This patch fixes warnings like this:
start.S:0: warning: target CPU does not support interworking
which come from some ARM cross compilers and are caused by hard-coded
(with "--with-cpu=arm9" configuration option) ARM targets (which
support ARM Thumb instructions), while the ARM target selected from
the command line (with "-march=armv4") doesn't support Thumb
instructions.
This warning is issued by the compiler regardless of the real use of
the Thumb instructions in code.
To fix this problem, we use options according to compiler version
being used.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here
Add a warning in DDR1 case if cas_latency isn't a value we know about.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Adds returning an error from the ramdisk detection code if
its not a real ramdisk (invalid). There is no reason we can't
just return back to the console if we detect an invalid
ramdisk or CRC error.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds bootm_start() return value check. If
error status is returned, we do not proceed further to
prevent board reset or crash as we still can recover
at this point.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
I didn't try to use drivers/mtd/nand/fsl_upm.c for the NAND driver,
because I have no longer access to the hardware.
Signed-off-by: Heiko Schocher <hs@denx.de>
Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE.
When CONFIG_DISABLE_CONSOLE is defined, setting
GD_FLG_DISABLE_CONSOLE disables all console input and output.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>
This patch fixes a problem spotted on Glacier/Canyonlands (and most
likely lots of other board ports), that no serial output was seen
after console initialization in console_init_r(). This is because the
last added console device was used instead of the first added.
This patch fixes this problem by using list_add_tail() instead of
list_add() to register a device. This way the first added console
is used again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cleans up some latent issues with the data cache control so that
dcache_enable() and dcache_disable() will work reliably (after
unlock_ram_in_cache() has been called)
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Record the Arbiter Event Register values and optionally display them.
The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.
Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
#define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
and type register values
#define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter
event register values
Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
#define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
only events, so that it can still capture
other real problems.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.
Set gpio level register before direction register to inhibit
glitches on high level output pins.
Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.
Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds initdram() to DASA_SIM boards that has been
removed accidentally by a previous commit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some direct references to common/lists.o from some
esd linker scripts. This is necessary because the lists source was moved
and is not in the "common" directory anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes initdram() and testdram() from most esd 405 platforms.
Some boards also have an empty dummy implementation of
misc_init_f(). This is also removed.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removed the obsolete initdram() function from
VOM405 platform file.
Some minor cleanup.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the PCI-OHCI controller on PLU405 board.
Also the default CPU frequency is updated to 266 MHz and
command line editing is enabled.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch
- wraps some long lines
- removes unused/obsolete functions: misc_init_f() and initdram()
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
If a board has a variable number of flash banks, there are empty entries
in flash_info[] and CFG_DIRECT_FLASH_TFTP is set, tftp boot fails with
"Outside available Flash". This patch skips flash banks with unknown
flash ids.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
