Commit graph

5 commits

Author SHA1 Message Date
Ira W. Snyder
db1fc7d28e mpc8308rdb: add support for eSDHC MMC controller
Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:

- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>

[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-09-18 16:16:45 -05:00
Ira W. Snyder
ea1ea54e35 mpc8308rdb: add support for Spansion SPI flash on header J8
The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.

This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-09-18 16:16:44 -05:00
Peter Tyser
6aa3d3bfaa 83xx: Remove warmboot parameter from PCI init functions
This change lays the groundwork for the BOOTFLAG_* flags being removed.

This change has the small affect of delaying 100ms on PCI initialization
after a warm boot as opposed to the optimal 1ms on some boards.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

included the mpc8308_p1m board.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-09-23 21:14:42 +02:00
Ilya Yanok
65ea758939 MPC8308RDB: various clean ups
This patch cleans up the Freescale MPC8308RDB Development board support.
Things fixed:
 - Removed unused PCIE2 definitions from configuration
 - SICR{L,H} defines used for System I/O Configuration Registers values
   instead of hardcoding
 - CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of
   writing to SCCR from the board code
 - sleep mode stuff removed as MPC8308 has no support for deep sleep and
   PMCCR1 register. board_early_init_f() removed.
 - MPC8308 has no ERRATA for DDR controller so workaround removed
 - 'assignment in if statement' issues solved
 - use LBLAWAR_* defines instead of hardcoding

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-09-23 21:14:08 +02:00
Ilya Yanok
5fb17030d5 MPC8308RDB: minimal support for devboard from Freescale
This patch provides support for MPC8308RDB development board from
Freescale with a minimal set of features:
 Dual UART is supported
 NOR flash is supported
 Both TSEC Ethernet controllers are supported
 PCI Express initialization is supported

The following features are enabled in configuration but not fully tested:
 I2C (used to get the board revision)
 I2C-connected RTC
 VSC7385 switch

There is one (hopefully) minor issue: on soft reset the board sometimes
resets twice. I've not managed to find the fix for this problem yet.
As a workaround instruction cache can be disabled.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09 16:10:36 -05:00