede
c74384c680 sunxi: Print soc-id from sram controller for sun8i boards
As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-31 14:26:52 +02:00
Hans de Goede
5f8afd704c sunxi: Add conditional magic sram poke for A33
I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-31 14:26:52 +02:00
Alexander Graf
d990f5c834 arm: Add support for HYP mode and LPAE page tables
We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.

Some boards however (like the RPi2) run in HYP mode. There, we need to modify
the HYP version of system registers and HYP mode only supports the long
descriptor PTE format.

So this patch introduces support for both long descriptor PTEs and HYP mode
registers.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-27 09:12:17 -04:00
Nishanth Menon
c755e67516 ARM: OMAP5/DRA7: Expose do_set_iodelay
do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:15 -04:00
Nishanth Menon
ceb7d77d6f ARM: OMAP5/DRA7: Split iodelay functionality into sub steps
Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.

While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:15 -04:00
Nishanth Menon
9c90f5135e ARM: DRA72: sdram: Update sdram ext phy configuration for SR2.0
Based on data from EMIF configuration tool 1.1.1.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:14 -04:00
Nishanth Menon
3d042e468a ARM: DRA7: hwdata: Update ioreg data for DRA72 SR2.0
Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been incorporated as well.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:13 -04:00
Ravi Babu
d851ad3a66 ARM: DRA72x: Add support for detection of SR2.0
Add support for detection of SR2.0 version of DRA72x family of
processors.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:12 -04:00
Peng Fan
7abeec2234 imx: mx7d: move MX7D to Kconfig entry
If including MX7D in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
 will not effect.So move MX7D to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX7D" to boards using i.MX7 Dual.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-26 14:16:12 +01:00
Peng Fan
9131c18cfa imx: mx6sx: move MX6SX to Kconfig entry
If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX6SX" to boards using i.MX6 SoloX.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-26 14:16:12 +01:00
Stefan Roese
a7f480d92d arm: mx6: Add CCV xPress board support
This patch add support for the CCV xPress board which is equipped
with the i.MX6UL. And provides the following interfaces:

- 128MiB DDR
- UART
- I2C
- eMMC (with booting)
- Ethernet
- USB

This patch adds two build targets. One with and one without SPL. The
non-SPL version is used for loading U-Boot via USB (imx_usb_loader).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-26 14:16:12 +01:00
Fabio Estevam
47173483a3 warp7: Add initial support
Add the basic support for Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platform

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-03-26 14:16:12 +01:00
Marek Vasut
b10d93ee9e arm: imx6: Switch DDR3 calibration to wait_for_bit()
Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit()
to generic implementation of wait_for_bit().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-03-25 14:01:29 +01:00
Peng Fan
d78e7f2794 imx: print ARM clock for clocks command
Default print ARM clock for clocks command.
Test on i.MX6UL 14x14 evk board:
"
=> clocks
PLL_SYS         792 MHz
PLL_BUS         528 MHz
PLL_OTG         480 MHz
PLL_NET          50 MHz

ARM          396000 kHz
"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-25 13:57:19 +01:00
Peng Fan
7082d87916 imx: mx6ul configure the PMIC_STBY_REQ pin as open drain
Configure the PMIC_STBY_REQ pin as open drain 100K according
to the design team's requirement for the PMIC_STBY_REQ pin
for i.MX 6UltraLite TO1.0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-25 13:56:55 +01:00
Peng Fan
e4dc3fc068 imx: mx6ul: skip setting ahb rate
To i.MX6UL, default ARM rate and AHB rate is 396M and 198M,
no need to set them.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-25 13:56:40 +01:00
Ye Li
b777789ebd imx: mx6: Fix incorrect clear mmdc_ch0 handshake mask
Since the MX6UL/SL/SX only has one DDR channel, in CCM_CCDR register
the bit[17] for mmdc_ch0 is reserved and its proper state should be 1.
When clear this bit, the periph_clk_sel cannot be set and that
CDHIPR[periph_clk_sel_busy] handshake never clears.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2016-03-25 13:55:54 +01:00
vishnupatekar
e449e840c5 sunxi: A83T: fix 32bit overflow warning
In mctl_channel_init, (0x50<<26) which overflows 32bit.
It was supposed to be 0x50<<16,corrected now.

Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Hans de Goede
fc8991c61c sunxi: Fix gmac not working due to cpu_eth_init no longer being called
cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.

This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().

The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.

Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>
2016-03-23 22:04:13 +01:00
Hans de Goede
60fa63012f sunxi: Add support for USB vbus pin for USB3
The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
1da598208d sunxi: Fix clock_twi_onoff for sun9i
Fix a copy and paste error which caused us to use the uart rather then
the twi reset bits in clock_twi_onoff for sun9i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
a93b0fe3fd sunxi: Fix clock_twi_onoff for sun8i-a83
clock_sun8i_a83.c did not contain a clock_twi_onoff implementation
at all, this is fixed by moving the clock_sun6i.c implementation,
which is correct for the a83 too, to a shared location.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
730d2f3a41 sunxi: Fix clock_twi_onoff for sun6i
The clock_sun6i.c implementation was not deasserting the reset for
the regular i2c controllers, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
583fede8ee sunxi: A23: Fix some revisions needing a different magic sram poke
I've had this one a23 tablet which would not boot and I've finally
figured out what the problem is by looking at the released boot0 code,
it seems the magic sram controller poke which we need to do in s_init()
depends on the revision of the a23.

Specifically this change is needed to get the A23 SoC I have with the
following serial to boot: "E6071AB 26Y7".

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Stefano Babic
312a6c016a Merge branch 'next' 2016-03-20 22:04:29 +01:00
Tom Rini
f8a4826383 spl: arm: Make sure to include all of the u_boot_list entries
Starting with 96e5b03 we use a linker list for partition table
information.  However since we use this in SPL we need to make sure that
the SPL linker scripts include these as well.  While doing this, it's
best to simply include all linker lists to future proof ourselves.

Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:27:55 -04:00
Tom Rini
f5af0827f2 arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX
On OMAP4 platforms that also need to calculate their DDR settings we are
now getting very close to the linker limit size.  Since OMAP44XX is only
seen with LPDDR2, remove some run time tests for LPDDR2 or DDR3 as we
will know that we don't have it for OMAP44XX.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:48 -04:00
Paul Kocialkowski
69847dd8f0 omap4: Check warm reset for reboot mode validity
Since the SAR registers are filled with garbage on cold reset, this checks for a
warm reset to assert the validity of reboot mode.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:54 -04:00
Paul Kocialkowski
faec3f9841 omap4: Reboot mode support
Reboot mode is written to SAR memory before reboot in the form of a string.

This mechanism is supported on OMAP4 by various TI kernels.

It is up to each board to make use of this mechanism or not.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:53 -04:00
Paul Kocialkowski
6e495a453f omap4: Properly enable USB PHY clocks
This correctly enables the USB PHY clocks, by enabling CM_ALWON_USBPHY_CLKCTRL
and correctly setting CM_L3INIT_USBPHY_CLKCTRL's value.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:50 -04:00
Paul Kocialkowski
5e56b0a80e omap-common: clocks-common: Setup USB DPLL when MUSB is in use
On (at least) OMAP4, the USB DPLL is required to be setup for the internal PHY
to work properly. The internal PHY is used by default with the MUSB USB OTG
controller.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:49 -04:00
Paul Kocialkowski
ae51b5709e Amazon Kindle Fire (first generation) codename kc1 support
The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011.

