There are use cases where lpd watchdog can be configured for APU use. By
design this IP should be listed in zynqmp.dtsi to make sure that node is
properly enabled by DTG.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the nand device tree node properties as per
updated driver.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The following patch adds a mailbox node and firmware node to following the
mainline DT.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Mainline Linux kernel has adopted SPDX header license in a different
format then was used before. This patch is syncing it up.
Also update years in License text and remove Nathalie's email because it
is no longer valid.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync pcie and lpd_dma nodes with mainline version.
Incorrect locations are causing diff in statistics that's why
synchronizations are needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling support for SPL QSPI boot.
First of all it is necessary to generate atf-spi.ub which is different
format than atf-uboot.ub (this can be made as legacy image too)
ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point
address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'`
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR
-e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin
atf-uboot.ub
./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR
-n "atf-for-qspi" -E -d bl31.bin atf-spi.ub
This patch is using this QSPI layout with offsets:
0 boot.bin
512k atf-ub
640k u-boot.bin
1280k u-boot.img
Which corresponding by writing these images(read from MMC)
mmcinfo
sf probe
load mmc 0 10000000 boot.bin
sf erase 0 +$filesize
sf write 10000000 0 $filesize
load mmc 0 10000000 atf-spi.ub
sf erase 0x80000 +$filesize
sf write 10000000 0x80000 $filesize
load mmc 0 10000000 u-boot.bin
sf erase 0xa0000 +$filesize
sf write 10000000 0xa0000 $filesize
load mmc 0 10000000 u-boot.img
sf erase 0x140000 +$filesize
sf write 10000000 0x140000 $filesize
For testing u-boot running in EL3 you can break atf-spi.ub like this:
sf probe
sf erase 0x80000 +4
Then u-boot.img is executed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reference is needed for pinctrl driver where some signals can be
routed directly to platform management unit (PMU).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes SMMU work by moving the iommus node under the dwc3 child
entry from parent node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch uncomments snps,quirk-frame-length-adjustment which has
the value to adjust the SOF/ITP generated from the controller.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds OTG interrupt support in device tree. It will add
an extra interrupt line number dedicated to OTG events. This will
enable OTG interrupts to serve in DWC3 OTG driver.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds CCI support for USB when CCI is enabled in design.
This patch also adds 'reg' property for Xilinx USB 3.0 IP. The 'reg'
property is added in order to modify a register in that to enable
coherency in Hardware.
Also add address to unit name to avoid dtc warning
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for reading silicon revision using zynqmp nvmem
driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such as
temperature and supply voltage levels.
Signed-off-by: Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch sets host quirk2 bit field for No 1.8V supported in case of
1.0 silicon. The 1.0 silicon doesn't have support for UHS-I modes. This
property will ensure the SD runs on High Speed mode.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the phy_zynqmp.c driver to use reset-controller
framework for asserting/de-asserting reset for High Speed modules.
Also fix documentation and dtsi.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add the reset nodes in zynqmp.dtsi which are used by
reset-controller framework
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Only silicon v1 requires this termination fix. With new nvmem soc
revision nvmem detection driver this can be autodetected at run time and
this flag is not needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for zynqmp nvmem firmware driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added pin control support in device tree for zynqmp.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently DP power domain (pd_dp) is not attached to any of the DP nodes which is
causing genpd to trigger a power down request for DP domain, making all DP related
peripherals unusable. So assign power domains for all DP related nodes to enable
proper accounting of DP power domain usage.
Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch disables the smmu and also removes the mmu-masters
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the calibration property with required value,
calculated based on rtc input crystal oscillator frequency (32.768Khz).
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below
SATA SMMU ID = <TBU number>, 0011, 00, 00, AXI ID[1:0]
Note: SATA in ZynqMp uses TBU1 so TBU number = 0x1, so
SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]
Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values
Read ID/ Write ID for Non-Data Port0 transfers = 0
Read ID/ Write ID for Data Port0 transfers = 1
Read ID/ Write ID for Non-Data Port1 transfers = 2
Read ID/ Write ID for Data Port1 transfers = 3
Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All gpio controllers should contain this property.
This property is not checked by the code that's why this issue wasn't
found earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The correct register size is 0x10000, otherwise
it overlaps with other register space.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch will add names to the clocks used by GPU.
Signed-off-by: Madhurkiran Harikrishnan <madhurki@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This will simplify dt overlay structure for the whole PL.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extract from Linux mainline patch:
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PM callbacks are delivered to the NS OS. Let the PM driver handle the
IRQ and retrieve callback data from the secure HW.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed min-residence to 10ms(was 100 ms) for cpu-sleep-0.
Tried lower values 5ms and 8ms and it worked fine with Debug Off.
But to accommodate PM Debug On case, 10 ms is required. With this
change, low power idle state is into effect more frequently.
Measured boot time with PM debugs On and Off. No change observed
compared to 100ms value.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>
Tested-by: Koteswararao Nayudu <kotin@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0
idle state is added in this patch. References to the idle-states node are
added in all CPU nodes. Time values: entry/exit latencies and min-residency,
needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0
and Extended StateID format.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
For LPDDMA channels the two clocks are missing in the
Dma node resulting probe failure.
xilinx-zynqmp-dma ffa80000.dma: main clock not found.
xilinx-zynqmp-dma ffa80000.dma: Probing channel failed
xilinx-zynqmp-dma: probe of ffa80000.dma failed with error -2
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
