Commit graph

53512 commits

Author SHA1 Message Date
Anatolij Gustschin
58ec4d3342 net: fec_mxc: add support for i.MX8X
Add compatible property and enable the FEC ipg clock when probing
on i.MX8X. Add specific function for reading FEC clock rate via
clock driver when configuring MII speed register. Allow FEC_MXC
selection for i.MX8.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:38 -05:00
Baruch Siach
18593fa80b net: mvpp2: increase PHY reset pulse
The default Linux PHY reset delay is 10ms. This is also the requirement
for Marvell 88E151x PHYs, which are likely to be used with this Ethernet
MAC.

Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-10-24 14:45:38 -05:00
Baruch Siach
fa14027d5c net: mvpp2: fix polarity of PHY reset signal
The dm_gpio_set_value() call sets the logical level of the GPIO signal.
That is, it takes the GPIO_ACTIVE_{LOW,HIGH} property into account. The
driver needs to assert the reset, and then deassert it. Not the other
way around.

Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-10-24 14:45:38 -05:00
Priyanka Jain
1ddcf5edbb net/phy: Add phy-id for IN112525_S03
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:38 -05:00
Martin Fuzzey
0126c641e8 net: dm: fec: Obtain the transceiver type from the DT
The DT property "phy-mode" already provides the transceiver type.
Use it so that we do not have to also set CONFIG_FEC_XCV_TYPE

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Martin Fuzzey
ad8c43cbca net: dm: fec: Support the phy-supply binding
Configure the phy regulator if defined by the "phy-supply" DT phandle.

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Martin Fuzzey
331fcabe4f net: dm: fec: Fix phy-reset-duration clamping and defaults
The DT binding says:
- phy-reset-duration : Reset duration in milliseconds.  Should present
  only if property "phy-reset-gpios" is available.  Missing the property
  will have the duration be 1 millisecond.  Numbers greater than 1000 are
  invalid and 1 millisecond will be used instead.

However the current code:
 - clamps values greater than 1000ms to 1000ms rather than 1.
 - does not initialize the delay if the property does not exist
   (else clause mismatch)
 - returns an error if phy-reset-gpios is not defined

Fix all this and simplify by using dev_read_u32_default()

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Martin Fuzzey
9b8b918884 net: dm: fec: Fix time unit error in phy-reset-duration
The DT binding says that phy-reset-duration is in ms, but the driver
currently uses udelay().

Switch to mdelay() to fix this.

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
30a2c8cca8 net: phy: aquantia: autodetect if firmware needs to be loaded
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware.  This allows the same image
to be used on boards that have firmware storage and those that do not.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
4506423ad2 net: phy: aquantia: add firmware loading support
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
1c6501088e configs: migrate CONFIG_PHY_AQUANTIA to Kconfig
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:36 -05:00
Pankaj Bansal
9215bb1f37 miiphy: Add function to retrieve MDIO bus list head
In upcoming freescale board LX2160AQDS, the MDIO bus is muxed.
i.e. same MDIO bus can be routed to eight different slots depending
on mux register settings.

To support this mdio mux behavior, we add each MDIO bus mux as a
separate MDIO bus.

Now, various phy devices can be attached to each of these slots(mux).
The information about these devices is passed to OS via device tree.

To do the fdt fixups related to MDIO bus, its necessary that MDIO bus
list is accessed.Therefore, add a function to retrieve the list head.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:36 -05:00
Hector Palacios
fb265a74cf cmd: mii: don't check address for 'device' subcommand
All mii operations require a valid PHY address except the 'device'
command, which expects the PHY name rather than the address.

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:36 -05:00
Priit Laes
3d99a0b33a sunxi: display: Mark sunxi_rgb2yuv_coef array as const
sunxi_rgb2yuv_coef is readonly and never modified.

Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Priit Laes
df4ad94d05 sunxi: docs: Mention CONFIG_NAND requirement
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Priit Laes
297963f5b5 sunxi: Fix typos of spelling Allwinner
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Vasily Khoruzhick
c33ba7ec8b pwm: sunxi: choose best prescaler to improve PWM resolution
Choose best prescaler to improve PWM resolution. Without this change
driver chooses first prescaler that gives us period value within
range, but it could be not the best one.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 21:57:16 +05:30
Vasily Khoruzhick
ce138cb429 pwm: sunxi: use new prescaler when configuring PWM
Looks like old prescaler was used when configuring PWM, fix it.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 21:57:05 +05:30
Vasily Khoruzhick
a877d4b1ae pwm: sunxi: fix off-by-one that prevented PWM to use prescaler bypass
Fix off-by-one that prevented PWM driver to use prescaler bypass.
Without this change prescaler is always enabled.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 21:56:57 +05:30
Fabio Estevam
bb839ad931 warp7: MAINTAINERS: Add an entry for warp7_bl33_defconfig
Add an entry for the warp7_bl33_defconfig target.

This fixes the following warnings:

WARNING: no status info for 'warp7_bl33'
WARNING: no maintainers for 'warp7_bl33'

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
2018-10-24 10:03:06 +02:00
Tom Rini
1ed3c0954b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2018-10-23 21:13:32 -04:00
Tom Rini
818408e203 travis: Rework Freescale ARM jobs a bit
- Split the AArch64 LS10xx and LS20xx builds into their own jobs, and
  then exclude only ls1/ls2 from the catch-all.  This moves the S32V234
  job (and future i.MX8*) to the catch-all.
- Split spear out from arm926ejs and exclude freescale, not mx from that
  job.  The older Freescale i.MX boards are caught by the catch-all job
  for Freescale but now we build the non-Freescale older i.MX platforms.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-23 11:58:44 -04:00
Dirk Meul
9cd97c5b04 ARM: Samsung: Add Exynos5422-based Odroid HC2 support
Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1.

The linux kernel does not provide a hc2 DTB so the hc1 DTB is also used
for the Odroid HC2.

Resend because MUA changed whitespace.

Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2018-10-23 20:00:52 +09:00
Simon Glass
3ae192c2a4 binman: Add a test for Intel reference code
Unfortunately the test was not included in the original implementation.
Add one.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-22 13:57:12 -04:00
Tom Rini
c95c666d01 Merge git://git.denx.de/u-boot-x86 2018-10-22 13:56:10 -04:00
Bernhard Messerklinger
4684fa8bdd serial: mxc: Add match string for i.mx6 quad/dual lite serial
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2018-10-22 18:56:17 +02:00
Sam Protsenko
88d60db011 arm: ti: boot: Remove environment partition
Remove "environment" partition and do not read it when booting Android
from eMMC. We don't use this partition anymore, so this is just an
unintentional leftover.

Earlier we were reading dtb file from "environment" partition to feed it
further to kernel. Now we are using dtb from FIT image ("boot" partition
contains boot_fit.img image), which can be seen from this command:

    bootm ${loadaddr}#${fdtfile}

where "#" character means we have FIT image in ${loadaddr} RAM address.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
2018-10-22 09:18:49 -04:00
Cédric Le Goater
e1a8dfde5a watchdog: aspeed: restore default value of reset_mask
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-22 09:18:49 -04:00
Adam Ford
290097fe27 ARM: omap3_logic: Add NOR Flash Support for SOM-LV
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Meul, Dirk
e18333e501 arm: udoo: Convert to distro config
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.

Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2018-10-22 09:18:49 -04:00
Heinrich Schuchardt
d796735c33 test: overlay: add missing include
Compiling the overlay unit test fails with odroid-c2_defconfig showing
errors like:

    test/overlay/cmd_ut_overlay.c:29:8:
    error: unknown type name ‘fdt32_t’

Add the missing include.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-22 09:18:49 -04:00
Bin Meng
ed5df0852f nand: atmel: Initialize pmecc smu with correct size
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.

In fact, GCC 8.1.0 reports a warning against it:

error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]

Fix it by using the correct size.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
7702713ee8 configs: sama5d2_ptc_ek: add default bootargs for MMC defconfig
Add default bootargs for the MMC defconfig to use SD-Card as rootfs

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
3fbf61a770 configs: sama5d2_ptc_ek: add default bootargs for NAND defconfig
Add the default kernel bootargs according to our NAND flash demo layout:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d2PtcEKMainPage#NAND_Flash_demo_Memory_map

