Commit graph

13030 commits

Author SHA1 Message Date
Soren Brinkmann
19ee402d08 arm64: zynqmp: PM: Add IRQ
PM callbacks are delivered to the NS OS. Let the PM driver handle the
IRQ and retrieve callback data from the secure HW.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:08 +01:00
Jolly Shah
6a097b0d05 arm64: zynqmp: Reduced min-residency time for idle state node
Changed min-residence to 10ms(was 100 ms) for cpu-sleep-0.
Tried lower values 5ms and 8ms and it worked fine with Debug Off.
But to accommodate PM Debug On case, 10 ms is required. With this
change, low power idle state is into effect more frequently.
Measured boot time with PM debugs On and Off. No change observed
compared to 100ms value.

Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>
Tested-by: Koteswararao Nayudu <kotin@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Jyotheeswar Reddy
fec547397f arm64: zynqmp: DT: Fix typo in idle-states node definition
Fixed a typo in specifying "entry-method"

Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Shubhrajyoti Datta
941f61fe80 arm64: zynqmp: Update the OPPs for cpu freq
Add operating-points-v2.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Michal Simek
585ca873ef arm64: zynqmp: Add references to cpu nodes
Add missing references to all cpu nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:07 +01:00
Michal Simek
40d1f8af17 arm64: zynqmp: Wire QSPI boot mode for SPL
ZynqMP qspi driver is on the way to mainline

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:02 +01:00
Michal Simek
494fffe70d arm64: zynqmp: Add support for CG/EG/EV device detection
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.

These efuse bits are setup for certain devices.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
011f0c4f7c arm64: zynqmp: Add SD1 level shifter mode to alternative selection
Extend Kconfig to cover SD1 level shifter mode.

Reported-by: Jason Wu <jason.hy.wu@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Siva Durga Prasad Paladugu
89401481bd arm64: zynqmp: Enable config DEFINE_TCM_OCM_MMAP if CONFIG_MP defined
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
c85a6b79d1 tools: mkimage: Extend mkimage to also include pmufw
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.

This is generated command line when PMUFW_INIT_FILE is setup.

./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:57 +01:00
Siva Durga Prasad Paladugu
e042d36e17 arm64: zynqmp: Provide a Kconfig option to use specified memory for MMU table
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Siva Durga Prasad Paladugu
f322ad604e arm64: zynqmp: mp: Correct the R5 release sequence
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
   A53 can do speculative and may result in ECC failures
   if TCM's are not initialized. So, it is always better
   to disable dcaches before accessing TCM and enable back.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Michal Simek
62e950fad3 arm64: zynqmp: Remove slcr with mio status pin detection
This code is not used on this platform and it is not called.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:55 +01:00
Michal Simek
dea4d2f01d arm: zynq: Add mini u-boot configuration for zynq
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.

ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE  0x40000
was hardcoded.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:47 +01:00
Michal Simek
70ca290422 arm: zynq: Sort dts names
Sort names.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:45 +01:00
Michal Simek
bc133e80ae arm: zynq: Add board support for cc108
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:40 +01:00
Michal Simek
534f7e0235 arm: zynq: Sync location of DT properties with Linux
This is trival change which only ensures the same location with Linux
kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Sai Pavan Boddu
5fad1ab3d0 arm: zynq: Add device-type property for zynq ethernet phy nodes
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.

Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Chirag Parekh
57bcc7fd37 arm: zynq: Add SCL & SDA GPIO entries for recovery
Wire i2c pinmuxing gpio recovery for zc702.

Signed-off-by: Chirag Parekh <chiragp@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom McLeod
413ab5b0e1 arm: zynq: Add support for SYZYGY Hub board
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.

Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Heinrich Schuchardt
549d684d4e arm64: zynqmp: remove unnecessary logical constraint
In

if (a || b)
else if (!a)

the constraint (!a) is always true if else is reached and
can be removed.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Jagan Teki
52aaddd6f4 i.MX6: engicam: Add imx6q/imx6ul boards for existing boards
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
539b1e228f board: icore-rqs: Fix mmc get env device
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3

Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
152038ea18 i.MX6UL: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
1f6e9bd2a7 i.MX6Q: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Fabio Estevam
e2162d709f imx: Remove boolean parameter from wdog powerdown function
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.

It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.

While at it, rename it to imx_wdog_disable_powerdown().

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-27 10:34:49 +01:00
Fabio Estevam
b42287f4c9 imx: Also clear powerdown enable bit for WDOG3 on i.MX6ULL
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.

Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:40 +01:00
Fabio Estevam
23ecca2cd8 mx6ull: Fix WDOG3 base address
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:31 +01:00
Philipp Tomsich
f07d76c00d rockchip: fix turning off boot-mode via Kconfig
The ROCKCHIP_BOOT_MODE_REG option defaults to a hex value, so 0 will
show as 0x0 if a default is provided and changed via Kconfig.
However, it still will show as 0, if no default is given.

Consequently, the "is set to something other than 0" test in a
Makefile is cumbersome.  Instead this check can easily be performed in
the C-code.

This removes the ifeq-check from mach-rockchip/Makefile, adds a
matching #if-check to boot_mode.c and fixes resulting link issues (if
boot_mode.o was not included due to the Makefile check) by defining a
stub function (in case the functionality is not built in) for
setup_boot_mode in boot_mode.c.

Fixes: e306779 (rockchip: make boot_mode related codes reused across all platforms)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-26 14:57:11 +01:00
Philipp Tomsich
8c2bb589e2 rockchip: pinctrl: rk3399: add support for I2C8
The RK3399 has a total of 9 I2C controllers.  To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.

For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-26 00:39:08 +01:00
Alexey Brodkin
f2a226780f arc: cache: Add required NOPs after invalidation of instruction cache
As per ARC HS databook (see chapter 5.3.3.2) it is required to add
3 NOPs after each write to IC_IVIC which we do from now on.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
2017-11-24 19:38:23 +03:00
Alexey Brodkin
d764a20f2b arc: bootm: Move slave cores kick-starting under !fake
Currently slave cores will be kick-started even if we want
to dry run bootm which is not what we really want.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
2017-11-24 19:38:07 +03:00
Andy Yan
ecb103bf68 rockchip: check download key before bootup
Enter download mode if the download key pressed.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Converted printfs in boot_mode.c to debug/pr_err:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:24 +01:00
Andy Yan
b4d23f7643 rockchip: add support for enter to bootrom download mode
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Andy Yan
e3067793c3 rockchip: make boot_mode related codes reused across all platforms
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Kever Yang
6ba54058ed rockchip: sysreset: merge into one common driver
Use a common driver for all Rockchip SOC instead of one for each SoC.
Use driver_data for reg offset.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Philipp Tomsich
4bbb05bcb5 rockchip: rk3188: move CONFIG_SPL_* entries from rk3188_common.h to Kconfig
There still are a few CONFIG_SPL_* options selected using defines from
rk3188_common.h instead of via Kconfig.  This migrates those over to
Kconfig.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Philipp Tomsich
b82bd1f8d4 rockchip: back-to-bootrom: allow passing a cmd to the bootrom
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it.  There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.

All the existing call-sites are adjusted to match the changed function
signature.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
4d9253fb76 rockchip: rk3188: use boot0 hook to load up SPL in 2 steps
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.

With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.

Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
ecfd71891a rockchip: back-to-bootrom: replace assembly-implementation with C-code
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.

This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b4806d6f1f arm: provide a PCS-compliant setjmp implementation
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers.  One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.

To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
ff143d5556 arm: mark save_boot_params_ret as a function
As no '.type' was set for save_boot_params_ret in start.S, binutils
did not track whether it was emitted as A32 or T32.  By properly
marking save_boot_params_ret as a potential function entry, we can
make sure that the compiler will insert the appropriate instructions
for branching to save_boot_params_ret both for call-sites emitted as
A32 and T32.

Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
7776cc011d arm: make save_boot_params_ret prototype visible for AArch64
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).

This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b377d22264 rockchip: boot0 hook: support early return for RK3188/RK3066-style BROM
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.

