As we are not reading the PHY address in case of CONFIG_ETH_PHY in plat
function, phy address always prints as -1. So move the ethernet info
print statement to probe function, to display proper phy address.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f6efc6719d767b1bebe65987c22c6d52329f4225.1648631275.git.michal.simek@xilinx.com
For configurations with gmii2rgmii and external phy the DT nodes link
should be gem->gmii2rgmii->phy. But due to limitation in Linux driver
the DT is mentioned as gem->phy and gmii2rgmii->phy as shown in below DT.
ethernet@ff0c0000 {
compatible = "cdns,zynqmp-gem\0cdns,gem";
status = "okay";
interrupt-parent = <0x04>;
interrupts = <0x00 0x3b 0x04 0x00 0x3b 0x04>;
reg = <0x00 0xff0c0000 0x00 0x1000>;
clock-names = "pclk\0hclk\0tx_clk\0rx_clk\0tsu_clk";
#address-cells = <0x01>;
#size-cells = <0x00>;
#stream-id-cells = <0x01>;
iommus = <0x0d 0x875>;
power-domains = <0x0c 0x1e>;
clocks = <0x03 0x1f 0x03 0x69 0x03 0x2e 0x03 0x32 0x03 0x2c>;
phy-handle = <0x0e>;
phy-mode = "gmii";
xlnx,ptp-enet-clock = <0x00>;
local-mac-address = [ff ff ff ff ff ff];
phandle = <0x4d>;
mdio {
#address-cells = <0x01>;
#size-cells = <0x00>;
phandle = <0x4e>;
ethernet-phy@1 {
reg = <0x01>;
rxc-skew-ps = <0x708>;
txc-skew-ps = <0x708>;
phandle = <0x0e>;
};
gmii_to_rgmii_0@8 {
compatible = "xlnx,gmii-to-rgmii-1.0";
phy-handle = <0x0e>;
reg = <0x08>;
phandle = <0x4f>;
};
};
};
Since same DT is used in Linux and U-Boot we need to workaround this
issue by using the gmii2rgmii node which points to phy and we should
ignore the gem pointing to phy directly.
Do this workaround by updating priv->phydev->node value with
priv->phy_of_node only if it is not valid node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/641eb13425ffe80e0743f60cf90d0f940577b9e9.1642162085.git.michal.simek@xilinx.com
Perform reset before core initialization.
Standard flow which close to 99% users are using getting all IPs out of
reset that there is no need to reset IP again. This is because of all low
level initialization is done in previous bootloader stage.
In SOM case these IPs are not touched by previous bootloader stage that's
why reset needs to be called before IP is accessed to make sure that it is
in correct state.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/5ae1c85b282d632bb62030f1f24a0065661b9153.1638804318.git.michal.simek@xilinx.com
Xilinx DTS files are using two way how to describe ethernet phy.
The first (already supported) has phy as subnode of gem node.
eth {
phy-handle = <&phy0>;
phy0: ethernet-phy@21 {
...
};
};
The second has mdio subnode (with mdio name) which has phy subnode. This
structure allow hadling MDIO reset signal (based on Linux mdio.yaml)
eth {
phy-handle = <&phy0>;
mdio {
phy0: ethernet-phy@21 {
...
};
};
};
This patch adds support for the second case where mdio subnode
is found driver will look at its parent to find out which gem is handling
MDIO bus.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6748007f0b6db9554d7a4b52352dce23ca403f9d.1638798796.git.michal.simek@xilinx.com
The code was trying to disable PCS auto-negotiation when a fixed-link node
is present and enable it otherwise. However, the PCS registers were being
written before the PCSSEL bit was set in the network configuration
register, and it appears that in this state, PCS register writes are
ignored. The result is that the intended change only took effect on the
second network operation that was performed, since at that time PCSSEL is
already enabled.
Fix the order of register writes so that PCS registers are only written to
after the PCS is enabled.
Fixes: 26e62cc971 ("net: gem: Disable PCS autonegotiation in case of fixed-link")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If probe fails, the mdio bus isn't unregistered. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Find out MDIO bus and enable MDIO access to it if this is done via
different GEM controller. Only works across GEM instances.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Disable PCS autonegotiation if fixed-link node is present in device tree.
This way systems with multiple GEM instances with a combination of
SGMII-fixed and SGMII-PHY will work.
Reported-by: Goran Marinkovic <goran.marinkovic@psi.ch>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all IPs have private MDIO bus and MDIO bus should be shared between
several IPs. In past one patch tried to implement it
(https://lists.denx.de/pipermail/u-boot/2018-February/319285.html)
in pretty raw way but it is not the cleanest solution.
This patch is just taking the part of that solution to be able to handle it
over releases without conflicts.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add cache flush to zynq_gem_free_pkt. This is necessary
because some net routines would modify this buffer in place.
The cache_invalidate in the zynq_gem_recv function would cause
the modifications to the buffer to overwrite the DMA from the GEM,
if cache coherency is not enabled in the GEM, the next time the
buffer is in use.
Flushing the cache when the buffer is no longer in use by the
net functions ensures that the GEM DMA is going to take place
into a clean buffer.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Driver probe function is called again and again in case of error.
Malloc space is getting full which is is reported by:
Insufficient RAM for page table: 0x15000 > 0x14000.
Please increase the size in get_page_table_size()
### ERROR ### Please RESET the board ###
The patch is freeing allocated buffers on error path to avoid panic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
flush_dcache_range() expects unsigned long in the arguments. Here u32
variable is unable to hold the higher address value when ddr mapped
to higher addresses & flushing lower address dchache range instead
which is unmapped causing to crash.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch removes check for Versal platform
in gem driver as it now supports clock setting
through clock framework.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new versal compatible string to GEM driver for Versal
platform.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The phydev supported features were reset in phy_set_supported() so,
move the setting of driver supported features after this so that it
wont lost in phy_set_supported().
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The cache was only flushed before *transmitting* packets, but not
when receiving them, leading to an issue where new packets were
handed to the receive handler with old contents in cache. This
only happens when a lot of packets are received without sending
packages every now and then. Also flushing the receive buffers
in the transmit function makes no sense and can be removed.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch throws an error if 64-bit support is expected
but DMA hardware is not capable of 64-bit support. It also
prints a debug message if DMA is capable of 64-bit but not
using it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch adds 64-bit addressing support for zynq gem.
This means it can perform send and receive operations on
64-bit address buffers.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Xilinx SoC Versal is using fixed clock where setting rate is not supported.
That's why workaround the driver till real clock driver is supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Based on dt-specs fixed-link doesn't require phy-handle to be used.
Fix driver to only read phy related setting when phy-handle is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
max-speed property is part of phynode and it has to be
read using ofnode_read_u32_default(). This fixes the issue
of incorrect max-speed read from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the zynq gem driver to support livetree.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now zynq_gem driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
phyread can timeout and val will contain random value. Initialize it to
zero not to report random value in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Functions can return NULL in case of error that's why checking return
value is needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In case of phyread()/phy_setup_op() timeout code is working with
uninitialized phyreg variable. Initialize this variable to make sure
that code it not working with random value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit_le32 returns negative value on failure. Fix phy...() to
handle these failures properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
