There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.
The added dts file matches the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.
With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.
Signed-off-by: Pavel Machek <pavel@denx.de>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 USB gadget port
- 1 USB host port with an on-board hub
- 2 QSPI NORs connected to the Cadence QSPI core
- Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
---
V2: Update the defconfig as per Tom's request
P2771-0000 is a P3310 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B
port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO expansion
headers.
Currently, due to U-Boot's level of support for Tegra186, the only
features supported by U-Boot are the console UART and the on-board eMMC.
Additional features will be added over time.
U-Boot has so far been tested by replacing the kernel image on the device
with a U-Boot binary. It is anticipated that U-Boot will eventually
replace the CCPLEX bootloader binary, as on previous chips. This hasn't
yet been tested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add minimal dts support for AM335x-ICEv2 board
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Allow am335x-bone.dts to be built and enable uart and timer
for all beaglebones.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The originally committed .dts files for the Pine64 were from an early
proof-of-concept version and should have never been committed upstream.
Replace them with much more mature versions, which also use a different
naming scheme.
Please note that at this point there is at least one binding which has
not been agreed upon, so this is subject to change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.
This patch adds a defconfig and device tree chunks for it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
The added dts file is identical to the one submitted to the upstream
kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD,
A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at
i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and
rtl8188etv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.
The added dts is identical to the dts submitted to the upstream kernel,
note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the
upstream kernel as the added dts depends on these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Sync dts files with the upstream kernel including
changes queued for 4.6:
https://git.kernel.org/cgit/linux/kernel/git/mripard/linux.git/commit/?h=sunxi/dt-for-4.6
Note this adds a number of new unused board dts files. I've asked the
authors of the kernel commits adding these to submit a matching defconfig
to u-boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Convert ls1021aqds_nor_lpuart and ls1021aqds_ddr4_nor_lpuart
to driver model suport. Enable lpuart port driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Initial commit for PH1-Pro4 Ace and Sanji boards.
Note:
There are two variants for the Ace board in terms of the amount of
DDR memory; 1GB or 2GB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add device tree files for Phytec phyCORE-Vybrid Board.
- Enable lpuart support for Phytec phyCORE-Vybrid Board.
- Use UART1 for stdout.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add device tree files for NXP/Freescale VF610 Tower Board.
- Enable lpuart support on NXP/Freescale VF610 Tower Board.
- Use UART1 as stdout.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add lpuart support using the driver model.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move new /chosen node out of the board device tree.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert ls1021atwr_nor_lpuart to driver model support. As a start,
enable lpuart serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the FDT for the ThunderX family of SoCs
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is needed for the upcoming ethernet DM conversion of the maxbcm
board. The configuration of the PHY is then extracted from the DT
instead of using the defines from the config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add dts and defconfig for h8homletv2 board.
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.
A83T patches are tested on this board.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The SR1500 board is a CycloneV based board, similar to the EBV
SoCrates, equipped with the following devices:
- SPI NOR
- eMMC
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
This add some basic files required to allow the board to dispaly
serial message and can run command(mmc info etc)
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Moved board Kconfig fragment from previous patch into this one to fix
build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-changes: 8
- moved board Kconfig fragment from previous patch into this one
Reuse dts files from ls1043a linux kernel. Some parts in dts files
may not be needed by U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These files are based on the current latest upstream kernel work. The
bus_gates bindings may still change, but for u-boot that does not matter
as we do not (yet) use any clock info from devicetree for sunxi u-boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Import various DT files for am57xx-beagle-x15 from
Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO,
DM_SERIAL and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Import various DT files for am437x-sk-evm from Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO, DM_SERIAL
and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Import various DT files for am4372, an43xx pinctrl and
am437x-gp-evm from Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO, DM_SERIAL
and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Import various DT files for dra7-evm from Linux Kernel v4.2
Add config file for this board, enable DM and DM_GPIO
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These will be needed by the upcoming DM (driver model) support for
the Armada XP / 38x SoC's. This will provide DT based probing.
The dts files are copied 1:1 from the Linux kernel release v4.2.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
The DT is identical to the DT submitted to the upstream kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used
for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet
phy. ALDO1 is used to power the sdio wifi module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have generic q8_a?3_defconfig files for Q8 formfactor tablets with
an A13 / A23 / A33 SoC, there is no need for these PCB variant specific
defconfig-s and they only serve to confuse the user.
Note that in case of the forfun_q88db_defconfig and TZX-Q8-713B7_defconfig
for A13 based Q8 tablets there is not even a dts file for these in the
upstream kernel, which is all the more reason to remove them.
The generic q8_a?3_defconfig files have been tested on an Et_q8_v1_6,
Ippo_q8h_v1_2_a33_1024x600, Ippo_q8h_v1_2 and TZX-Q8-713B7 tablet, and the
forfun_q88db_defconfig is identical to q8_a13_tablet_defconfig.
This leaves only the Ippo_q8h_v5 untested with the new generic defconfigs
but there is no reason to assume that it will not work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts[i] files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