To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
16d761e3dd bcm281xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
62269f02ab bcm235xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 5
- ran 'whitespace-cleanup'
2017-11-21 23:57:21 +01:00
Philipp Tomsich
a002077d7d socfpga: boot0 hook: adjust to unified boot0 semantics
With the updated boot0 semantics (i.e. giving the boot0-hook control
over when and where the vector table is emitted), the boot0-hook for
the socfpga needs to be adjusted.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Philipp Tomsich
14ad6eb264 rockchip: enable boot0-hook for all Rockchip SoCs
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
  instruction load and running by bootrom;

Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-11-21 23:57:21 +01:00
Kever Yang
cee7470cd8 rockchip: boot0: align to 0x20 for armv7 '_start'
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Philipp Tomsich
ef70a42f0f arm: boot0 hook: move boot0 hook before '_start'
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.

To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
  (1) if a boot0-hook is present it is inserted at the start of
      the image
  (2) if a boot0-hook is present, emitting the ARM vector table
      (and the _start) symbol are suppressed in vectors.S and
      the boot0-hook has full control over where and when it
      wants to emit these

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Antony Antony
6130b1f6bc sun50i: h5: Add NanoPi Neo Plus2 DT initial support
Add initial DT for NanoPi NEO Plus2 by FriendlyARM
- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
- 1 GB DDR3 RAM
- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
- micro SD card slot
- Gigabit Ethernet (external RTL8211E-VB-CG chip)
- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
- 2x USB 2.0 host ports

Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-21 19:11:57 +05:30
Antony Antony
8faac0941c arm64: sun50i-h5.dtsi : update to kernel 4.14
last Kernel commit of sun50i-h5.dtsi d86e63e1f0b7

Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-21 19:11:47 +05:30
Faiz Abbas
16fa2eb951 ARM: dra7: Kconfig: Add thermal configs for dra7xx and am57xx
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-21 08:03:39 -05:00
Faiz Abbas
12dd1e5c6a ARM: dts: OMAP5+: Add support for bandgap sensor in SPL
Mark bandgap node as uboot,dm-spl so that it can be accessed in spl

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-11-21 08:03:38 -05:00
Tom Rini
56d5a10f3a Merge git://git.denx.de/u-boot-i2c 2017-11-20 10:51:11 -05:00
Beniamino Galvani
456efb5127 odroid-c2: enable I2C
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-20 10:11:44 +01:00
Beniamino Galvani
f8d9ca1833 i2c: add Amlogic Meson driver
Add a driver for the I2C controller available on Amlogic Meson SoCs.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-20 10:11:34 +01:00
Fabio Estevam
74da017a49 mx6: Select MX6QDL option via Kconfig
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-20 10:01:35 +01:00
Peter Senna Tschudin
6b0071c110 mx53: Add Board support for GE PPD
Create board support for GE PPD, based on mx53loco.

Use mx53ppd_defconfig make target to configure for this board.

Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:59:02 +01:00
Martyn Welch
54d8d4942f arm: mx5: Add more register definitions
Add register definitions require for video configuration.

Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Martyn Welch
065a1ece7a pwm: imx: Enable PWM support on i.MX53
Add missing parts for i.MX53 PWM support

Acked-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Tom Rini
29c4992256 Merge git://git.denx.de/u-boot-dm 2017-11-19 20:35:45 -05:00
Landheer-Cieslak, Ronald
48c7f77128 Add UART base addresses for additional UARTs
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.

Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
2017-11-17 10:53:45 -05:00
Gan, Yau Wai
9587dee937 nios2: 10m50: Add CPU pre-relocation in device tree
Tag CPU with dm-pre-reloc to enable driver before
relocation.

Signed-off-by: Gan, Yau Wai <yau.wai.gan@intel.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-11-17 10:51:24 -05:00
Jorge Ramirez-Ortiz
9a16153834 configs: dragonboard410c: Save environment data on eMMC
Save the environment data at the end of the boot partition on emmc

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-11-17 07:44:13 -05:00
Kever Yang
21f4486faa armv8: update gd after relocate
We need to update gd in assamble code after relocate,
this is a fix to:
adc421e arm: move gd handling outside of C code

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-17 07:44:13 -05:00
Stephen Warren
49e93875a6 arm64: support running at addr other than linked to
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2017-11-17 07:44:13 -05:00
Neil Armstrong
ea990816fe arm: meson: Add supplementary ethernet registers definitions
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17 07:44:13 -05:00
Masahiro Yamada
d6a0c78a4e pylibfdt: compile pylibfdt only when dtoc/binman is necessary
Currently, pylibfdt is always compiled if swig is installed on your
machine.  It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.

"checkbinman" and "checkdtoc" are wrong.  It is odd that the final
build stage checks if we have built necessary tools.  If your platform
depends on dtoc/binman, you must be able to build pylibfdt.  If swig
is not installed, it should fail immediately.

I added PYLIBFDT, DTOC, BINMAN entries to Kconfig.  They should be
property select:ed by platforms that need them.  Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-17 07:43:32 -05:00
Neil Armstrong
cade865a43 arm: add initial support for Amlogic P212 based on Meson GXL family
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17 07:43:32 -05:00
Neil Armstrong
4862215649 ARM: dts: Synchronize Amlogic from Linux Mainline 4.13.5
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5

In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-17 07:43:32 -05:00
Felix Brack
c07bf9bea7 am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-17 07:43:32 -05:00
Tom Rini
35172cfee8 sandbox: Add clrbits/setbits macros
We borrow the macros for these functions from ARM and remove references
to '__raw_'.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-16 18:45:05 -07:00
Tom Rini
ebca2083d3 Merge git://www.denx.de/git/u-boot-marvell 2017-11-16 09:32:04 -05:00
Baruch Siach
8c1ce928f4 arm: mvebu: clearfog: update SPI flash DT description
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in
the device tree.

Add an alias to the SPI bus so that the 'sf' command can probe the flash on
bus 1.

Add the "spi-flash" compatible string to make the standard SPI flash driver
probe the device.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16 11:45:20 +01:00
Jon Nettleton
78aa018f07 arm: mvebu: Add board_setup for xhci hardware
This fixes the USB 3.0 support for the a38x SOC.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16 11:45:20 +01:00
Prabhakar Kushwaha
f53e12d80a driver: net: fsl-mc: Use base 16 in simple_strtoul
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:53:15 -08:00
Ashish Kumar
91fded6200 armv8: ls1088aqds: Add SD boot support for ls1088qds
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:52:19 -08:00
Ashish Kumar
099f4093a5 armv8: ls1088ardb: Add SD boot support for ls1088
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:51:46 -08:00
Ashish Kumar
f65425fb46 armv8: ls1088: Enable SATA for ls1088
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15 10:50:54 -08:00
Marek Vasut
2bfd43e550 ARM: rmobile: Fix eMMC signal voltage on Salvator-X/XS
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for Salvator-X/XS to describe the hardware correctly.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-12 16:17:31 -05:00
Tom Rini
3c674b7e87 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-11-09 08:11:30 -05:00
Lukasz Majewski
9c8979cdb7 imx7: Add include guards for include/asm/arch-mx7/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
e895e996ab imx5: Add include guards for include/asm/arch-mx5/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
90d0e38c1e imx6: Add include guards for include/asm/arch-mx6/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
a3eec24ad3 imx:display5: Add support for LWN's DISPLAY5 board
This commit provides support for LWN's IMX6Q based DISPLAY5 board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
ec1b26973c imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCs
This commit provides generic function to set the RGMII/HSIC IO voltage
level on iMX6 devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Fabio Estevam
b2e6ad451b mx51: Select the ESDHC_A001 erratum
When a high speed card is connected to mx51evk the following error is seen:

U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)

CPU:   Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC
Hit any key to stop autoboot:  0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed

The root cause for the failure is the eSDHC-A001 erratum:

"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf

Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.

The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.

Successfully tested with a high speed SD card on a mx51evk board.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
2017-11-07 10:13:11 +01:00
Fabio Estevam
5d09c27138 mx25: Select the ESDHC_A001 erratum
When a high speed card is connected to mx25 the following error is seen:

U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)

CPU:   Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C:   ready
DRAM:  64 MiB
No arch specific invalidate_icache_all available!
MMC:   FSL_SDHC: 0
*** Warning - read failed, using default environment
In:    serial
Out:   serial
Err:   serial
Net:   FEC
Hit any key to stop autoboot:  0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed

, which prevents any usage of the SD card.

The root cause for the failure is the eSDHC-A001 erratum:

"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf

Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.

Successfully tested with a high speed SD card on a mx25pdk board.

Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
2017-11-07 10:13:00 +01:00
Fabio Estevam
07df697e14 mx25: Move MX25 selection to Kconfig
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.