It is using an OMAP4430 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:48 -04:00
Paul Kocialkowski
14689ad79e omap4: Move i2c clocks enable to enable_basic_clocks
I2C is often enabled withing the U-Boot SPL, thus those clocks are required to
be enabled early (especially when the bootrom doesn't enable them for us).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:47 -04:00
Paul Kocialkowski
437086b1da omap4: Remove duplicate CM_L3INIT_USBPHY_CLKCTRL reference and whitespace
This removes a duplicate reference to CM_L3INIT_USBPHY_CLKCTRLin
enable_basic_uboot_clocks. Also, a doubled whitespace is removed.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:46 -04:00
Paul Kocialkowski
3832e54673 omap-common: Remove deprecated arch_cpu_init code
save_omap_boot_params is called from spl_board_init in the SPL context. Thus,
there is no reason to duplicate that call on arch_cpu_init.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:46 -04:00
Paul Kocialkowski
3ef56e61c8 omap-common: Rename set_muxconf_regs_essential to set_muxconf_regs
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:06 -04:00
Paul Kocialkowski
ed5ddebe96 omap4: Export jedec sdram timings
Individual boards might provide their own emif_get_device_timings function and
use the jedec timings in their own way, hence those have to be exported.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:11:32 -04:00
Paul Kocialkowski
96703acd0a omap4: Export elpidia sdram timings
Individual boards might provide their own emif_get_device_timings function and
use the elpidia timings in their own way, hence those have to be exported.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:11:31 -04:00
Paul Kocialkowski
7cb998ba85 omap4: Export elpidia sdram device details
Individual boards might provide their own emif_get_device_details function and
use elpidia device details in their own way, hence those have to be exported.

This also wraps existing definitions with the proper ifdef logic.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:11:30 -04:00
Paul Kocialkowski
90ca5dfec4 omap3: Use a define for reboot reason offset
This introduces a define for the offset to the reboot reason, rather than
hardcoding it.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-15 15:10:48 -04:00
Paul Kocialkowski
c5412b084b omap3: String-based reboot mode handling
This switches reboot mode handling to a string-based interface, that allows more
flexibility to set a common interface with the next generations of OMAP devices.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-15 15:10:47 -04:00
Tom Rini
4d339a9e8a Merge branch 'master' of git://git.denx.de/u-boot-video 2016-03-15 08:01:17 -04:00
Lokesh Vutla
a7638833b3 ARM: DRA7: Move emif settings to board specific files
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:50 -04:00
Lokesh Vutla
25afe55de5 ARM: DRA7: Enable EEPROM support
Enable EEPROM support for DRA74-evm.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:50 -04:00
Adam Ford
2f6ed3b89a ARM: Various: Future-proof serial platdata
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.

Tested on the Logic PD Torpedo + Wireless.

I only changed a handful of devices that used the same syntax as the Logic
board.  Appologies if I missed one or stepped on toes.  Thanks to Derald Woods
and Alexander Graf.

Signed-off-by: Adam Ford <aford173@gmail.com>

V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c

V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c

V4: Fix subject heading

V3: Remove  reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.

V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:48 -04:00
Lokesh Vutla
e850ed82bc ARM: OMAP4+: Allow arch specfic code to use early DM
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:48 -04:00
Lokesh Vutla
29c20ba235 ARM: DRA7: emif: Enable interleaving for higher address space
Given that DRA7/OMAP5 SoCs can support more than 2GB of memory,
enable interleaving for this higher memory to increase performance.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:47 -04:00
Lokesh Vutla
e3ce3aa103 ARM: DRA7: emif: Check for enable bits before updating leveling output
Read and write leveling can be enabled independently. Check for these
enable bits before updating the read and write leveling output values.
This will allow to use the combination of software and hardware leveling.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:47 -04:00
Lokesh Vutla
4571c519b4 ARM: DRA7: emif: Fix DDR init sequence during warm reset
Commit (20fae0a - ARM: DRA7: DDR: Enable SR in Power Management Control)
enables Self refresh mode by default and during warm reset the EMIF
contents are preserved. After warm reset EMIF sees that it is idle and
puts DDR in self-refresh. When in SR, leveling operations cannot be done
as DDR can only accept SR exit command, so its hanging during warm reset.
In order to fix this reset the power management control register before
EMIF initialization if it is a warm reset.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:46 -04:00
Lokesh Vutla
de09547478 ARM: DRA7: emif: Fix updating of refresh ctrl shadow
On DRA7, refresh ctrl shadow should be updated with
the final value.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:46 -04:00
Kipisz, Steven
212f96f6bd board: ti: AM57xx: Add detection logic for AM57xx-evm
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).

The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.

Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.

NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.

This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:35 -04:00
Kipisz, Steven
d88d6c8ccf ARM: OMAP4/5: Add generic board detection hook
Many TI EVMs have capability to store relevant board information
such as DDR description in EEPROM. Further many pad configuration
variations can occur as part of revision changes in the platform.
In-order to support these at runtime, we for a board detection hook
which is available for override from board files that may desire to do
so.

NOTE: All TI EVMs are capable of detecting board information based on
early clocks that are configured. However, in case of additional needs
this can be achieved within the override logic from within the board
file.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:34 -04:00
Kipisz, Steven
93e6253d11 ARM: OMAP4/5: Centralize early clock initialization
Early clock initialization is currently done in two stages for OMAP4/5
SoCs. The first stage is the initialization of console clocks and
then we initialize basic clocks for functionality necessary for SoC
initialization and basic board functionality.

By splitting up prcm_init and centralizing this clock initialization,
we setup the code for follow on patches that can do board specific
initialization such as board detection which will depend on these
basic clocks.

As part of this change, since the early clock initialization
is centralized, we no longer need to expose the console clock
initialization.

NOTE: we change the sequence slightly by initializing console clocks
timer after the io settings are complete, but this is not expected
to have any functioanlity impact since we setup the basic IO drive
strength initialization as part of do_io_settings.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:32 -04:00
Peng Fan
00b1d2d317 imx: mx6: hdmi: handle overflow condition
If HDMI_IH_FC_STAT2_OVERFLOW_MASK is set, we need to
do TMDS software reset and write to clear fc_invidconf register.
We need minimum 3 times to write to clear the fc_invidconf
register, so choose 5 loops here.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Sandor Yu <sandor.yu@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-14 22:53:45 +01:00
Fabio Estevam
e25a0656ba mx7: Distinguish between dual and solo versions
Read the number of cores in the fuses to distinguish between
the dual and solo versions.

Tested on a mx7d sabresd and on a mx7solo warp7.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-03-09 12:50:39 +01:00
Akshay Bhat
f9162b15c1 arm: imx: Add support for GE Bx50v3 boards
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-03-09 12:45:42 +01:00
Alexander Graf
22d90d560a omap3: Use raw SPL by default for mmc1
Now that we fall back to the FS code path when we don't find u-boot
at the raw sector offset, there is no good reason to not default to
raw boot.

With this patch, I can successfully boot u-boot from a raw sector
offset on beagle-xm.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-08 15:01:46 -05:00
Paul Kocialkowski
23a004a63f sniper: Various minor cleanups, missing Kconfig configs and reorganisation
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-29 14:49:37 -05:00
Tom Rini
e1417c7b66 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-02-24 18:44:15 -05:00
Alison Wang
a08b1921b4 armv7: ls102xa: Move smmu and stream id initialization into the common soc code
The initialization for smmu and stream id is moved into the common soc
code.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:15 -08:00
Jelle van der Waa
dc44fd8ae4 sunxi: H3: Add support for the host usb-phys
Add support for phy 1-3.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-02-23 20:59:10 +01:00
Tom Rini
595af9db24 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-02-21 07:56:16 -05:00
Peng Fan
35c4ce5e20 imx: mx7d: isolate resources to domain 0 for A7 core
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.

