This patch add basic support for the architecture timer found on recent
ARMv7 based SoCs.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.
Signed-off-by: Nishanth Menon <nm@ti.com>
introduce get_die_id() function which allows generation of
information such as fake MAC address from the processor ID code.
Signed-off-by: Nishanth Menon <nm@ti.com>
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.
Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.
NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.
Signed-off-by: Nishanth Menon <nm@ti.com>
Replace the custom bit manipulation function sr32() by standard I/O
accessors. A major motivation for this cleanup was the fact, that a
number of calls of that function resulted in 32 bit wide shift
operations on u32 data, which according to the C-ISO/IEC-9899-Standard
provokes undefined behaviour:
6.5.7 Bitwise shift operators
...
If the value of the right operand is negative or is greater
than or equal to the width of the promoted left operand, the
behavior is undefined.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so make it a static function in
that file to prepare complete removal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch add gicv3 support to uboot armv8 platform.
Changes for v2:
- rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
- move smp_kick_all_cpus() from gic.S to start.S, it would be
implementation dependent.
- Each core initialize it's own ReDistributor instead of master
initializeing all ReDistributors. This is advised by arnab.basu
<arnab.basu@freescale.com>.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
When flush the d$ with set/way instruction, it need calculate the way's
offset = log2(Associativity); but in current uboot's code, it use below
formula to calculate the offset: log2(Associativity * 2 - 1), so finally
it cannot flush data cache properly.
Signed-off-by: Leo Yan <leoy@marvell.com>
For ARMv8, U-boot has been running at EL3 with cache and MMU enabled.
Without proper setup for EL2, cache and MMU are both disabled (out of
reset). Before switching, we need to flush the dcache to make sure the
data is in the main memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: David.Feng <fenghua@phytium.com.cn>
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
The anadig_reg structure started at the wrong offset (fixed by adding
reserved_0x000[4]), was missing some reserved field required for
alignment purpose (reserved_0x094[3] between pll4_denom and pll6_ctrl)
and further contained a too short reserved field causing further miss-
alignment (reserved_0x0C4[7]). Also, rename all the reserved fields
and using a memory offset based scheme for.
Discovered and tested by temporarily putting the following debug
instrumentation into board_init():
struct anadig_reg *anadig = (struct anadig_reg *)ANADIG_BASE_ADDR;
printf("&anadig->pll3_ctrl=0x%p\n", &anadig->pll3_ctrl);
printf("&anadig->pll5_ctrl=0x%p\n", &anadig->pll5_ctrl);
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
After Kbuild introduction, the CROSS_COMPILE environment variable has been
set to some default value (prefix arm-linux-).
This shall be removed since it breaks building u-boot for native arm target
(like qemu ARM).
Moreover not all compilers have arm-linux- prefix.
Additionally the u-boot cross compiles with CROSS_COMPILE= set explicitly-
e.g.:
CROSS_COMPILE=/ .... /arm-v7a-linux-gnueabi- make
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Full cache line writes to the same memory region from at least two
processors might deadlock the processor. Exists on r1, r2, r3
revisions.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
A short loop including a DMB instruction might cause a denial of
service on another processor which executes a CP15 broadcast operation.
Exists on r1, r2, r3, r4 revisions.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
When SoC first boots up, we should invalidate the cache but not flush it.
We can use the same function for invalid and flush mostly, with a wrapper.
Invalidating large cache can ben slow on emulator, so we postpone doing
so until I-cache is enabled, and before enabling D-cache.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
If D-cache is enabled, we need to flush it, and invalidate i-cache before
jumping to the new location. This should be done right after relocation.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
Move setting for MAIR and TCR to cache_v8.c, to avoid conflict with
sub-architecture.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
This patch adds the groundwork for generating signed BootStream, which
can be used by the HAB library in i.MX28. We are adding a new target,
u-boot-signed.sb , since the process for generating regular non-signed
BootStream is much easier. Moreover, the signed bootstream depends on
external _proprietary_ _binary-only_ tool from Freescale called 'cst',
which is available only under NDA.
To make things even uglier, the CST or HAB mandates a kind-of circular
dependency. The problem is, unlike the regular IVT, which is generated
by mxsimage, the IVT for signed boot must be generated by hand here due
to special demands of the CST. The U-Boot binary (or SPL binary) and IVT
are then signed by the CST as a one block. But here is the problem. The
size of the entire image (U-Boot, IVT, CST blocks) must be appended at
the end of IVT. But the size of the entire image is not known until the
CST has finished signing the U-Boot and IVT. We solve this by expecting
the CST block to be always 3904B (which it is in case two files, U-Boot
and the hand-made IVT, are signed in the CST block).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add support for serial console into the i.MX23/i.MX28 SPL. A full,
uncrippled serial console support comes very helpful when debugging
various spectacular hardware bringup issues early in the process.