This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2017-11-07 10:12:50 +01:00
Klaus Goger
4f70039b36 rockchip: dts: rk3399: change sd-card io voltage to 3.0V
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Klaus Goger
366812fa26 rockchip: dts: Use defines for pin names in rk3399-puma.dtsi and rk3368-lion.dts
pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Philipp Tomsich
b1e1ce2cd4 rockchip: dts: rk3399-puma: update USB configuration
This change updates the USB configuration for the RK3399-Q7 in the DTS:
 * fixes the OTG board configuration by enabling it ('okay')
 * improves the speed of 'usb start' by disabling the unused EHCI/OHCI
   controllers

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Philipp Tomsich
f2a9513168 rockchip: dts: rk3399-puma: update usbhub_enable regulator
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
 * the GPIO polarity is GPIO_ACTIVE_LOW
 * should be set to inactive (enable-active-low) when boot-on settings
   are applied
 * it can be changed at runtime (i.e. remove the always-on)

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07 09:16:57 +01:00
Philipp Tomsich
df1e6212f9 rockchip: dts: rk3399-puma: fix the modelling of BIOS_DISABLE
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.

This fixes the mix-up and models it correctly:
 * the GPIO is low-active
 * the regulator should be enabled (enable-active-high) during
   boot-on initialisation

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-07 09:16:56 +01:00
Chris Brandt
fc85605018 cosmetic: rmobile: renesas spelled wrong
Renesas was spelled wrong.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
2017-11-06 09:59:03 -05:00
Patrice Chotard
e36591c350 spear: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for SPEAR
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
1537d38619 stv0991: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STV0991
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
3bc599c956 stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
fb48bc448c sti: fix STMicroelectronics copyright
Uniformize all STMicroelectronics copyrights headers for STi
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Dongjin Kim
568197fa03 ARM: dts: exynos: fix property values of LDO15/17 for ODROID-XU3/4
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".

Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-11-06 16:59:32 +09:00
Kever Yang
36de37f5ca rockchip: rk3328: fix rockchip_get_cru api
The API for get priv pointer is wrong, fix it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-01 11:21:32 +01:00
Fabio Estevam
e1f0715f64 wandboard: Add support for the MX6QP variant
Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-31 11:01:38 +01:00
Tom Rini
2d5e6b4aac Merge git://git.denx.de/u-boot-video 2017-10-29 10:11:08 -04:00
Tom Rini
bb3d9ed3a9 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-27 21:59:10 -04:00
Sumit Garg
9b3f40ad09 armv8: sec_firmware: Add support for loadables in FIT
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.

Brief description of implementation:
  Add two more address pointers (loadable_h, loadable_l) as arguments to
  sec_firmware_init() api.
  Create new api: sec_firmware_checks_copy_loadable() to check if loadables
  node is present in SEC firmware FIT image. If present, verify loadable
  image and copies it to secure DDR memory.
  Populate address pointers with secure DDR memory addresses where loadable
  is copied.

Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Sumit Garg
9781d9ff5f armv8: layerscape: Allocate 66 MB DDR for secure memory
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Ran Wang
d4c746c7b1 armv8: ls1088ardb: Enable USB command RDB qspi-boot
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:06 -07:00
Ran Wang
4417e83495 arm64: layerscape: Move CONFIG_HAS_FSL_XHCI_USB to Kconfig
Use Kconfig to select QE-HDLC and USB pin-mux.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:43:57 -07:00
Tom Rini
ae6ac0a06e Merge git://git.denx.de/u-boot-x86 2017-10-27 08:50:16 -04:00
Vasily Khoruzhick
1d7eef3f3f sunxi: video: add LCD support to DE2 driver
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-10-27 09:44:48 +02:00
Vasily Khoruzhick
79f285ddeb sunxi: video: split out PLL configuration code
It will be reused in new DM LCD driver.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2017-10-27 09:39:19 +02:00
Bin Meng
411898dc87 x86: acpi: Put sleepstates.asl to the common place
The supported sleep states are generic on Intel processors. Move the
ASL definition to the common place.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Bin Meng
dc80d3b230 x86: fsp: graphics: Add some notes about the graphics info hob
On some platforms (eg: Braswell), the FSP will not produce the
graphics info HOB unless you plug some cables to the display
interface (eg: HDMI) on the board. Add such notes in the FSP
video driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Bin Meng
4c9f4c5ee4 x86: braswell: cherryhill: Update dts for SPI lock down
Intel Braswell FSP requires SPI controller settings to be locked down,
let's do this in the chrryhill.dts and remove previous Kconfig option.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Bin Meng
fb2c53091f Revert "x86: fsp: Configure SPI opcode registers before SPI is locked down"
This reverts commit 1e6ebee667.

It's not appropriate to call the Intel SPI driver specific stuff in
the FSP codes. We may add a simple DTS property "intel,spi-lock-down"
and let the Intel SPI driver call these stuff instead.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-10-27 15:13:47 +08:00
Bin Meng
aa9c5956c9 x86: Fix ACPI resume dependency to MRC cache
In an S3 resume path, MRC cache is mandatory. Enforce the dependency
in the Kconfig.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Bin Meng
3a856473fd env: x86: braswell: Set ENV_IS_IN_SPI_FLASH as default
Imply does not work for a Kconfig choice. Update ENV_IS_IN_SPI_FLASH
to be the default one for Intel Braswell.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Bin Meng
4a5a7fcac2 x86: braswell: Fix unexpected crash during Linux kernel boot
It was observed that when booting Linux kernel on Intel Cherry Hill
board, unexpected crash happens quite randomly. Sometimes kernel
just oops, while sometimes kernel throws MCE errors and hangs:

  mce: [Hardware Error]: Machine check events logged
  mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 4: c400000000010151
  mce: [Hardware Error]: TSC 0 ADDR 130f3f2c0
  mce: [Hardware Error]: PROCESSOR 0:406c3 TIME 1508160686 SOCKET 0 APIC 0 microcode 363

This looks like a hardware error per mcelog. After debugging, it
seems turning off turbo mode on the processor does not expose this
behavior, although U-Boot runs OK with turbo mode on. Suspect it is
related to an errata of Braswell processor.

To fix this, remove the Braswell cpu driver which does the turbo
mode configuration, and switch to use the generic cpu-x86 driver.
Also there is a configuration option in the FSP that turns on the
turbo mode and that has been turned off too.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Icenowy Zheng
be5b96f0e4 sunxi: setup simplefb for Allwinner DE2
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.

Add code to setup simplefb for Allwinner DE2 driver.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-26 11:57:14 +02:00
Icenowy Zheng
f6bdddc92b video: add an option for video simplefb via DT
Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.

Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-26 11:53:39 +02:00
Icenowy Zheng
401a3ca0fb sunxi: change the DE1 video option to CONFIG_VIDEO_SUNXI
The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.

Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2017-10-26 11:48:49 +02:00
Maxime Ripard
819f1e081c sunxi: binman: Add U-Boot binary size check
The U-Boot binary may trip over its actual allocated size in the storage.
In such a case, the environment will not be readable anymore (because
corrupted when the new image was flashed), and any attempt at using saveenv
to reconstruct the environment will result in a corrupted U-Boot binary.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Maxime Ripard
ce2e44d836 sunxi: Enable THUMB build for the U-Boot binary
We start to get to the limit of our main U-Boot binary size (with some
boards even crossing it). Enable its build using thumb2 to get some extra
room.

Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Maxime Ripard
7514069aa3 sunxi: Add support for the Banana Pi M2-Magic
The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:06 +02:00
Quentin Schulz
c96f598be7 sunxi: clk: fix N formula for CPUX clocks
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).

This results in a clock set to a frequency that isn't specified as
possible for CPUs.

Let's use the correct formula.

Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-25 10:05:05 +02:00
York Sun
1e0d51a6c4 powerpc: mpc85xx: Implement CPU erratum A-007907 for secondary cores
Commit 06ad970b53 ("powerpc: mpc85xx: Implemente workaround for CPU
erratum A-007907") clears L1CSR2 for the boot core, but other cores
don't run through the workaround. Add similar code for secondary
cores to clear DCSTASHID field in L1CSR2 register.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-10-23 14:02:48 -07:00
Masahiro Yamada
624c0954c7 ARM: uniphier: use pr_*() more where appropriate
Commit dd74b945af ("ARM: uniphier: use pr_() instead of printf()
where appropriate"), but I missed to update this file for some reason.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:09:22 +09:00
Masahiro Yamada
272874879b ARM: dts: uniphier: sync DT with Linux 4.14-rc5
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Masahiro Yamada
9ac0e7b37a ARM: uniphier: split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL.  So, many nodes must
be marked as dm-pre-reloc to prevent fdtgrep from stripping them off.