So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.

This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.

Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21 11:46:26 +01:00
Peng Fan
83703a1ccf imx: mx7: implement functions to boot auxiliary core
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.

arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.

Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21 11:46:26 +01:00
Peng Fan
0623d375cf imx: mx6: implement functions to boot auxiliary core
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.

arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.

Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21 11:46:26 +01:00
Peng Fan
677656bdb5 imx: mx7d: clock support for RDC
If CONFIG_IMX_RDC is enabled, enable clock for RDC and SEMAPHORE.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21 11:46:26 +01:00
Soeren Moch
1a43dc11a3 imx: mx6: Implement mmc_get_env_part
commit 216d286c7e [imx: mx6: implement
mmc_get_env_dev] introduced selection of the environment device according
to the boot device when booting from SD/MMC.

Extend this functionality for also selecting the device partition.

Signed-off-by: Soeren Moch <smoch@web.de>
2016-02-21 11:31:44 +01:00
Adam Ford
2cd1ff8403 OMAP3_LOGIC: Setup defconfig to enable SPL and NAND booting
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08 10:10:39 -05:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Peng Fan
216d286c7e imx: mx6: implement mmc_get_env_dev
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC.
Introduce a weak function board_mmc_get_env_dev, different
boards can implement it according to different sdhc controllers
that used by the board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-04 10:13:49 +01:00
Peng Fan
62d8cce9f3 imx: mx7dsabresd: move mmc_get_env_devno to soc code
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-04 10:13:45 +01:00
Ye Li
23e2da27d3 imx: mx6ul/sx: Fix issue in LCDIF clock dividers calculation
The checking with max frequency supported is not correct, because the temp
is calculated by max pre and post dividers. We can decrease any divider to
meet the max frequency limitation. Actually, the calculation below the codes
is doing this way to find best pre and post dividers.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-02 21:25:50 +01:00
Ye Li
9655ebdd50 imx: mx6sx: Fix issue in LCDIF clock enablement
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always
enter the -EINVAL return.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-02 21:25:05 +01:00
Ye Li
cf94a3427a imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO board
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.

Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02 21:04:21 +01:00
Ye Li
d4d1dd6749 mx6: soc: Add ENET2 mac address support
The i.MX6SX and i.MX6UL has two ENET controllers, add support for reading
MAC address from fuse for ENET2.

Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02 21:03:59 +01:00
Marek Vasut
d339f16911 arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code
fine-tunes the behavior of the MMDC controller in order to improve
the signal integrity and memory stability.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-02 20:58:46 +01:00
Marek Vasut
11aa6a32eb arm: cache: Implement cache range check for v7
Add code to aid tracking down cache alignment issues.
In case DEBUG is defined in the cache.c, this code will
check alignment of each attempt to flush/invalidate data
cache and print a warning if the alignment is incorrect.
If DEBUG is not defined, this code is optimized out.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
2016-01-31 16:32:56 +01:00
Tom Rini
82d72a1b99 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-01-28 18:42:10 -05:00
Bin Meng
afe6462da9 arm: ls102xa: Rewrite the logic of ft_fixup_enet_phy_connect_type()
eth_get_dev_by_index() is an API which is not available in driver
model. Use eth_get_dev_by_name() instead, which can also simplifly
the code logic a little bit.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:23:22 -06:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Vishnu Patekar
f3ad64c88c sunxi: Add support for LPDDR3 for A83T
Banana-pi M3 has LPDDR3 DRAM. this adds support for LPDDR3 for A83T.
Mostly the timing parameters are different from DDR3.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Vishnu Patekar
f5fd8caf7f sunxi: Groundwork to support new dram type for A83T
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.

This adds groundwork to support for new DRAM type for A83T.

Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Vishnu Patekar
627b380f62 sunxi: Redundant code cleanup from a83t dram init
This removes the redundant lines of code from mctl_sys_init.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Chen-Yu Tsai
9683945179 sunxi: Support PSCI ops on Allwinner H3
H3 has the same power sequencing procedure as the A31/A31s, which
includes the power clamps.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Chen-Yu Tsai
ed80584f30 sunxi: Support H3 CCU security switches
H3's CCU includes some switches which disable non-secure access to some
of the more critical clock controls, such as MBUS, PLLs, and main
platform busses.

Configure them to enable non-secure access.

For now the only SoC that has this feature is the H3. For other
platforms just use a default (weak) empty function so things do
not break.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Chen-Yu Tsai
5823664fb8 sunxi: Support Secure Memory Touch Arbiter (SMTA) in sun8i H3
Secure Memory Touch Arbiter is the same thing as the TrustZone
Protection Controller found on A31/A31s.

Access to many peripherals on the H3 can be controlled by the SMTA,
and the settings default to secure access only.

This patch supports the new settings, and sets them to allow non-secure
access.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:04 +01:00
Tang Yuantian
1ef7ac70e2 arm: ls1021a: Adjust sata register default values
Updated the default sata register values to enhance the
performance and stability.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:15 -08:00
Peng Fan
d9699de85c imx: mx7: default enable MDIO open drain
The management data input/output (MDIO) requires open-drain,
i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
this feature. So to TO1.1, need to enable open drain by setting
bits GPR0[8:7] for TO1.1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-24 12:15:14 +01:00
Peng Fan
9ba18ff8ef imx: mx6ul/sx: fix mmdc_ch0 clk calculation
Check "Figure 19-5. BUS clock generation" of i.MX 6SoloX Applications
Processor Reference Manual and "Figure 18-5. BUS clock generation" of
i.MX 6UltraLite Applications Processor Reference Manual. If mmdc clk
sources from pll4_main_clk(pll_audio), the calculation is wrong.

Fix mmdc_ch0 clk calculation. Also add PLL_AUDIO/VIDEO support
for decode_pll.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-24 12:13:21 +01:00
Tom Rini
6905f4d3c7 Merge git://git.denx.de/u-boot-dm 2016-01-21 11:49:49 -05:00
Jelle van der Waa
9d0826879e sunxi: Add support for the I2C controller which is part of the PRCM
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-01-21 07:30:01 +01:00
Mugunthan V N
28a6c01187 arm: omap-common: do not build timer when CONFIG_TIMER defined
To prepare timer driver to DM/DT conversion do not build the
exiting timer driver when CONFIG_TIMER is defined. But since
omap's SPL doesn't support DM yet so built timer driver only for
SPL build when CONFIG_TIMER is defined.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:21 -07:00
Ladislav Michl
bfb7cc3340 armv7: Add missing newline after OMAP die ID
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
2016-01-20 10:19:38 -05:00
Tom Rini
90345c92a8 am33xx/am43xx: Add platform data for GPIOs
On these platforms we have many cases of boards that enable device model
and GPIO support but do not enable OF_CONTROL and pass in a device tree
with the binary.  We need to bring in the platform data here as well.

Tested on Beaglebone Black.

Reported-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Francisco Aguerre <franciscoaguerre@gmail.com>
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-08 10:15:45 -05:00
Tom Rini
f1993ca066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-03 10:32:24 -05:00
Peng Fan
839479dda6 imx: ddr: drop duplicated debug info
Drop duplicated debug info for tcl.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-03 15:19:58 +01:00
Tom Rini
e6e3faa5c2 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-12-14 20:27:23 -05:00
Yao Yuan
6c4a1eba3f armv7/fsl-ls102xa: Workaround for DDR erratum A008514
This is a workaround for hardware erratum.
Write the value of 63b2_0042h to EDDRTQCFG will optimal the
memory controller performance.