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
76892d0115 configs: sama5d2_xplained: enable w1 and overlay for emmc defconfig
Enable onewire support and commands, fdt overlay for the emmc defconfig.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
ac5c1f0f3e configs: sama5d27_som1_ek: enable w1 and overlay for mmc1 defconfig
Enable onewire support and commands, fdt overlay for the mmc1 defconfig.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
367386861b configs: at91: sama5: enable CMD_IMI
Enable iminfo command with CONFIG_CMD_IMI

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
96ab34b484 configs: at91: sam9x5: added FIT and iminfo support
Enabled FIT image support and iminfo command for FIT information.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Eugen Hristev
61b4dbb0d0 board: at91sam9x5: add environment var for cpu type
When booting and CPU is detected from cpuid, we also need an environment
variable that will be used in boot commands to load the proper devicetree.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-22 09:18:49 -04:00
Adam Ford
6482095de6 ARM: omap3logic: Fix MMC name
In my haste to migrate SPL to DM, I copied the wrong name.
While it really doesn't matter, I'd prefer the name to match
the board, so am335x_mmc0 is now called omap3_logic_mmc0

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Adam Ford
c3aa851322 ARM: omap3logic: Specify DM serial driver as omap_serial
With the new omap_serial driver, this patch uses this instead
from the former ns16550_serial driver.  Even though the
omap_serial driver is essentially the same.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Adam Ford
f4db3b68c1 ARM: omap3logic: Encapsulate the MUSB functions in check for DM
With the DM_USB working for USB host features, encapsulate the
USB gadget initialization in a precomiler check.  If DM is enabled,
we don't need to manually initialize the MUSB driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Adam Ford
169eb19135 ARM: omap3_logic.c: Optimize DDR timings based on OMAP35 or 36/37
The default timings are assumming an OMAP36 / AM37 / DM37, but
the OMAP35 controller is a bit slower, so DDR may operate out of
spec when under stress.  This patch checks the processor type and
sets the DDR timings according to processor type.

Fixes: 5ad4212ce0 ("ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV
and OMAP35 Torpedo")

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Adam Ford
017d9819e4 ARM: da850evm_direct_nor: Remove DM_I2C_COMPAT
The da850evm does not need this enabled, so this removes a
notice that appears during compile time that says
"Please remove"

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Rui Miguel Silva
e292e1d9df warp7: configs: add bl33 defconfig
Add default configuration to run u-boot as BL33 in the ARM Trusted Firmware
boot flow for AArch32 case.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: u-boot@lists.denx.de
2018-10-22 14:37:28 +02:00
Rui Miguel Silva
a612e25e13 warp7: include: configs: set skip low level init
If we have defined the OPTEE ram size and not OPTEE means that we are in
the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and
that most of the low level initialization is already done and that we
may/should skip it doing them here.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: u-boot@lists.denx.de
2018-10-22 14:37:28 +02:00
Rui Miguel Silva
c7b3a7ee53 optee: adjust dependencies and default values for dram
We may have, the not yet considered, scenario where OPTEE is loaded before
u-boot and *not* by u-boot, e.g, the boot flow using the ARM Trusted
Firmware (ATF), where in the 32bit flow is:
BootRom->ATF(BL2)->Optee(BL32)->u-boot(BL33)

In this case we need still to reserve the memory used by optee, to avoid
for example to realocate ourself to the same address at the end of DRAM.
So, we change here the dependencies on the OPTEE lib and we set the default
size and base of TZRAM to zero.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: u-boot@lists.denx.de
2018-10-22 14:37:28 +02:00
Rui Miguel Silva
be277c3a89 imx: mx7: avoid some initialization if low level is skipped
We can have the case where u-boot is launched after some other low level
enabler, like for example when u-boot runs after arm-trusted-firmware
and/or optee. So, because of that we may need to jump the initialization of
some IP blocks even because we may no longer have the permission for that.

So, if the config option to skip low level init is set disable also timer,
board and csu initialization.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: u-boot@lists.denx.de
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2018-10-22 14:37:28 +02:00
Anatolij Gustschin
7677c0de14 i2c: imx_lpi2c: fix typo and register base address format
Output the register base address in hex notation.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2018-10-22 14:35:57 +02:00
Xiaoliang Yang
517066a709 Kconfig: Convert CONFIG_IMX_WATCHDOG to Kconfig
Move this option to Kconfig and tidy up the config file of eight
boards which use it.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
2018-10-22 14:33:54 +02:00