Sprinkling U-Boot-specific properties all over the place is painful
because DT files are synced with Linux from time to time.

Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is
appended to UniPhier V7 DTS before the build.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-23 01:02:05 +09:00
Masahiro Yamada
d0df9588e8 ARM: uniphier: remove CONFIG_UNIPHIER_ETH
The option is never enabled by anyone.  Remove the code surrounded
by its ifdef.  This should be handled by the clock/reset drivers.

CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped
by the next resync.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Adam Ford
0a9ef45158 Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 16:44:07 -04:00
Bin Meng
83262f99cd x86: baytrail: fsp: Move Azalia update codes to board
Azalia configuration may be different across boards, hence it's not
appropriate to do that in the SoC level. Instead, let's make the
SoC update_fsp_azalia_configs() routine as a weak version, and do
the actual work in the board codes.

So far it seems only som-db5800-som-6867 board enables the Azalia.
Move the original codes into som-db5800-som-6867.c.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-10-19 11:37:51 +08:00
Bin Meng
f6859558ca x86: baytrail: fsp: Use a function to update the Azalia config pointer
At present we directly pass the Azalia config pointer to the FSP UPD.
This updates to use a function to do the stuff, like Braswell does.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-10-19 11:37:51 +08:00
Bin Meng
abddcd52ab x86: fsp: Consolidate Azalia header file
So far there are two copies of Azalia struct defines with one in
baytrail and the other one in braswell. This consolidates these
two into one, put it in the common place, and remove the prefix
pch_ to these structs to make their names more generic.

This also corrects reset_wait_timer from us to ms.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-10-19 11:37:51 +08:00
Bin Meng
3322a8e1a3 x86: Turn off running VGA ROM during S3 resume
This is only needed when graphics console is used. For kernel with
native graphics driver, this can be turned off to speed up.

Change this option's default to n in the Kconfig.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-10-19 11:37:51 +08:00
Bin Meng
febdfaabc7 x86: baytrail: Fix unstable ACPI S3 resume
It was observed that when booting a Ubuntu 16.04 kernel, doing ACPI
S3 suspend/resume sometimes causes the Ubuntu kernel hang forever.
The issue is however not reproduced with a kernel built from i386/
x86_64 defconfig configuration.

The unstability is actually caused by unexpected interrupts being
generated during the S3 resume. For some unknown reason, FSP (gold4)
for BayTrail configures the GPIO DFX5 PAD to enable level interrupt
(bit 24 and 25). As this pin keeps generating interrupts during an
S3 resume, and there is no IRQ requester in the kernel to handle it,
the kernel seems to hang and does not continue resuming.

Clear the mysterious interrupt bits for this pin.

Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-10-19 11:37:51 +08:00
Praneeth Bajjuri
9b46ce8cfc arm: dra76: fastboot: extend cpu type for getvar command
'commit fa24eca1f2 ("omap: Add routine for setting fastboot variables")'
adds initial support and usage of "fastboot getvar" command
for DRA75x and DRA72x devices.

and
'commit 0f9e6aee9d ("arm: dra76: Add support for ES1.0 detection")'
adds initial dra76 device definition

This patch is to extend usage of "fastboot getvar" for DRA76 device.

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Vishal Mahaveer
b6df93598c omap-common: fastboot: extend cpu type for DRA71x rev 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Extend support for this
revision in "getvar cpu" command.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
[praneeth@ti.com: rebase to u-boot master]
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Tuomas Tynkkynen
c68c03f52b Drop CONFIG_HAS_DATAFLASH
Last user of this option went away in commit:

fdc7718999 ("board: usb_a9263: Update to support DT and DM")

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-16 09:42:51 -04:00
Alexander Graf
409f05f259 fdt: update bcm283x device tree sources to Linux 4.14 state
Upstream Linux has received a few device tree updates to the RPi
which we should propagate into the builtin U-Boot one as well to
gain hardware support.

This patch bumps the dts files to their 4.14 Linux counterparts
with the exception of sdhost on 32bit RPi versions. There we stay
with iproc as the sdhost driver is missing in U-Boot.

Signed-off-by: Alexander Graf <agraf@suse.de>
2017-10-16 09:42:51 -04:00
Masahiro Yamada
c7372d61fd ARM: uniphier: adjust ifdefs for new UniPhier DWC3 CONFIG
Now USB 3.0 feature is enabled/disabled by CONFIG_USB_DWC3_UNIPHIER.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Masahiro Yamada
5e5edca27c ARM: uniphier: change the default of SoC select to UNIPHIER_V7_MULTI
ARCH_UNIPHIER_V8_MULTI depends on !SPL, so the default may be hidden.
Use a clearer default.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Masahiro Yamada
dd74b945af ARM: uniphier: use pr_() instead of printf() where appropriate
Replace printf() with pr_() to specify proper loglevel.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:24 +09:00
Masahiro Yamada
0f72b74b32 ARM: dts: uniphier: update GPIO nodes
Switch to the single node design.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:24 +09:00
Tom Rini
26f9184e09 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-12 13:36:58 -04:00
Marek Vasut
0a333602df ARM: imx6: Add DHCOM i.MX6 PDK board support
Add support for the DHCOM i.MX6 PDK board. This board has:
- FEC ethernet
- EHCI USB host
- 3x SDMMC

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2017-10-12 18:01:06 +02:00
Diego Dorta
e2000731ae mx6: sys_proto: Add prototypes for imx6_pcie_toggle() functions
When compiling with W=1 errors are observed:

drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void)

drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void)

Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:18 +02:00
Diego Dorta
342b4b09b1 mx6: clock: Add a prototype for do_mx6_showclocks()
When compiling with W=1 the following warning is observed:

arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])

Remove this warning by adding the function prototype into arch-mx6/clock.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:01 +02:00
Ilya Ledvich
6963204c4c arm: imx7d: add support for Compulab cl-som-imx7
Add initial support for Compulab cl-som-imx7 SoM.
The initial support includes:
 - MMC
 - eMMC
 - SPI flash
 - I2C
 - FEC
 - USB
 - Serial console

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
c5c6f37a04 imx: mx7: SPL support for i.MX7
Add configuration file and spl_boot_device function for the i.MX7 SPL.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
258bad41ac imx: mx7: DDR controller configuration for the i.MX7 architecture
The configuration files imximage.cfg are used for the DDR controller
configuration.
Add DDR configuration function to replace the DDR controller
configuration in the imximage.cfg file. The function can be used for
DDR size detection.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
8bf2d77806 imx: mx7: fix the CCM_ macros
The CCM_ macros use the CCM_BASE_ADDRESS macro, which doesn't exist.
Replace the CCM_BASE_ADDRESS macros with CCM_BASE_ADDR.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2017-10-12 17:31:16 +02:00
Diego Dorta
c49fa34e5b mx6: soc: Include <asm/bootm.h> header file
When compiling with W=1 the following warning is observed:

arch/arm/mach-imx/mx6/soc.c:213:12: warning: no previous prototype for ‘get_board_rev’ [-Wmissing-prototypes] u32 __weak get_board_rev(void)

Fix the build warning by including <asm/bootm.h>.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 17:31:16 +02:00
Diego Dorta
9f272573b7 imx: sys_proto: Add a prototype for board_mmc_get_env_dev()
When compiling with W=1 the following warning is observed:

board/freescale/mx6sabresd/mx6sabresd.c:266:5: warning:
no previous prototype for ‘board_mmc_get_env_dev’
[-Wmissing-prototypes] int board_mmc_get_env_dev(int devno)