Because we do not use SPL framework, but have our own minimalistic
SPL, which is compatible with the i.MX23/i.MX28 BootROM, we do not
use preloader_console_init(), but instead use a similar function to
start the console. Nonetheless, to avoid blowing up the size of the
SPL binary, this support is enabled only if CONFIG_SPL_SERIAL_SUPPORT
is defined, which is disabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Set the GD pointer in the SPL to a defined symbol so various
functions from U-Boot can be used without adverse side effects.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds the groundwork for generating signed BootStream, which
can be used by the HAB library in i.MX28. We are adding a new target,
u-boot-signed.sb , since the process for generating regular non-signed
BootStream is much easier. Moreover, the signed bootstream depends on
external _proprietary_ _binary-only_ tool from Freescale called 'cst',
which is available only under NDA.
To make things even uglier, the CST or HAB mandates a kind-of circular
dependency. The problem is, unlike the regular IVT, which is generated
by mxsimage, the IVT for signed boot must be generated by hand here due
to special demands of the CST. The U-Boot binary (or SPL binary) and IVT
are then signed by the CST as a one block. But here is the problem. The
size of the entire image (U-Boot, IVT, CST blocks) must be appended at
the end of IVT. But the size of the entire image is not known until the
CST has finished signing the U-Boot and IVT. We solve this by expecting
the CST block to be always 3904B (which it is in case two files, U-Boot
and the hand-made IVT, are signed in the CST block).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.
As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.
Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Since Kbuild was introduced, warmboot_avp.o has been compiled
without -march=armv4t.
Makefile should be adjusted to pass a per-file option.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Fix the macros guarding the spl.h header for various platforms. Due to
a typo and a propagation of it, the macros went out-of-sync with their
ifdef check, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
U-Boot has supported two kinds of asm-offsets.h.
One is generic for all architectures and its source is located at
./lib/asm-offsets.c.
The other is SoC specific and its source is under SoC directory.
The problem here is that only boards with SoC directory can use
the asm-offsets infrastructure.
Putting asm-offsets.c right under CPU directory does not work.
Now a new demand is coming. PowerPC folks want to use asm-offsets.
But no PowerPC boards have SoC directory.
It seems inconsistent that some boards add asm-offsets.c to SoC
directoreis and some to CPU directories.
It looks more reasonable to put asm-offsets.c under arch/$(ARCH)/lib.
This commit merges asm-offsets.c under SoC directories into
arch/$(ARCH)/lib/asm-offsets.c.
By the way, I doubt the necessity of some entries in asm-offsets.c.
I am leaving refactoring to the board maintainers.
Please check "TODO" in the comment blocks in
arch/{arm,nds32}/lib/asm-offsets.c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Yuantian Tang <Yuantian.Tang@freescale.com>
U-Boot uses the 'mkimage' tool to produce various image types,
not only uImage image type. Rename the invocation name from
UIMAGE to MKIMAGE.
The following command was used to do the replacement:
git grep 'quiet_cmd_mkimage.* = UIMAGE' | cut -d : -f 1 | \
xargs -i sed -i "s@\(quiet_cmd_mkimage\)\(.*\) = UIMAGE @\1\2 = MKIMAGE@" {}
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Squash these warnings in pinmux.c found with GCC 4.8:
/arch/arm/cpu/armv7/exynos/pinmux.c: In function 'exynos_pinmux_config':
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'count' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:16: note: 'count' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:9: note: 'start' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:689:19: warning: 'bank' may be used uninitialized in this function [-Wmaybe-uninitialized]
s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
^
/arch/arm/cpu/armv7/exynos/pinmux.c:662:24: note: 'bank' was declared here
struct s5p_gpio_bank *bank;
^
/arch/arm/cpu/armv7/exynos/pinmux.c: In function 'exynos_pinmux_config':
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'count' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:16: note: 'count' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:9: note: 'start' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:689:19: warning: 'bank' may be used uninitialized in this function [-Wmaybe-uninitialized]
s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
^
/arch/arm/cpu/armv7/exynos/pinmux.c:662:24: note: 'bank' was declared here
struct s5p_gpio_bank *bank;
^
Note that the warning is bogus, the function can never be called with invalid
'peripheral' argument. GCC just cannot analyze this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
The s_init function is only called on SPL or XIP cases, so lets only
build it for them. This makes the #if logic within the function a bit
clearer as to when we are or are not calling things, and makes it easier
to see that for example preloader_console_init isn't ever called in the
non-XIP full U-Boot case.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables to run Trats2 board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Trats board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Universal board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