The value: 63b2_0042h comes from the hardware team.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:32 +08:00
Yao Yuan
0b8bc6314e armv7: ls102xa: cci-400: Enable snoop and DVM message requests.
Enable snoop and DVM message on all CCI-400 slave ports. Setting
on disabled feature (snoop or DVM) is ignored by CCI-400.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
[York Sun: Add commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:56:53 +08:00
Tom Rini
312db9f75f armv7: omap-common: Rework SPL board_mmc_init()
Since the changes in a1e56cf the way that we had board_mmc_init()
structured for OMAP parts (so that we always report device 0) are no
longer functional.  For now, make the case of booting from the second
device initialize both devices (we have no devices that only have the
second device as MMC).  A further rework and consolidation of the
functions should be done at a later date.

Tested on Beaglebone Black (SD and eMMC boot).

Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-12-14 13:42:54 -05:00
Yao Yuan
762b353546 arm: ls102xa: enable all the snoop signal for masters.
Enable the IP feature's snoop signal to support
hardware snoop for cache coherence.

SNPCNFGCR contains the bits to drive snoop signal
for various masters.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:29 -08:00
Yao Yuan
7ba0261810 arm: ls1021a: merge SoC specific code in a separate file
Create a soc.c file to put the code for soc special settings.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:29 -08:00
Shengzhou Liu
0c028a0328 arm: ls102x: add get_svr and IS_SVR_REV helper
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00
Egli, Samuel
69b918b65d am33xx,ddr3: fix ddr3 sdram configuration
This patch fixes the DDR3 initialization procedure in
order to comply with DDR3 standard. A 500 us delay is specified
between the DDR3 reset and clock enable signal. Until now,
this delay was not respected. Some DDR3 chips don't bother
but the bigger the RAM becomes the more likely it seems that
this delay is needed. We observed that DRAM > 256 MB from
the manufacturer Samsung have an issue when the specification
is not respected.

Changes:

1) Add a 1 ms wait for L3 timeout error trigger

2) Don't delay DDR3 initialization
Bit 31 of emif_sdram_ref_ctrl shouldn't be set because his
suppresses the initialization of DDR3

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: James Doublesin <doublesin@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
2015-12-12 15:56:09 -05:00
Jens Kuske
bb3654629a sunxi: Fix H3 DRAM DQ read delay configuration
The read delays were set incorrectly, leading to reliability
issues at higher DRAM clock speeds. This commit adjusts this
to match the vendor boot0 behaviour.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 15:45:48 +01:00
Olliver Schinagl
23baf66f25 sun4i: clock: Cleanup some whitespace errors
Add some spaces around operators.

Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 15:45:48 +01:00
Olliver Schinagl
887e2fd9da sunxi: twi: Enable clocks on sun7i
Commit 6c739c5d added code to enable i2c bus 4 and 5 on the sun7i SoC
but forgot to extend the range check in clock_twi_onoff, resulting in
the clock not getting enabled.

The range-check is not needed at all, since clock_twi_onoff only gets
called with such high indexes when CONFIG_I2C3_ENABLE / CONFIG_I2C4_ENABLE
is set and Kconfig already only allows these on sun6i / sun7i.

This commit removes the range-check all together fixing i2c bus 4 and 5
not working on sun7i.

Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
[hdegoede@redhat.com] Remove range check instead of extending it
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 15:45:48 +01:00
vishnupatekar
81f50d93cb sunxi: Add support for Allwinner A83T DRAM
Add support for A83T dram. Register are different from sun8i A33.
init code is similar to A33 dram init.
hope we'll shift duplicate code in dram_sun8i_*
to dram helper in future.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 15:45:47 +01:00
vishnupatekar
f542948b1e sunxi: clk: add basic clocks for A83T
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com] Fix PLL6 init to run at 600 MHz instead of 288 MHz,
fixing the mmc support not working
[hdegoede@redhat.com] Fix PLL init code to properly wait for the PLL-s to
stabilize, fixing cold-booting directly from sdcard not working
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 15:45:47 +01:00
vishnupatekar
95ab8fee8a sunxi: power: enabled support for axp818
Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 11:14:22 +01:00
vishnupatekar
d5a3357f1b sunxi: Add support for UART0 in PB pin group on A83T
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 11:14:21 +01:00
vishnupatekar
762e24a078 sunxi: Add Machine Support for A83T SOC
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.

SMP is not yet supported.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 11:14:21 +01:00
Jeroen Hofstee
0ff47e590b imx: mx6: add missing return value
cc: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-12-07 14:59:25 +01:00
Tom Rini
75507d5d54 am33xx: Update serial pdata
We now want to make sure that we have the platform data for NS16550 when
we do not have OF_CONTROL set.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-06 16:38:05 -05:00
Tom Rini
a85670e40d Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-12-04 08:21:28 -05:00
Tom Rini
1670c8c219 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-11-30 15:18:30 -05:00
Alison Wang
a1399534f1 arm: ls1021a: Ensure Generic Timer disabled before jumping into the OS
This patch addresses a problem mentioned recently on this mailing list:
[1].

In that posting a LS1021 based system was locking up at about 5 minutes
after boot,but the problem was mysteriously related to the toolchain
used for building u-boot.Debugging the problem reveals a stuck
interrupt 29 on the GIC.

It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.This causes the timer compare to fire 344 seconds
after u-boot configures it.Depending on how fast u-boot gets the
kernel booted,this amounts to about 5-minutes of Linux uptime before
locking up.

Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.

To fix the above issue, the generic physical timer is disabled
before jumping to the OS.

[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html

Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:01 -08:00
Alison Wang
2b714cfad4 arm: ls1021a: Ensure LS1021 ARM Generic Timer CompareValue Set 64-bit
This patch addresses a problem mentioned recently on this mailing list:
[1].

In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot.  Debugging the problem reveals a stuck
interrupt 29 on the GIC.

It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.  This causes the timer compare to fire 344 seconds
after u-boot configures it.  Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.

Apparently the bug is masked by some toolchains.  Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.

[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html

Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:01 -08:00
Minkyu Kang
225f5eeccd arm: s5pc1xx: move SoC to mach-s5pc1xx
move arm/arm/cpu/armv7/s5pc1xx to arch/arm/mach-s5pc1xx

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-30 17:17:01 +09:00
Ye.Li
90447ef03c mx6: clock: Modify GPMI clock to support mx6sx
On mx6sx, the CCM register bits for GPMI are different as other
mx6 platforms. Modify the GPMI clock function to support mx6sx.

Signed-off-by: Ye.Li <B37916@freescale.com>
2015-11-25 11:40:04 +01:00
Otavio Salvador
d7140351c2 cgtqmx6eval: Add SPL support
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.

Add SPL support so that all the variants can be supported

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-25 09:41:29 +01:00
Vignesh R
71cbed31f4 am33xx: Remove serial_init in s_init for QSPI/NOR XIP boot
serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().

Tested on AM437x IDK EVM with QSPI XIP boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-23 11:01:53 -05:00
Siarhei Siamashka
52d093112a sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.

PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.

The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
0404d53f2f sunxi: Add H3 DRAM initialization support
Based on existing A23/A33 code and the original H3 boot0.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
1c27b7dcd0 sunxi: Add basic H3 support
Add initial sun8i H3 support, only uart + mmc are supported for now.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:30:59 +01:00
Nikita Kiryanov
a1e56cf6d4 spl: mmc: add support for BOOT_DEVICE_MMC2
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.