Remove this warning by adding the function prototype into sys_proto.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-10-12 17:31:16 +02:00
Anatolij Gustschin
38df370182 imx6: disable clock command and print_cpuinfo code in SPL
We do not use print_cpuinfo and clock command code in SPL,
disable it when building SPL image.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-10-12 17:30:32 +02:00
Tom Rini
2ee87b0c1a Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2017-10-10 20:14:38 -04:00
Tom Rini
ebdd65258b Merge git://git.denx.de/u-boot-dm 2017-10-09 20:19:39 -04:00
Marek Vasut
17cf99a5bb ARM: rmobile: dts: Add SDR104/HS200 to Salvator-X
Add DT nodes to enable SDR104/HS200 modes on Salvator-X boards.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-10-10 08:22:54 +09:00
Tom Rini
74d90d17ee Merge git://git.denx.de/u-boot-video 2017-10-09 13:31:33 -04:00
York Sun
fb97b8621e armv8: layerscape: Enable falcon boot
Add jump_to_image_linux() for arm64. Add "noreturn" flag to
armv8_switch_to_el2(). Add hooks to fsl-layerscape to enable falcon
boot.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Łukasz Majewski <lukma@denx.de>
2017-10-09 08:48:45 -07:00
York Sun
7eb40f0f9d armv8: fsl-layerscape: Avoid running dram_init_banksize again
gd->ram_size is reduced in this function to reserve secure memory.
Avoid running this function again to further reduce memory size.
This fixes issue for SPL boot with PPA image loaded in which case
secure memory is incorrectly allocated due to repeated calling.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-09 08:48:44 -07:00
York Sun
d1fc0a31b5 spl: fix assignment of board info to global data
Commit 15eb1d43bf ("spl: reorder the assignment of board info to
global data") intended to move assignment of board info earlier,
into board_init_r(). However, function preload_console_init() is
called either from spl_board_init() or from board_init_f(). For the
latter case, the board info assignment is much earlier than proposed
board_init_r(). Create a new function to fill gd->bd and call this
function when needed.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Ravi Babu <ravibabu@ti.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-09 08:48:44 -07:00
Sumit Garg
710d0cd79e armv8: fsl-layerscape: Allocate Secure memory from first ddr region
This change is required due to trusted OS (OP-TEE) not being position
independent code, it requires compile time fixed base address.

To take care of this it is assumed that all layerscape armv8 platforms
has minimum 2G ddr in first region. So we can have fixed address
space (66 MB -> (2MB for PPA + 64MB for trusted OS)) allocated from
top of first 2G ddr region and compile trusted OS with this fixed
base address.

But one exception here is ls1012 where we have only 1G (rdb) or 512M
(frdm) ddr memory. For those we can have different fixed compile time
base addresses for trusted OS.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-09 08:48:44 -07:00
Ran Wang
7458c5e65f armv8: Apply workaround for USB erratum A-009007 to LS1088A
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-09 08:36:37 -07:00
Heinrich Schuchardt
04d0da5157 sandbox: avoid memory leak in os_dirent_ls
Realloc does not free the old memory area if it fails.

Identified by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-08 20:41:09 -06:00
Patrice Chotard
d8f69e563b ARM: DTS: stm32: add SDMMC support fo stm32h743-eval
Add pinctrl and sdmmc nodes to add MMC support for
STM32H743 evaluation board.

Evaluation board needs a second pinctrl node
"pinctrl_sdmmc1_level_shifter" to drive a level shifter
on MMC bus.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-10-08 16:19:56 -04:00
Patrice Chotard
eccac3e120 ARM: DTS: stm32: add SDMMC support for stm32h743 disco
Add pinctrl and sdmmc nodes to add MMC support for
STM32H743 discovery board.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-10-08 16:19:56 -04:00
Bo Shen
72dee54b4e ARM: stm32f7: fix prescaler calculation of timer
As the timer 2 is on APB1 bus, the maximum of clock frequency of APB1 timer
clock is half of SYSCLK. Then to calculate the timer prescaler for timer 2
which need to be divided by 2.

Signed-off-by: Bo Shen <voice.shen@gmail.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-10-08 16:19:56 -04:00
Patrice Chotard
75d5853ffc serial: stm32x7: remove stm32f7-usart and stm32h7-usart compatible
This patch remove the extra compatibility string "st,stm32h7-usart"
and "st,stm32f7-usart" to avoid confusion, save some time & space.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-10-08 16:19:56 -04:00
zijun_hu
34f9a92583 ARMv8: make master CPU checking logic more clear
macro branch_if_master checks master CPU via (Aff3 & (Aff2:Aff1:Aff0))
it is simple but a little obscure.

fix by checking Affx fields within MPIDR_EL1 directly.

Signed-off-by: zijun_hu <zijun_hu@htc.com>
2017-10-08 16:19:56 -04:00
zijun_hu
7baf952fdb ARMv8: fix error in freeing stack frame
relocate_code() allocates 32 bytes stack frame but only 16 bytes are
freed before return. it will cause errors to possible previous frames
and doesn't make relocate_code() look like a function.

fix by freeing 32 bytes stack space

Signed-off-by: zijun_hu <zijun_hu@htc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-08 16:19:56 -04:00
zijun_hu
01a8359989 ARMv8: get new GD address from gd->new_gd directly
the new GD address is calculated via board data BD currently
it require the new GD area locates below BD tightly, so a strict
constraint is imposed on memory layout which maybe make special
platform unpleasant.

fix it by getting new GD address from gd->new_gd directly.

Signed-off-by: zijun_hu <zijun_hu@htc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-08 16:19:56 -04:00
Tom Rini
83e92f79d3 Merge git://git.denx.de/u-boot-x86 2017-10-07 09:12:04 -04:00
Andy Shevchenko
39665beed6 x86: tangier: Enable ACPI support for Intel Tangier
Intel Tangier SoC is a part of Intel Merrifield platform which doesn't
utilize ACPI by default. Here is an attempt to unleash ACPI flexibility
power on Intel Merrifield based platforms.

The change brings minimum support of the devices that found on
Intel Merrifield based end user device.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-10-07 15:07:59 +08:00
Sam Protsenko
268577669a omap: Fix warning when looking for userdata part
When eMMC was formattaed for Linux partition table, "userdata" partition
is missing. In this case, part_get_info_by_name() iterates over all
registered drivers (which are PART_TYPE_EFI, PART_TYPE_DOS and
PART_TYPE_ISO). And when it comes to PART_TYPE_ISO (which has empty
partition table), we can see next warning in U-Boot output:

    ** First descriptor is NOT a primary desc on 1:1 **

This patch switches to part_get_info_by_name_type() API in order to
check only EFI partitions for "userdata" partitions. This eliminates
mentioned warning.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-06 11:28:17 -04:00
Sam Protsenko
19d141a0f9 omap: Omit fastboot.userdata_size related errors
When using regular $partitions variable (for Linux boot), we can see
some unwanted messages:

> ERROR: cannot find partition: 'userdata'

> at arch/arm/mach-omap2/utils.c:96/omap_mmc_get_part_size()
> Warning: fastboot.userdata_size: unable to calc

Let's remove those, as missing 'userdata' partition is correct behavior
for Linux partition, and we don't want to see some Android-related
messages in this case.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-10-06 11:28:16 -04:00
Tuomas Tynkkynen
32f1182926 ARM: Add a new arch + board for QEMU's 'virt' machine
This board builds an U-Boot binary that is bootable with QEMU's 'virt'
machine on ARM. The minimal QEMU command line is:

    qemu-system-arm -machine virt,highmem=off -bios u-boot.bin

(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
    - u-boot.bin loaded and executing in the emulated flash at address 0x0
    - A generated device tree blob placed at the start of RAM
    - A freely configurable amount of RAM, described by the DTB
    - A PL011 serial port, discoverable via the DTB
    - An ARMv7 architected timer
    - PSCI for rebooting the system
    - A generic ECAM-based PCI host controller, discoverable via the DTB

Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:

- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
    -drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
    -net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
    -device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
    -drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-06 11:28:16 -04:00
Jean-Jacques Hiblot
a4d72869f8 omap: detect board before spl_early_init()
In order to be able to select the right DTB, we need to have identified the
board before spl_early_init() is called.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-06 11:27:40 -04:00
Tom Rini
4f42a0d721 Merge git://git.denx.de/u-boot-sunxi 2017-10-05 08:26:36 -04:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Masahiro Yamada
b44b30260f printk: collect printk stuff into <linux/printk.h> with loglevel support
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*().  U-Boot does not support them in a clean
way.  So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.

We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround.  Hence this
patch, to find the best home for all printk variants.  If you want to
use printk() and friends, please include <linux/printk.h>.  This header
is self-contained, and pulls in only a few headers.

When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards.  This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.

To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel".  (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.

The difference is the loglevel is build-time determined.  To save the
image size, lower priority pr_*() are compiled out.  I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.

I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 10:31:17 -04:00
Maxime Ripard
9f35688349 sunxi: usb_phy: invert the USB phy_ctl condition
All the new SoCs from Allwinner since the A33 have had the phy_ctl offset
at 0x410 instead of 0x404 that was used on the previous SoCs.

