Commit graph

126 commits

Author SHA1 Message Date
York Sun
ca1b0b8956 powerpc/P2041RDB: Fix Flash address LAW address
P2041RDB uses common corenet TLB and LAW. However it doesn't have promjet
connector. It is necessary to use the same base address for correct LAW
address. An offset is added for NOR flash.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:06 -06:00
York Sun
021382cad2 powerpc/qoriq: Move FMAN microcode location
Move FMAN microcude from 0xEF000000 to 0xEFF40000 to free up the beginning
of this virtual bank so that this bank can store RCW or be used together
with other banks to store large images.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:25:55 -06:00
Marek Vasut
5368c55d4c COMMON: Use __stringify() instead of MK_STR()
Kill multiple occurances and redeclaration of MK_STR
in favor of __stringify().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:47 -07:00
Scott Wood
3e978f5dc8 powerpc/fsl-corenet: remove dead variant symbols
These are not supported as individual build targets, but instead
are supported by another target.

The dead p4040 defines in particular had bitrotted significantly.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Liu Gang
461632bd71 powerpc/corenet_ds: Slave module for boot from PCIE
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.

Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.

NOTE: Because the slave can not erase, write master's NOR flash by
	  PCIE interface, so it can not modify the ENV parameters stored
	  in master's NOR flash using "saveenv" or other commands.

environment and requirement:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image is in master NOR flash.
	3. Put the slave's ucode and ENV into it's own memory space.
	4. Normally boot from local NOR flash.
	5. Configure PCIE system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to one PCIE interface by RCW.
	3. RCW should configure the SerDes, PCIE interfaces correctly.
	4. Must set all the cores in holdoff by RCW.
	5. Must be powered on before master's boot.

For the slave module, need to finish these processes:
	1. Set the boot location to one PCIE interface by RCW.
    2. Set a specific TLB entry for the boot process.
	3. Set a LAW entry with the TargetID of one PCIE for the boot.
	4. Set a specific TLB entry in order to fetch ucode and ENV from
	   master.
	5. Set a LAW entry with the TargetID one of the PCIE ports for
	   ucode and ENV.
	6. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIO_PCIE_BOOT_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
	1. Updated the README.srio-boot-corenet to add descriptions about
	   boot from PCIE, and change the name to
	   README.srio-pcie-boot-corenet.
	2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
	   "xxxx_SRIO_PCIE_BOOT", and the image builded with
	   "xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
	   from PCIE.
	3. Updated other macros and documents if needed to add information
	   about boot from PCIE.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:15 -05:00
Liu Gang
b5f7c8732a powerpc/corenet_ds: Master module for boot from PCIE
For the powerpc processors with PCIE interface, boot location can be
configured from one PCIE interface by RCW. The processor booting from PCIE
can do without flash for u-boot image. The image can be fetched from another
processor's memory space by PCIE link connected between them.

The processor booting from PCIE is slave, the processor booting from normal
flash memory space is master, and it can help slave to boot from master's
memory space.

When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.

Environment and requirement:

master:
    1. NOR flash for its own u-boot image, ucode and ENV space.
    2. Slave's u-boot image is in master NOR flash.
    3. Normally boot from local NOR flash.
    4. Configure PCIE system if needed.
slave:
    1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
    2. Boot location should be set to one PCIE interface by RCW.
    3. RCW should configure the SerDes, PCIE interfaces correctly.
	4. Must set all the cores in holdoff by RCW.
	5. Must be powered on before master's boot.

For the master module, need to finish these processes:
    1. Initialize the PCIE port and address space.
    2. Set inbound PCIE windows covered slave's u-boot image stored in
       master's NOR flash.
	3. Set outbound windows in order to configure slave's registers
	   for the core's releasing.
    4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2"
	   or "PCIE3" using the following command:

			setenv bootmaster PCIE1
			saveenv

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:15 -05:00
Liu Gang
81fa73bab0 powerpc/corenet_ds: Get rid of the CONFIG_SRIOBOOT_SLAVE_PORTx macro
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.