Make SPL take into account the correct mmc device.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-18 14:50:05 -05:00
Nikita Kiryanov
36afd45136 spl: change return values of spl_*_load_image()
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.

Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-18 14:50:02 -05:00
Kipisz, Steven
74cc8b097d board: ti: beagle_x15: Rename to indicate support for TI am57xx evms
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).

Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728

The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.

Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.

NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.

As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-11-18 08:47:03 -05:00
Peng Fan
eb111bb31d imx: mx6: implement reset_misc
We need to power down lcdif before uboot reset to make reset can pass
stress test.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:53 +01:00
Peng Fan
ad153782e0 imx: mx6: add clock api for lcdif
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:53 +01:00
Peng Fan
7de4703691 mx7: psci: add basic psci support
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:31:16 +01:00
Stefano Babic
5f5620ab26 Merge git://git.denx.de/u-boot 2015-11-12 17:13:26 +01:00
Przemyslaw Marczak
fdbb740d7c s5p: cpu_info: print "cpu-model" if exists in dts
The CPU name for Exynos was concatenated with cpu id,
but for new Exynos platforms, like Chromebook Peach Pi
based on Exynos5800, the name of SoC variant does not
include the real SoC cpu id (0x5422).

For such case, the CPU name should be defined in device tree.

This commit introduces new device-tree property for Exynos:
- "cpu-model" - with cpu name string
If defined, then the cpu id is not printed.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-11-02 10:37:59 +09:00
Adrian Alonso
bb955146f0 arm: imx: add secure boot fuse details for imx7 SoC
Add secure boot fuse details (location) bank = 1, word = 3;
for imx7 SoC platforms.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-10-30 15:22:36 +01:00
Adrian Alonso
6b50bfe56d arm: imx: add secure boot fuse details for imx6 SoC
Add secure boot fuse details (location) bank = 0, word = 6;
for imx6 SoC platforms.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-10-30 15:22:36 +01:00
Adrian Alonso
6d846c726b imx: hab: rework unified rom section for mx7
Rework unified section macro select via Kconfig option
instead of macro definition in mx7_common header file.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-10-30 15:22:36 +01:00
Adrian Alonso
a89729c9ca imx: hab: use unified rom section for mx6sx and mx6ul
Add CONFIG_ROM_UNIFIED_SECTIONS for mx6sx and mx6ul target
platforms to resolve corresponding HAB_RVT_BASE base address,
the RVT table contains pointers to the HAB API functions in
ROM code.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-10-30 15:20:57 +01:00
Adrian Alonso
7a7281a91c imx: hab: rework secure boot support for imx6
Rework secure boot support for imx6, move existing hab support
for imx6 into imx-common for SoC reuse.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-10-30 15:20:57 +01:00
tang yuantian
4632ad773e arm: ls1021a: Add sata support on qds and twr board
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:02 -07:00
horia.geanta@freescale.com
5757e06c69 arm: ls102xa: enable snooping for CAAM transactions
Enable snooping for CAAM read & write transactions by
programming the SCFG snoop configuration register:
SCFG_SNPCNFGCR[SECRDSNP]
SCFG_SNPCNFGCR[SECWRSNP]

Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:33:58 -07:00
Alison Wang
0cbba8e953 ls102xa: fdt: Disable IFC in SD boot for QSPI
As QSPI/DSPI and IFC are pin multiplexed, IFC is disabled
in SD boot for QSPI. This patch will add fdt support for
this rule.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:33:56 -07:00
Paul Kocialkowski
2da87ab353 omap-common: Common get_board_serial function to pass serial through ATAG
Since there is a common function to grab the serial number from the die id bits,
it makes sense have one to parse that serial number and feed it to the serial
ATAG.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:18:31 -04:00
Paul Kocialkowski
679f82c349 omap-common: Common function to display die id, replacing omap3-specific version
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:18:30 -04:00
Paul Kocialkowski
07815eb9f3 omap-common: Common serial and usbethaddr functions based on die id
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:22 -04:00
Paul Kocialkowski
9fd5401659 omap5: omap_die_id support
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:21 -04:00
Paul Kocialkowski
987a40d52e omap4: omap_die_id support
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:20 -04:00
Paul Kocialkowski
b50a768528 omap3: omap_die_id support
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:18 -04:00
Paul Kocialkowski
72931b15e7 omap-common: Common omap_die_id definition
This introduces a common definition for omap_die_id, that aims at providing a
common interface for accessing omap platform's die id bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:17 -04:00
Maxime Ripard
f7d6b3cc16 sunxi: board: Only try to use the MMC related functions if enabled
So far, even if CONFIG_MMC was not enabled the board code was trying to use
the MMC-related functions, resulting in linker errors.

Protect those calls by an ifdef.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-10-20 22:48:28 +02:00
Hans de Goede
6944aff1ca sunxi: power: Unify axp pmic function names
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-10-20 18:40:27 +02:00
Hans de Goede
6d0bdfdde5 sunxi: Switch to using malloc_simple for the spl
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-20 18:40:27 +02:00
Fabio Estevam
f861f51c46 ls102xa: Fix reset hang
Since commit 623d96e89aca6("imx: wdog: correct wcr register settings")
issuing a 'reset' command causes the system to hang.

Unlike i.MX and Vybrid, the watchdog controller on LS102x is big-endian.

This means that the watchdog on LS1021 has been working by accident as
it does not use the big-endian accessors in drivers/watchdog/imx_watchdog.c.
Commit 623d96e89aca6("imx: wdog: correct wcr register settings") only
revelead the endianness problem on LS102x.

In order to fix the reset hang, introduce a reset_cpu() implementation that
is specific for ls102x, which accesses the watchdog WCR register in big-endian
format. All that is required to reset LS102x is to clear the SRS bit.

This approach is a temporary workaround to avoid a regression for LS102x
in the 2015.10 release. The proper fix is to make the watchdog driver
endian-aware, so that it can work for i.MX, Vybrid and LS102x.

Reported-by: Sinan Akman <sinan@writeme.com>
Tested-by: Sinan Akman <sinan@writeme.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-10-12 12:56:32 -04:00
Ian Campbell
e392b923ed arndale: Apply Cortex-A15 errata #773022 and #774769
We run 4 Arndale boards in our automated test framework, they have
been running quite happily for quite some time using a Debian Wheezy
userspace.

However when upgrading to a Debian Jessie we started seeing frequent
segmentation faults from gcc when building the kernel, to the extent
that it is unable to successfully build the kernel twice in a row, and
often fails on the first attempt.

Searching around I found https://bugs.launchpad.net/arndale/+bug/1081417
which pointed towards http://www.spinics.net/lists/kvm-arm/msg03723.html
and CPU Errata 773022 and 774769.

This errata needs to be applied to all processors in an SMP system,
meaning that the usual strategy of applying them in
arch/arm/cpu/armv7/start.S is not appropriate (since that applies to
the boot processor only). Instead we apply these errata in the secure
monitor which is code that is traversed by all processors as they are
brought up.

The net affect on Arndale is that ACTLR changes from 0x40 to
0x2000042. I ran 17 kernel compile iterations overnight with no
segfaults.

Runtime testing was done on our v2014.10 based branch and forward
ported (with only minimal and trivial contextual conflicts) to current
master, where it has been build tested only.

I suppose in theory these errata apply to any Exynos5250 based boards,
but Arndale is the only one I have access to and I have therefore
chosen to be conservative and only apply it there.