Instead of adding more and more special cases as the number of SoCs grow,
let's invert the test to have 0x410 by default, and the (hopefully) fixed
number of old SoCs being the exception.

Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-03 19:12:06 +02:00
Jagan Teki
ea5b1e1efb sun7i: a20: Add Bananapi M1 Plus support
Banana Pi M1 Plus is an open-source single-board computer
that adds more connectivity to the classic board using
Allwinner A20 SOC.

Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply

For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-10-03 19:12:06 +02:00
Chen-Yu Tsai
1328a81621 sunxi: rename Bananapi M3 dts file name
The upstream (Linux) device tree file for the Bananapi M3 follows the
convention of using the well known brand name, instead of the vendor
name, for naming. The file was recently added to upstream in commit
359b5a1e1c2d ("ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi
BPI-M3")

Rename the device tree file in U-boot to match.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
3c989f3a19 sunxi: Fix USB_GADGET implication
USB_GADGET will fail to compile if USB_MUSB_GADGET is not defined. Make
sure we have that condition right.

Fixes: e0ea88042d51 ("sunxi: Imply USB_ETHER")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
8829076a5b arm: sunxi: Move spl_boot_device in a separate function
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.

Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.

Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Stefan Mavrodiev
6ee9d7be06 sunxi: Add support for A20-OLinuXino-MICRO-eMMC
From rev.J A20-OLinuXino-MICRO has eMMC option. For now this is
only 4GB, but in the future size may increase.

The dts file is the same from mainline kernel.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
a12fb0e368 sunxi: Enable CMD_GPT by default
GPT is pretty common these days and can be useful for things like fastboot.
Add a platform imply, so that users can still opt out if they wish so.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
5ed8239383 sunxi: sina33: Sync the device tree with the kernel
The kernel DT of the SinA33 has evolved quite a bit. Make sure we sync it
and its upstream DTSI to be able to use the OTG. The DTs were taken from
the 4.13 kernel release.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
6e2166c186 sunxi: Imply USB_ETHER
Now that we can enable the usb_ether gadget, do it. This will be especially
useful for boards that don't have any ethernet controller, such as the ones
based on the A13 or A33.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
3a61b080ac musb: sunxi: switch to the device model
The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.

Switch to probing both in peripheral and host mode through the DT.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
cfa34996b0 cmd: fastboot: Rework fastboot dependency
Fastboot need a bunch of options to be operating properly, such as the
g_dnl gadget, the fastboot command, and some options that make sense. Since
fastboot is now part of Kconfig, make sure we have them right.

That will also reduce the boilerplate in the defconfigs.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
654b02b18c sunxi: imply USB_GADGET
A good number of our boards have USB_GADGET enabled. Imply it so that all
the boards can benefit from it, and remove some boilerplate from our
defconfigs.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
a95aee6af7 usb: gadget: Make g_dnl USB settings common
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.

Make them common by renaming them, and convert all the users.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
a4dd8722fa sandbox: Expand list of IO accessors
The setbits/clrbits/clrsetbits macros are used widely across the tree,
let's provide implementation for them in the sandbox.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:04 +02:00
Paul Burton
f7ae1ca3e8 sandbox: Use asm-generic/io.h
Convert the sandbox architecture to make use of the new asm-generic/io.h
to provide address mapping functions. As sandbox actually performs
non-identity mapping between physical & virtual addresses we can't
simply make use of the generic mapping functions, but are able to
implement phys_to_virt() & make use of it from map_physmem().

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2017-10-02 21:52:24 -04:00
Paul Burton
ae07d609e9 powerpc: Use asm-generic/io.h
Convert the powerpc architecture to make use of the new asm-generic/io.h
to provide address mapping functions. As powerpc can actually perform
non-identity mapping between physical & virtual addresses we can't
simply make use of the generic phys_to_virt() & virt_to_phys()
functions. However since map_physmem() already effectively implemented
the same thing as virt_to_phys() we can simply implement virt_to_phys()
instead of map_physmem() & use the generic map_physmem(). We also drop
the no-op unmap_physmem().

This has only been build-tested, feedback from architecture maintainers
is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Wolfgang Denk <wd@denx.de>
2017-10-02 21:52:23 -04:00
Paul Burton
e16986c481 nios2: Use asm-generic/io.h
Convert the nios2 architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As nios2 actually performs
non-identity mapping between physical & virtual addresses we can't
simply make use of the generic functions, with the exception of being
able to drop our no-op unmap_physmem() and definitions of unused map
flags.

Feedback from architecture maintainers is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
2017-10-02 21:52:23 -04:00
Paul Burton
d1cbeafd5e mips: Use asm-generic/io.h
Convert the mips architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As mips actually performs
non-identity mapping between physical & virtual addresses we can't
simply make use of the generic functions, with the exception of being
able to drop our no-op unmap_physmem() and definitions of unused map
flags.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2017-10-02 21:52:23 -04:00
Paul Burton
e8645527b1 xtensa: Use asm-generic/io.h
Convert the xtensa architecture to make use of the new asm-generic/io.h
to provide address mapping functions. As the generic implementations are
suitable for xtensa this is primarily a matter of moving code.

This has only been build-tested, feedback from architecture maintainers
is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
2017-10-02 21:52:22 -04:00
Paul Burton
6f01316f36 x86: Use asm-generic/io.h
Convert the x86 architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for x86 this is primarily a matter of moving code.

This has only been build-tested, feedback from architecture maintainers
is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-02 21:52:22 -04:00
Paul Burton
505fe9cdd0 sh: Use asm-generic/io.h
Convert the sh architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for sh this is primarily a matter of moving code.

Feedback from architecture maintainers is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-10-02 21:52:21 -04:00
Paul Burton
b3666a693a nds32: Use asm-generic/io.h
Convert the nds32 architecture to make use of the new asm-generic/io.h
to provide address mapping functions. As the generic implementations are
suitable for nds32 this is primarily a matter of removing code.

Feedback from architecture maintainers is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Macpaul Lin <macpaul@andestech.com>
2017-10-02 21:52:21 -04:00
Paul Burton
dbee715237 microblaze: Use asm-generic/io.h
Convert the microblaze architecture to make use of the new
asm-generic/io.h to provide address mapping functions. As the generic
implementations are suitable for microblaze this is primarily a matter
of removing code.

Feedback from architecture maintainers is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Michal Simek <monstr@monstr.eu>
2017-10-02 21:52:21 -04:00
Paul Burton
0884077b70 m68k: Use asm-generic/io.h
Convert the m68k architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for m68k this is primarily a matter of emoving code.

Feedback from architecture maintainers is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Huan Wang <alison.wang@freescale.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
2017-10-02 21:52:20 -04:00
Paul Burton
8f8e6304df arm: Use asm-generic/io.h
Convert the arm architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for arm this is primarily a matter of removing code.

This has only been build-tested, feedback from architecture maintainers
is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-02 21:52:20 -04:00
Paul Burton
593477c6b3 arc: Use asm-generic/io.h
Convert the arc architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for arc this is primarily a matter of removing code.

Feedback from architecture maintainers is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
2017-10-02 21:52:20 -04:00
Kever Yang
e19fa89c9d rockchip: enable TPL_SYSRESET for all rockchip SoCs
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need TPL_SYSRESET
for do_reset() in TPL for Rockchip SoCs.

References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_)
macro"

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:35 +02:00
Jagan Teki
2ee3021ae1 rk3288: spl: Add dram_init_banksize
Falcon mode, is updating DDR dt node configuration through
spl_fixup_fdt() so add appropriate DDR base and size through
dram_init_banksize.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:35 +02:00
Philipp Tomsich
482cf22333 rockchip: rk3399-puma: add boot-on regulator to override BIOS_DISABLE
The (Qseven) BIOS_DISABLE signal on the RK3399-Q7 (Puma) keeps the
eMMC and SPI in reset initially and we need to write a GPIO to turn
them on before continuing the boot-up.