This has the following advantages:
	1. No longer need to rebuild an image when change the SRIO port for
	   boot from SRIO, just rewrite the new RCW with selected port,
	   then the code will get the port information by reading new RCW.
	2. It will be easier to support other boot location options, for
	   example, boot from PCIE.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:14 -05:00
Liu Gang
ff65f12699 powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build target
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:

		setenv bootmaster SRIO1
		saveenv

The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
	1. Reduce a build configuration item in boards.cfg file.
	   No longer need to build a special image for master, just use a
	   normal target image and set the "bootmaster" variable.
	2. No longer need to rebuild an image when change the SRIO port for
	   boot from SRIO, just set the corresponding value to "bootmaster"
	   based on the using SRIO port.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:14 -05:00
Shaohui Xie
0f57f6a3fe powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
ENV location compile logic is wrong, and when CONFIG_SYS_NO_FLASH is defined
and non-NOR u-boot is building, it will cause compile error. Also, add
CONFIG_SYS_FLASH_USE_BUFFER_WRITE for p2041, which will improve NOR flash
write performance.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:38 -05:00
ramneek mehresh
3d7506fa38 powerpc/85xx: Add USB device-tree fixup for various platforms
Add USB device-tree fixup for following platforms:
MPC8536DS, P1022DS, P1023RDS, P2020COME, P2020DS, P2041RDB, P3060QDS

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2012-07-06 17:03:25 -05:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Shaohui Xie
15c8c6c20c powerpc/p2041rdb: add env in NAND support
Add env in NAND support when boot from NAND.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:31 -05:00
Shaohui Xie
c9b2feafaa powerpc/p2041rdb: add NAND and NAND boot support
New P2041RDB board will add a NAND chip, so add support for NAND and
NAND boot.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:31 -05:00
Fabio Estevam
4394d0c2ee sdhc_boot: Introduce CONFIG_FSL_FIXED_MMC_LOCATION option
Since commit 97039ab98 (env_mmc: Allow board code to override the environment address)
mmc_get_env_addr is a weak-aliased function in common/env_mmc.c

The mmc_get_env_addr implementation that exists at
board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards,
but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined.

Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use
the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate
this config option on their board file.

This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:25 +01:00
Timur Tabi
f2717b47ea powerpc/85xx: clean up and document the QE/FMAN microcode macros
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman.  Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both.  A given SOC will only have
a QE or an Fman, so this is safe.

Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND.  There's no way to know by looking at a variable how it's supposed
to be used.

In the future, the code which uploads QE firmware and Fman firmware will
be merged.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
3e0529f742 powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files.  So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020.  It was already defined for the
P1010 and P1014.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Joe Hershberger
b3f44c21ea common: cosmetic: CONFIG_BOOTFILE checkpatch compliance
Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:21:35 +02:00
Joe Hershberger
8b3637c662 common: cosmetic: CONFIG_ROOTPATH checkpatch compliance
Remove MK_STR from places that consume CONFIG_ROOTPATH to force all definitions to be string literals.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:21:15 +02:00
Kumar Gala
4d28db8a1e powerpc/85xx: Add support for RMan LIODN initialization
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:48 -05:00
Mike Frysinger
31a4f1e5b6 board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Shaohui Xie
44d50f0b54 powerpc/p2041rdb: set sysclk according to status of physical switch SW1
P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8],
software need to read the SW1 status to decide what the sysclk needs.

SW1[8~6] : frequency
0 0 1 : 83.3MHz
0 1 0 : 100MHz
others: 66.667MHz

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:30:02 -05:00
Mingkai Hu
0787ecc01f powerpc/p2041rdb: Add ethernet support on P2041RDB board
Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.

The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Timur Tabi
e46fedfeb2 powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot).  All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Mingkai Hu
aa7f281ce4 powerpc/p2041rdb: Enable SATA support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Mingkai Hu
cd420e0b2a powerpc/p2041rdb: Enable backside L2 cache support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Mingkai Hu
4f1d1b7d1e powerpc/p2041rdb: Add p2041rdb board support
P2041RDB Specification:
-----------------------
Memory subsystem:
 * 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 256 Kbit M24256 I2C EEPROM
 * 16 Mbyte SPI memory
 * SD connector to interface with the SD memory card

Ethernet:
 * dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
 * dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)

PCIe:
 * Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 * Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2

SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors

USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces

I2C:
 * I2C1: Real time clock, Temperature sensor, Memory module
 * I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-17 11:03:36 -05:00