Also, reorder CONFIG_ARM_ERRATA_794072 in README to make the list
numerically sorted.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
2015-10-11 17:12:11 -04:00
Tom Rini
b8d242121d Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-10-02 09:38:44 -04:00
Peng Fan
e2748b4167 imx: mx6: correct enable_fec_anatop_clock
We should follow 'read->set/clr bit->write' flow for enable_fec_anatop_clock,
otherwise we may overridden configuration before enable_fec_anatop_clock.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-10-02 10:42:31 +02:00
Bernhard Nortmann
af654d1461 sunxi: retrieve FEL-provided values to environment variables
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.

misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().

The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.

Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-29 11:50:07 +02:00
Hans de Goede
cb42d63554 sunxi: Simplify spl board_init_f function
crt0.S will both memset the bss sectioan and call board_init_r for us,
so there is no need to do either ourselves.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-29 11:50:07 +02:00
Peng Fan
f697c2acca imx: fix coding style
Fix coding style.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-24 11:32:38 +02:00
Peng Fan
d449701b83 imx: mx7: discard unused global variable
Discard unused global variable.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-24 11:31:37 +02:00
Peng Fan
f05f4528f2 imx: mx7: drop select CPU_V7 for board target
drop select CPU_V7 for board target, since ARCH_MX7 selects CPU_V7.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-20 09:55:11 +02:00
Stefan Roese
68282f55b8 arm: Remove unused ST-Ericsson u8500 arch
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.

Please note that this patch also removes these config options:

- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT

As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.

If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-15 15:05:21 -04:00
Tom Rini
850f788709 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2015-09-13 17:25:16 -04:00
Peng Fan
ada5771f09 imx: mx6 discard 'select CPU_V7' for different targets
Discard the 'select CPU_V7' from Kconfig in arch/arm/cpu/armv7/mx6
for different targets, because ARCH_MX6 selects CPU_V7.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-13 10:38:48 +02:00
Peng Fan
d9cbb264e8 imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
   supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.

This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
   CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
   part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
   so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
   mx6ul_14x14_evk. And we have no way to dymaically checking this chip
   is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
   POWER related configurations also effect for mx6ul_14x14_evk. But
   power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
   do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
   configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
   according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry

Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img

U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)

CPU:   Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C:   ready
DRAM:  256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:   FEC1
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-13 10:32:44 +02:00
Peng Fan
0eca9f6f0d Revert "imx: mx6: ddr correct tRFC and tXS"
This reverts commit 059323fb6a8f21637bb617919715c2427f24777c.

This commit 059323fb6a8f21637bb617919715c2427f24777c use JESD79-3E which
is not the newest spec. Should use JESD79-3F in which tRFC is 260ns for
4Gb chip.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
2015-09-13 10:26:45 +02:00
Adrian Alonso
1a8150d4b1 imx: mx7dsabresd: Add support for MX7D SABRESD board
* Add i.MX7D SABRESD target board support with enabled modules:
  UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.

  Build target: mx7dsabresd_config

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-09-13 10:11:54 +02:00
Adrian Alonso
cd562c8d07 imx: imx7d: add imx-common cpu support for imx7d
Add imx-common cpu support for imx7d SoC
- Update reset_cause for imx7d
- Enable watchdog driver built for imx7d

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-09-13 10:11:54 +02:00
Adrian Alonso
648539c906 arm: imx-common: init: rework wdog settings for imx6/imx7
Rework imx_set_wdog_powerdown to be reused by imx6 and imx7

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-09-13 10:11:54 +02:00
Adrian Alonso
c5752f73a5 imx: imx7d: Add SoC system support
Add imx7d basic SoC system support
Misc arch dependent functions for system bring up

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
2015-09-13 10:11:53 +02:00
Adrian Alonso
7bebc4b04e imx: imx7d: clock control module support
* Add Clock control module (CCM) support
* iMX7D SoC introduces 3 main clock sysmtem abstraction for clock
  root frequency generation denominated clock slices.
  Core clock slice: hihg speed clock for ARM core
  Bus clock slice: for bus clocks
  IP clock slice: Peripheral clocks
* At system boot ROM enables PLL_ARM, PLL_DDR, PLL_SYS, PLL_ENET
  In u-boot, we have to:
  - Configure PFD3- PFD7 for freq we needed in u-boot
  - Set clock root for peripherals (ip channel)

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
2015-09-13 10:11:53 +02:00
Adrian Alonso
50a082a88c arm: imx: imx-common: init: move arch init common setup
Move common imx6 arch init setup, init.c can be extended
and reused to support imx7 SoC keeping init arch common
code.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-09-13 10:11:53 +02:00
Adrian Alonso
ab09e72866 arm: imx: common rework cache settings for imx6
Rework cache settings for imx6, move cache configuration
to imx-common/cache.c so it can be reused for newer SoC

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-09-13 10:11:53 +02:00
Adrian Alonso
1368f99346 thermal: imx_thermal: rework driver to be reused
Rework imx_thermal driver to be used across i.MX
processor that support thermal sensor

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-09-13 10:11:53 +02:00
Simon Glass
93b25c0813 arm: Remove omap3_sdp3430 board
This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:56:52 -04:00
Simon Glass
8dc372f93b arm: Remove omap3_mvblx board
This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:56:51 -04:00
Simon Glass
5ff33d0404 arm: Remove dig297 board
This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:11:12 -04:00
Lokesh Vutla
d6927a5d10 ARM: DRA7: emif: Fix disabling/enabling of refreshes
clrsetbits_le32/clrbits_le32 takes mask of the bits as input that
are needed to be set/clear. But emif driver passes the shift of the bits.
Fixing it here.

Reported-by: Mark Mckeown <m-mckeown@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-09-11 14:05:36 -04:00
Tom Rini
c9feb427ab Merge git://git.denx.de/u-boot-rockchip 2015-09-03 14:57:09 -04:00
Sjoerd Simons
81b0618ddf arm: Turn of d-cache before i-cache
Booting the kernel fails on RK3288 (and probably other rockchip SoCs)
when the i-cache is disabled/flushed before d-cache.

I have not investigated whether this is due to U-Boot hanging or whether
it's very early in the linux boot, but following the approach of the
various rockchip U-Boot forks (first disable d-cache then i-cache) makes
things work.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-02 21:28:25 -06:00
Adam Ford
7b77b1f63b Convert omap3_logic to ti_omap3_common.h
Convert to using the common config files.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-09-02 11:33:20 -04:00
Peng Fan
37cf215253 imx: vf610 add get_cpu_rev
Since we need to support runtime check for different drivers, we need
to add get_cpu_rev for vf610, otherwise there will be build errors.

This patch introduces a dummy CPU id which is not read from chip
silicon. Later when we can get the real id from chip, can fix the
value of MXC_CPU_VF610 then.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Suggested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-09-02 15:39:51 +02:00
Heiko Schocher
9627084c23 arm, imx6: add aristainetos 2b board version
there is a 2b board version of the aristainetos2
board. Differences to the v2:

- spi cs for the nor flash and display controller
  changed
- some pinmux changes
- LED gpio settings changed

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-09-02 15:38:16 +02:00
Peng Fan
d5b2112e75 imx: mx6ul_14x14_evk select MX6UL
There is no need to expose SoC choice to user, we already got
the SoC according to the build target. So default "select MX6UL"
for MX6UL_14x14_EVK target.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-02 15:34:13 +02:00
Peng Fan
e7d3b21bb7 imx: mx6slevk: add SPL support
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.