This adds the DTS entries for the additional regulator and makes
pinctrl and gpio3 available during SPL.  It also adds a hook to the
spl_board_init() to ensure that the regulator gets probed and enabled.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:35 +02:00
Philipp Tomsich
775bd78a11 rockchip: dts: rk3399-puma: add 'same-as-spl' to the front of the boot-order
In the general case, we want to continue booting the full U-Boot
(contained in a discoverable FIT image) from the same device the SPL
stage was loaded from.  This prepends the 'same-as-spl' specifier to
our configurable boot-order to make this the default behaviour.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:35 +02:00
Philipp Tomsich
c55addd360 rockchip: spl: rk3399: implement chip-specific board_spl_was_booted_from()
To support the new "same-as-spl" specifier in the boot-order on the
RK3399, this implements the chip-specific mapping from the information
obtainable from the BROM to a OF path name.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:34 +02:00
Philipp Tomsich
80e9f88e67 rockchip: spl: support a 'same-as-spl'-specifier in the spl-boot-order
It is often desirable to configure the spl-boot-order (i.e. the order
that SPL probes devices to find the FIT image containing a full U-Boot)
such that it contains 'the same device the SPL stage was booted from'
early on.  To support this, we introduce the 'same-as-spl' specifier
for the spl-boot-order property.

This commit adds:
 - documentation for the new board_spl_was_booted_from() function that
   individual SoCs/boards should provide, if they can determine where
   the SPL was booted from
 - implements the new board_spl_was_booted_from() stub function
 - adds support for handling the 'same-as-spl' specifier and calling
   into the per-SoC/per-board support code.

This also updates the documentation for the 'u-boot,spl-boot-order'
property.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:34 +02:00
Philipp Tomsich
dbad01cab5 rockchip: spl: add documentation for spl_node_to_boot_device()
In the expectation that the spl-boot-order code will eventually
gain use outside of mach-rockchip: let's add documentation on the
spl_node_to_boot_device() function, which is likely to become a
publicly exported function.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:34 +02:00
Philipp Tomsich
3b4f87735d rockchip: bootrom: add definitions to retrieve BROM boot-source
The Rockchip BROM allows reading where it booted from from SRAM.
This adds the necessary definitions (as received from Kever) for
the location of this information in the RK3399's SRAM and naming
for the constants used.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:34 +02:00
Philipp Tomsich
fb7406469c rockchip: rk3399: make spl_board_init board-specific
The later-stage spl_board_init (as opposed to board_init_f) should set
up board-specific details: these differ between the EVB-RK3399 and the
RK3399-Q7 (Puma).

This moves spl_board_init back into the individual boards and removes
the unneeded functionality from Puma.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:34 +02:00
Kever Yang
4a18729726 rockchip: rk322x: update the sysreg number for boot mode
The boot mode for rk322x is stored in sysreg 0, update it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:34 +02:00
Elaine Zhang
f9674f5eec rockchip: dts: rk3328-evb: add i2c1 and rk805 nodes
add i2c1 and rk805 nodes to support rk805 init setting.

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Jagan Teki
532cb7f5ad rk3288: vyasa: Add TPL support
Since the size of SPL can't be exceeded 0x8000 bytes in RK3288,
it is not possible add new SPL features like Falcon mode or etc.

So add TPL stage so-that adding new features to SPL is possible.
- TPL: DRAM init, clocks
- SPL: MMC, falcon, etc

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Jagan Teki
a982d5156d armv7: rk3288: Move configure_l2ctlr to common
configure_l2ctlr will be shared between SPL and TPL so
move them into asm/arch/sys_proto.h

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Jagan Teki
d9a7dcf5b8 armv7: Move L2CTLR read/write to common
L2CTLR read/write functions are common to armv7 so, move
them in to include/asm/armv7.h and use them where ever it need.

Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Backed out the change to arch/arm/mach-tegra/cache.c:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Kever Yang
04e97e48d0 rockchip: rk3036: fix grf macro define
Some of macros definition are not correct, fix them according to TRM.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
Philipp Tomsich
cbe18f10e6 rockchip: rk3399: spl: convert to using BOOT_DEVICE_BOOTROM
Instead of directly calling into the back-to-bootrom code, the RK3399
common SPL implementation now uses BOOT_DEVICE_BOOTROM to trigger a
transfer back into the bootrom.

With this factored out, the spl_board_init function can not be
customised for each RK3399 board.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:32 +02:00
Kever Yang
ffd1cd67da rockchip: dts: rk3229: remove dram channel info
The dram channel info will be auto detect by the driver,
we do not need it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-10-01 00:33:32 +02:00
Kever Yang
0176399b79 rockchip: rk322x: add sdram driver
Add driver for rk322x to support sdram initialize in SPL.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
Kever Yang
f0768491db rockchip: rk3328: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Kever Yang
c9eb7bca4b rockchip: rk3288: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Kever Yang
5b67d7010b rockchip: rk3188: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Kever Yang
b5934cf67c rockchip: rk3399: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Philipp Tomsich
8e8bcccc18 rockchip: imply ADC and SARADC_ROCKCHIP for Rockchip SOCs
Enable the Rockchip SARADC driver for all Rockchip SoCs.

Note that the SARADC peripheral is available on all SoCs except the
RK3036 and RK3228.  However, as this is a DM-driver, enabling by
default will not cause any function problems (and can always be
changed from defconfig, if size is a concern).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
2017-10-01 00:33:31 +02:00
David Wu
3b4cab15ac rockchip: dts: Enable SARADC for rk3399-evb
Enable the SARADC for download key pressed detect.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
David Wu
6333a3bad9 rockchip: dts: Enable SARADC for rk3368-sheep
Enable the SARADC for download key pressed detect.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
David Wu
0ac1ae65ea rockchip: dts: Enable SARADC for rk3368-px5-evb
Enable the SARADC for download key pressed detect.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
f957dec682 rockchip: dts: Enable SARADC for rk3328-evb
Enable the SARADC for download key pressed detect.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
0eaf58bfaa rockchip: dts: Enable SARADC for rk3288-popmetal
Enable the SARADC for download key pressed detect.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
679276bde6 rockchip: dts: Enable SARADC for rv1108-evb
Enable the SARADC for download key pressed detect.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
fdc1eccbd1 rockchip: dts: rv1108: Add SARADC node at dtsi level
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
615514c16d rockchip: clk: Add rk3368 SARADC clock support
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
2e4ce50d1a rockchip: clk: Add rv1108 SARADC clock support
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:29 +02:00
Karthik Tummala
8adb6ec885 arm: dts: omap3: sync DTS with Linux 4.14-rc1
This re-syncs omap3 DTS file with current file from
Linux v4.14-rc1 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from usbhsohci,
usbhsehci, ssi_port1 and ssi_port2 sub nodes.

Signed-off-by: Karthik Tummala <karthik@techveda.org>
2017-09-29 14:07:57 -04:00
Lokesh Vutla
df518f804f ARM: dts: OMAP5+: Enable all gpios in SPL
With DM enabled, gpio numbering is assigned based on the
probed order of gpios, irrespective of the gpio base. So enable
all necessary gpios in SPL.

Fixes: edf25d94d55c (“ARM: dts: OMAP5+: Enable gpio in SPL”)
Reported-by: Gou, Hongmei <h-gou@ti.com>
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-29 14:07:56 -04:00
Madan Srinivas
0830d72bb9 arm: am33xx: security: adds auth support for encrypted images
This patch adds support for authentication of both plain
text and encrypted binaries. A new SECDEV package is needed
to enable encryption of binaries by default for AM3x.

The ROM authentication API detects encrypted images at
runtime and automatically decrypts the image if the
signature verification passes.

Addition of encryption on AM3x results in a change in the
image format. On AM4x, AM5x and, on AM3x devices signing
clear test images, the signature is appended to the end of the
binary.

On AM3x, when the SECDEV package is used to create signed
and encrypted images, the signature is added as a header
to the start of the binary. So the binary size calculation
has been updated to reflect this change.

The signing tools and encrypted image format for AM3x
cannot be changed to behave like AM4x and AM5x to
maintain backward compatibility with older Sitara
M-Shield releases.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-09-29 14:07:55 -04:00
Adam Ford
b85781c2a8 ARM: omap3: am3517-evm: Add device tree and DM support
With the device tree ported from Linux 4.13, this enables
Driver Model and Device Tree support for the am3517-evm

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
2017-09-29 14:07:54 -04:00
Adam Ford
a56fd949a5 arm: dts: am3517_evm: Sync DTS files with Linux 4.13-RC5
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.

