Add support of eMMC device boot partition with
part_id = -1 for offset="boot1"
or = -2 for offset="boot2"
The stm32prog command configures the MMC DFU backend with "mmcpart"
and configure the eMMC (command "mmc bootbus" and "mmc partconf")
when the update is done.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.
Create a GPT partitioning on the device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Build the list of device and of partition with
a tab separated value file with a stm32 header: the FlashLayout.tsv
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add prototype for function dfu_transaction_initiate and
dfu_transaction_cleanup to avoid warning with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function g_dnl_set_product to change the Product string used in USB
enumeration in any command based on download gadget.
If the function is called with NULL pointer, the product string is set to
the default value (product[] = "USB download gadget").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update stm32mp1 board documentation with new management of MMC and
MTD partitions and new PID df11.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from
NOR or NAND/SPI-NAND is detected.
This patch avoids to define the save MTD partition name for NOR and NAND
devices and issue with latest kernel: only the needed MTD partitions
are defined.
For boot from NOR
1/ bootloader (TF-A, U-Boot and OP-TE) in NOR
2/ one large UBI partition in NAND
For boot from NAND
1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition
2/ one large UBI partition
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save and use the FDT address provided by TF-A in r2 at boot time
(it is NT_FW_CONFIG = Non Trusted Firmware configuration file)
Address is saved in save_boot_params(), called by start.S
and the used DTB is gd->fdt_blob = board_fdt_blob_setup().
If dtb is not provided or invalid, U-Boot use as fallback
the builtin DTB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add support for multiple DRAM configuration subnodes, while retaining
the support for a single flat DRAM configuration node. This is useful
on systems which can be manufactured in multiple configurations and
where the DRAM configuration can be determined at runtime.
The code is augmented by a function which can be overridden on board
level, allowing a match on the configuration node name, very much like
the fitImage configuration node name matching works. The default match
is on the single top-level DRAM configuration, if matching on subnodes
is required, then this board_stm32mp1_ddr_config_name_match() must be
overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Add weak implementation of board_early_init_f() hook into the
STM32MP1 SPL. This can be used to read out e.g. configuration
straps before initializing the DRAM.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add default U-Boot configuration for the DHCOR SoM on AV96 board.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Here we improve clock support for recently introduced HSDK-4xD
board as well as finally enable external reset for the USB controller,
which is needed to recover USB functionality after "usb reset".
Add reset phandle to EHCI device tree node to make on-chip reset
controller usable with EHCI.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Anounce state of BIM switch which defines if U-boot is loaded
and started by preloader or not.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
HSDK and HSDK-4xD clock trees are slightly different.
commit 1dfb2ec0d7 ("ARC: HSDK: CGU: add support for timer clock")
introduce regression for HSDK board cause crash when setting
tunnel clock. Fix that.
Fixes: 1dfb2ec0d7 ("ARC: HSDK: CGU: add support for timer clock")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't want to allow change some clocks, i.e. DDR clock.
So allow to have set_clock to be unset in clock map.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The clock trees of HSDK and HSDK-4xD vary so we need to prepare
CGU driver for multiple clock maps support.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* constify clocks config data where is possible
* use more appropriate data types for clocks config
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Drop creg_div_oft offset as it doesn't vary (due to it is used for
CPU PLL only).
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
hsdk_axi_clk_cfg and hsdk_tun_clk_cfg clock divider structures
and functions for their processing are almost the same so
merge them to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Some systems may use a slightly larger stub to do PSCI for booting the RPi
family. The number of pages has been made configurable so that operating
systems building U-Boot for use in these kinds of environments can reserve
more memory in the EFI memory map.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
While the nearly-universal default for the Raspberry Pi family is to use
spin tables and the spin table implementation provided by the Raspberry Pi
Foundation, FreeBSD and others may use a PSCI implementation instead.
Accommodate these setups by allowing them to configure for more than one
page to be reserved in the initial reservation. The default reservation
remains as one page.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If CONFIG_MMC_SDHCI_SDMA is enabled but the HW could not support it,
we no longer error out. Instead we do not enable it in the host.
Change the output from printf to debug as this isn't an error but only
additional information now.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use the same environment size as the configs dedicated for rpi3 and rpi4.
This allows to switch between the builds and not to loose the settings
stored on the SD card.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If Host controller doesn't support SDMA, it doesn't need to return
error. Because it can be worked with PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use phys2bus macro when dma address is accessed.
Some targets need to use pyhs2bus macro. (e.g, RPI4)
After applied it, SDMA mode can be used.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We cannot rely on a parent bus that needs to be probed, until we know that
it is probed. That means that code in the ofdata_to_platdata() method
cannot rely on the parent bus being probed.
Move the ofdata code in the two serial drivers into a probe() method.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
At present the pinctrl nodes are not enabled in pre-relocation U-Boot so
the UARTs do not correctly select the pinconfig to enable the UART pins.
Fix this so that the U-Boot banner is printed.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 9821636b64 (bcm2835_pinctrl: Probe pre-reloc)
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As per Linux's driver, ID_MODE_DIS is only set when the PHY interface is
RGMII. Don't enable it for the rest of setups.
This has been seen to misconfigure RPi4's PHY when booting Linux.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Xilinx Versal platform uses dwc3 and hence its compatible string
needs to be added to dwc3 glue ids.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