Boot Log:

U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img

U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)

CPU:   Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C:   ready
DRAM:  1 GiB
PMIC:  PFUZE100 ID=0x10
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-02 15:34:13 +02:00
Peng Fan
eb796cbb69 imx: mx6: ddr: add LPDDR2 support
Add LPDDR2 support:
1. Implement a function mx6_lpddr2_cfg to initialize MMDC for LPDDR2.
2. Introduce a structure mx6_lpddr2_cfg, most entrys are same to
   mx6_ddr3_cfg, but still keep it a single one for easy to choose
   parameters for LPDDR2.
3. If ddr_type is LPDDR2, use mx6_lpddr2_cfg to init MMDC.
4. Update comments.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
2015-09-02 15:34:12 +02:00
Peng Fan
f2ff834365 imx: mx6: ddr init MMDC according to ddr_type
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.

Initialize ddr_type for different boards which enable SPL.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-09-02 15:34:12 +02:00
Peng Fan
1b811e285c imx: mx6: ddr add dram io configuration and header file for i.MX6SL
Define two structure mx6sl_iomux_ddr_regs and mx6sl_iomux_grp_regs.
Add a new function mx6sl_dram_iocfg to configure dram io.
Add header file to define macros for register address.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-02 15:34:12 +02:00
Peng Fan
2cd8cd06bb imx: mx6: ddr correct tRFC and tXS
To Chip density 4Gb, tRFC should be 300ns, see
"Table 61 — Refresh parameters by device density" of JESD79-3E.
tXS(min) is max(5nCK, tRFC(min) + 10ns).

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-09-02 15:34:12 +02:00
Peng Fan
24139754f5 imx: mx6: ddr no support MMDC1 for i.MX6SL
i.MX 6SoloLite only supports MMDC0, so do not access MMDC1 for i.MX 6SL.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-09-02 15:34:12 +02:00
Soeren Moch
c3f871c176 tbs2910: use full name in Kconfig board selection
Signed-off-by: Soeren Moch <smoch@web.de>
2015-09-02 15:34:11 +02:00
Peng Fan
6d97dc10a8 imx: clock support enet2 anatop clock support
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
   To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-09-02 15:29:14 +02:00
Peng Fan
21782828f9 imx: mx6 move TARGET_xx Kconfig option to mx6 specific Kconfig file
Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig.
Add enable "CONFIG_ARCH_MX6" for boards based on mx6.
Then we can choose target boards using "make ARCH=arm menuconfig"
with ARCH_MX6 defined.

If using original way, we have no chance to enable ARCH_MX6 when
"make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig,
kconfig will complains "arch/../configs/platinum_titanium_defconfig:3:
warning: override: TARGET_PLATINUM_TITANIUM changes choice state"

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Soeren Moch <smoch@web.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-09-02 15:29:14 +02:00
Vladimir Barinov
21871138b7 arm: rmobile: Add Stout board support
Stout is an entry level development board based on R-Car H2 SoC (R8A7790)

This commit supports the following peripherals:
- SCIFA, I2C, Ethernet, QSPI, SDHI0/2, CPLD

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-08-31 17:32:59 +09:00
Chen-Yu Tsai
92369844ec sunxi: Enable non-secure access to RTC on sun6i (A31s)
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.

On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-31 08:43:42 +02:00
Kishon Vijay Abraham I
504de98a3b ARM: OMAP5/AM43xx: remove enabling USB clocks from enable_basic_clocks()
Now that we have separate function to enable USB clocks, remove
enabling USB clocks from enable_basic_clocks(). Now board_usb_init()
should take care to invoke enable_usb_clocks() for enabling
USB clocks.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:22 -04:00
Kishon Vijay Abraham I
09cc14f4bc ARM: AM43xx: Add functions to enable and disable USB clocks
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.

Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:21 -04:00
Kishon Vijay Abraham I
ca5a0f172e ARM: OMAP5: Add functions to enable and disable USB clocks
Added functions to enable and disable USB clocks which can be invoked
during USB init and  USB exit respectively.

Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:21 -04:00
Kishon Vijay Abraham I
7beaf8b690 ARM: DRA7: Enable clocks for USB OTGSS2 and USB PHY2
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:19 -04:00
Paul Kocialkowski
8ceb34a1d1 omap-common: SYS_BOOT fallback logic correction and support for more devices
The SYS_BOOT-based fallback shouldn't only check for one of the conditions of
use and then let the switch/case handle each boot device without enforcing the
conditions for each type of boot device again.

For instance, this behaviour would trigger the fallback for UART when
BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should
be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not
CONFIG_SPL_USB_SUPPORT.
Separating the logic for USB and UART solves this.

In addition, this adds support for more peripheral devices (USBETH and CPGMAC)
to the fallback mechanism. Note that the USBETH boot device should always be
different from the USB boot device (each should match a different bootrom
handoff case).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2015-08-28 12:33:18 -04:00
Nishanth Menon
76cff2b108 ARM: DRA74-evm: Use SMA_1 spare register to workaround DP83865 phy on SR2.0
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.

Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.

NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:13 -04:00
Nishanth Menon
c1ea3bece2 ARM: DRA7: Add detection of ES2.0
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp

[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:12 -04:00
Masahiro Yamada
dffb86e468 of: flip CONFIG_SPL_DISABLE_OF_CONTROL into CONFIG_SPL_OF_CONTROL
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.

Now, there are three boards enabling OF_CONTROL on SPL:
 - socfpga_arria5_defconfig
 - socfpga_cyclone5_defconfig
 - socfpga_socrates_defconfig

This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-08-18 13:46:04 -04:00
Tom Rini
952bd79b53 Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-08-18 08:25:24 -04:00
Vignesh R
5b3b0d687e ARM: AM43XX: Add functions to enable and disable EDMA3 clocks
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Vignesh R
8a09cfe14b ARM: OMAP5: Add functions to enable and disable EDMA3 clocks
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Kishon Vijay Abraham I
16ca1d09e6 ARM: OMAP5: Add support for disabling clocks in uboot
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Kishon Vijay Abraham I
fca45722fb ARM: AM43xx: Add support for disabling clocks in uboot
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Thomas Abraham
77b55e8cfc ARM: exynos: move SoC sources to mach-exynos
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.

Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-08-17 13:06:52 +09:00
Hans de Goede
55ea98d8b1 sun6i: clock: Add support for the mipi pll
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:39 +02:00
Hans de Goede
49043cbad1 sunxi: clock: Add clock_get_pll3() helper function
Add a helper function to get the pll3 clock rate.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:38 +02:00
Tom Rini
b5d92ba1ad ARM: SPL: Use CONFIG_SPL_DM not CONFIG_DM
We now have the CONFIG_SPL_DM for code within SPL to toggle caring about
DM or not.  Without this change platforms that do enable CONFIG_DM but
not CONFIG_SPL_DM may be broken (such as OMAP5).

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:48:07 -04:00
Tom Rini
0a9e34056f gpio: omap: Drop 'method' parameter
The "method" parameter was part of the original port of the driver from
the kernel.  At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do).  At this point however it's
just extra overhead, so drop.

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:48:06 -04:00
Tom Rini
1480fdf8a6 am33xx: Update DT files, add am335x_gp_evm_config target
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
  via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
  also enabled really.  We can just push GPIO to coming from DT

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:48:06 -04:00
Nikita Kiryanov
6ff31a7f70 arm: am43xx: enable spi clock
Add spi clock to the list of am43xx basic clocks to make the SPI
subsystem available on am43xx systems.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-12 20:48:03 -04:00
Nishanth Menon
095a5ef88e ARM: DRA72: disable workaround for 801819
DRA72x processor variants are single core and it does not export ACP[1].
Hence, we have no source for generating an external snoop requests which
appear to be key to the deadlock in DRA72x design.

Since we build the same image for DRA74x and DRA72x platforms, lets
runtime detect and disable the workaround (in favor of performance) on
DRA72x platforms.

[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438i/BABIAJAG.html

Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2015-08-12 20:47:50 -04:00
Nishanth Menon
1bbb556a6a ARM: DRA7/ OMAP5: implement Auxiliary Control Register configuration
Implement logic for ACR(Auxiliary Control Register) configuration using
ROM Code smc service.

Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2015-08-12 20:47:50 -04:00
Nishanth Menon
a615d0be6a ARM: Introduce erratum workaround for 801819
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "

Recommended workaround is as follows:
Do both of the following:

1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.

For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:

3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111

So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.

Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.

Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.

Based on ARM errata Document revision 18.0 (22 Nov 2013)

Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2015-08-12 20:47:49 -04:00
Wu, Josh
633b6ccedf ARM: cache: implement a default weak flush_cache() function
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.

In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.

So in this patch remove such code in flush_cache() and only call
flush_dcache_range().

Signed-off-by: Josh Wu <josh.wu@atmel.com>
2015-08-12 20:47:48 -04:00
Wu, Josh
387871a10e ARM: cache: add an empty stub function for invalidate/flush dcache
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.

To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-08-12 20:47:47 -04:00
Paul Kocialkowski
0257930ba0 LG Optimus Black (P970) codename sniper support
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.

It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.

For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:47:37 -04:00
Paul Kocialkowski
a08af85f46 omap3: Reboot mode support
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.

This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.

It is up to each board to make use of this mechanism or not.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:47:36 -04:00
Hans de Goede
c9f8947e66 sunxi: usb-phy: Never power off the usb ports
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.

Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.

This patch removes the powering off calls, fixing the undesirable power
bouncing.

Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-08 16:26:19 +02:00
Simon Glass
d1de41d7fa exynos: Add support for spring
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-05 21:06:17 -06:00
Simon Glass
71db6341c5 exynos: Tidy up CPU frequency display
Line up the display with the line below, e.g.:

	CPU:   Exynos5250 @ 1.7 GHz
	Model: Google Spring
	DRAM:  2 GiB
	MMC:   EXYNOS DWMMC: 0

Also show the speed as GHz where appropriate.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-05 21:06:14 -06:00
Simon Glass
a507454b13 exynos: Add support for the DisplayPort hotplug detect
Allow this function to be selected using the pinmux API.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-05 21:06:14 -06:00
Simon Glass
7fb57396e6 exynos: Enable the debug UART in SPL
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-05 21:06:11 -06:00
Paul Kocialkowski
95de1e2f26 usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSB
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-08-05 17:20:34 +02:00
Wang Dongsheng
6f0586e692 armv7/ls102xa: Fix non-boot cpus cannot correctly fall in spin table
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.

Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.

Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-08-03 12:06:37 -07:00
Tom Rini
7a1af7a79b Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-08-02 07:40:37 -04:00
Peng Fan
a462c34602 imx:mx6ul add dram spl configuration and header file
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
   only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
   runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
   IO configuration.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-08-02 11:05:09 +02:00
Peng Fan
db1c217c85 imx: mx6ul update soc related settings
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
2015-08-02 11:05:08 +02:00
Peng Fan
a2c74aaf51 imx: mx6ul select SYS_L2CACHE_OFF
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-08-02 11:05:08 +02:00
Peng Fan
43cb127b75 imx:mx6ul add clock support
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
   MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
   but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
   sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
   || defined....", only need one CONFIG_PCIE_IMX in header file.

Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-08-02 11:05:07 +02:00
Nikita Kiryanov
09a096992b arm: mx6: kconfig: don't select CPU_V7 per board
CPU_V7 is already selected by ARCH_MX6, so no point in selecting it again
by boards that depend on ARCH_MX6.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2015-08-02 10:51:38 +02:00
Nikita Kiryanov
81f5598b2d arm: mx6: cm-fx6: move cm-fx6 target under ARCH_MX6
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-08-02 10:51:38 +02:00
Peng Fan
8d7794615c imx: mx6qp Enable PRG clock for IPU
The i.MX6DQP has a PRG module, need to enable its clock for using IPU.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Brown Oliver <B37094@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-08-02 10:46:34 +02:00
Ye.Li
ec0f9530b1 imx: mx6: hab : Remove the cache issue workaroud in hab for i.MX6QP
Since the i.MX6QP has fixed the issue in boot ROM, so remove the workaround
for i.MX6QP.

Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-08-02 10:45:41 +02:00
Peng Fan
e1c2d68b39 imx: mx6: ccm: Change the clock settings for i.MX6QP
Since i.MX6QP changes some CCM registers, so modify the clocks settings to
follow the hardware changes.

In c files, use runtime check and discard #ifdef.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-08-02 10:43:45 +02:00
Peng Fan
d0acd99334 imx: add cpu type for i.MX6QP/DP
Add cpu type for i.MX6QP/DP.

This patch also fix is_mx6dqp(), since get_cpu_rev can return MXC_CPU_MX6QP
and MXC_CPU_MX6DP, we should use:
(is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)).

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-08-02 10:42:48 +02:00
Masahiro Yamada
b0c8f4a797 Kill unneeded #include <linux/kconfig.h>
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.

By the way, there are exceptions for the statement above; host
programs.  In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not.  So, some
files still include <linux/config.h> to work around build errors
on host tools.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-27 15:02:12 -04:00
Paul Kocialkowski
bafa6f591b am33xx: Unused get_board_rev function removal
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-07-27 15:02:10 -04:00
Paul Kocialkowski
fb9006c3a5 omap3: CONFIG_REVISION_TAG ifdef check for get_board_rev
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-07-27 15:02:10 -04:00
Paul Kocialkowski
d1a04b32f4 omap5: Definitions for SYS_BOOT-based fallback boot device selection
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:02:09 -04:00
Paul Kocialkowski
94fc751d8a omap4: Definitions for SYS_BOOT-based fallback boot device selection
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:02:08 -04:00
Paul Kocialkowski
cfac375616 omap3: Definitions for SYS_BOOT-based fallback boot device selection
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:02:07 -04:00
Paul Kocialkowski
ed19bdaea3 omap-common: SYS_BOOT-based fallback boot device selection for peripheral boot
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.

This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.

Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:02:06 -04:00
Paul Kocialkowski
df844772f7 omap-common: Boot device define instead of hardcoded value
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:02:05 -04:00
Paul Kocialkowski
60c7c30aa0 omap-common: Common boot code OMAP3 support and cleanup
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.

First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.

The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.

The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.

All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:02:03 -04:00
Tom Rini
26473945ad Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-07-25 09:04:18 -04:00
Hans de Goede
9ecce9707b sunxi: musb: Stop treating not having a vbus-det gpio as an error
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.

Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-07-25 11:22:55 +02:00
Hans de Goede
48c06c98ec sunxi: usb-phy: Add support for reading otg id pin value
Add support for reading the id pin value of the otg connector to the usb
phy code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-07-25 11:22:54 +02:00
Daniel Kochmański
a151403fd2 sunxi: spl: Detect at runtime where SPL was read from
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.

Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-24 16:17:08 +02:00
Paul Kocialkowski
17da3c0c8c usb: Fastboot function config for better consistency with other functions
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>

Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
2015-07-22 08:57:53 +02:00
Wang Dongsheng
340848b185 arm/ls102xa: Add PSCI support for ls102xa
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.

Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K

Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:38 -07:00