There are some spacing issues in the patch, but they appear to be
present in the Linux source files.  I'll try to get to fixing them there,
and do a future re-sync at a later date.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
2017-09-29 14:07:54 -04:00
Tom Rini
ff6c3125e7 TI: ARCH_OMAP2PLUS: Enable SPL_STACK_R and provide default value
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it.  select this and re-sync the defconfigs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-29 14:07:51 -04:00
Adam Ford
c774207f48 ARM: da850-evm: Enable DM_I2C
With DM now enabled with the device tree pulled from Linux, we can
enable DM_I2C in U-Boot.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add DM_I2C_COMPAT to da850_am18xxevm to fix warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-29 14:07:18 -04:00
Wenyou Yang
40f3429415 board: at91sam9x5ek: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-29 17:51:56 +02:00
Wenyou Yang
e974b08119 board: sama5d4_xplained: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-29 17:51:22 +02:00
Wenyou Yang
4b0467db53 board: sama5d4ek: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-29 17:50:44 +02:00
Wenyou Yang
fe32c6d159 board: sama5d3xek: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-29 17:50:04 +02:00
Wenyou Yang
d2cd09bb44 board: sama5d2_xplained: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-29 17:48:56 +02:00
Adam Ford
4c70755986 arm: dts: da850: Migrate da850-evm DTS files from Linux 4.13-RC5
A few small additional items are needed to support DM_SPI and
DM_SERIAL, so those were added to da850-evm-u-boot.dtsi

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-29 10:52:20 -04:00
rick
9c7ffc94dc nds32: Fix io.h warning message about readb
It is caused from asm/io.h declare different input type.

Signed-off-by: rick <rick@andestech.com>
2017-09-28 13:16:54 +08:00
Baruch Siach
f3a88e2ca1 arm: mvebu: fix boot from UART on ClearFog Base
The ClearFog Base boot from UART when setting the DIP switches to 01001.
Unfortunately, the SPL code sometimes fails to detect the UART boot
method at run-time. Add an alternative SAR UART boot value to fix this.

Note that this alternative value is not documented (Armada 38x Hardware
Specifications, Table 48). But experimentations showed it on the
ClearFog Base.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:53:18 +02:00
Chris Packham
c3ab274444 ARM: mvebu: handle unused DRAM banks with ECC enabled
dram_ecc_scrubbing() had code to skip unused DRAM banks but it would not
work because mvebu_sdram_bs() returns 0 and the code was subtracting 1
before checking the size. Remove the -1 from the bank size and the +1
from the total which will skip unused banks and still calculate the
correct size. Put the -1 where it is needed for scrubbing via the xor
engine.

Reported-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:52:57 +02:00
Chris Packham
0a91e1cce4 ARM: mvebu: add SAR frequency values for 1.8/2.0GHz
The Armada-38x has 1.8GHz and 2.0GHz variants. Add entries for these
variants to the sar_freq_tab.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:54 +02:00
Joshua Scott
631407c5c0 ARM: mvebu: add additional information to board_add_ram_info()
Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is

  SoC:   MV88F6820-A0 at 1600 MHz
  DRAM:  2 GiB (800 MHz, 32-bit, ECC not enabled)

Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:50 +02:00
Chris Packham
0f8031a333 ARM: mvebu: Add SoC IDs for Marvell's integrated CPUs
These SoCs are network packet processors (switch chips) with integrated
ARMv7 cores. They share a great deal of commonality with the Armada-XP
CPUs.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:43 +02:00
Chris Packham
7654f62f4e ARM: mvebu: Convert CONFIG_MVNETA to Kconfig
This converts the following to Kconfig:
   CONFIG_MVNETA

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:30 +02:00
Marek Vasut
891ac390b8 ARM: dts: rmobile: Add PHY reset GPIO
The PHY reset GPIOs were missing from the DT, add them.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-24 14:12:07 +09:00
Tom Rini
0929863aff Merge git://git.denx.de/u-boot-socfpga 2017-09-23 17:32:53 -04:00
Masahiro Yamada
5e8c39d4f4 ARM: socfpga: fix duplicate const specifier warning
GCC 7.1 warns:
duplicate ‘const’ declaration specifier [-Wduplicate-decl-specifier]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-23 15:13:20 +02:00
Sriram Dash
0d7f1ae0fe armv8: fsl: i2c: Put I2C related code under CONFIG_SYS_I2C
I2C code is put under CONFIG_SYS_I2C.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:45:27 -07:00
Sriram Dash
e45ff0ce63 armv8: fsl: ifc: Put IFC related code under CONFIG_FSL_IFC
IFC code is put under CONFIG_FSL_IFC

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:45:17 -07:00
Santan Kumar
77dc01bdc1 board/ls2081ardb: Update QSPI flash type from n25q512a to s25fs512s
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:41:54 -07:00
Ashish Kumar
bdbcb52256 armv8: fsl-layerscape: Put SATA code under SATA configs
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:41:24 -07:00
Felix Brack
7cc238f2ee arm: am33xx: Make pin multiplexing functions optional
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-22 07:40:04 -04:00
Patrice Chotard
246771b184 board: Add stm32h7 SoC, discovery and evaluation boards support
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.

For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:40:03 -04:00
Patrice Chotard
a1e384b4d9 ARM: DTS: stm32: adapt stm32h7 dts files for U-boot
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :

_ Add RCC clock driver node and update all clocks phandle
  accordingly.

  By default, on kernel side, all clocks was temporarly
  configured as a phandle to timer_clk waiting for a RCC
  clock driver to be available.
  On U-boot side, we now have a dedicated RCC clock driver, we
  can configured all clocks as phandle to this driver.

  All this binding update will be available soon in a kernel tag,
  as all the bindings have been acked by Rob Herring [1].

  [1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html

_ Align STM32H7 serial compatible string with the one which will be
  available in next kernel tag. The bindings has been acked by
  Rob Herring [2].
  This compatible string will be usefull to add stm32h7 specific
  feature for this serial driver.

  [2] https://lkml.org/lkml/2017/7/17/739

_ Add gpio compatible and aliases for stm32h743

_ Add FMC sdram node with associated new bindings value to
  manage second bank (ie bank 1).

_ Add missing HSI and CSI oscillators nodes needed
  by STM32H7 RCC clock driver.

  Clock sources could be:
	_ HSE (High Speed External)
	_ HSI (High Speed Internal)
	_ CSI (Low Power Internal)

  These clocks can be used as clocksource in some configuration.
  By default, HSE is selected as clock source.

_ Set HSE to 25Mhz for stm32h743i-disco and eval board

  By default, the external oscillator frequency is defined at
  25 Mhz in SoC stm32h743.dtsi file.
  It has been set at 125 Mhz in kernel DT temporarly waiting for
  RCC clock driver becomes available.

  As in U-boot we got a RCC clock driver, the real value of HSE
  clock can be used.

_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
  pwrcfg and gpio nodes.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:40:03 -04:00
Patrice Chotard
5fbb2b25ae ARM: DTS: stm32: add stm32h743i-eval files
This file is imported from linux kernel v4.13

Add device tree support for STM32H743 evaluation board.
This board offers :
  _ STM32H743XIH6 microcontroller with 2 Mbytes of
    Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
  _ 5.7” 640x480 TFT color LCD with touch screen
  _ Ethernet compliant with IEEE-802.3-2002
  _ USB OTG HS and FS
  _ I2 C compatible serial interface
  _ RTC with rechargeable backup battery
  _ SAI Audio DAC
  _ ST-MEMS digital microphones
  _ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
  _ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
  _ 1-Gbit Twin Quad-SPI NOR Flash
  _ Potentiometer
  _ 4 colored user LEDs
  _ Reset, wakeup, tamper or key buttons
  _ Joystick with 4-direction control and selector
  _ Board connectors :
     Power jack
     3 USB with Micro-AB
     RS-232 communications
     Ethernet RJ45
     FD-CAN compliant connection
     Stereo headset jack including analog microphone input
     2 audio jacks for external speakers
     microSD™ card
     JTAG/SWD and ETM trace
   _ Expansion connectors:
     Extension connectors and memory connectors for daughterboard
     or wire-wrap board
   _ Flexible power-supply options: ST-LINK USB VBUS or external
     sources
   _ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
     capability: mass storage, virtual COM port and debug port

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:40:03 -04:00
Patrice Chotard
d983a0f008 ARM: DTS: stm32: add stm32h743i-disco files
All these files are imported from linux kernel v4.13

Add device tree support for STM32H743 SoC and discovery
board. This board offers :
  _ STM32H743XIH6 microcontroller with 2 Mbytes of
    Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
  _ 5.7” 640x480 TFT color LCD with touch screen
  _ Ethernet compliant with IEEE-802.3-2002
  _ USB OTG HS
  _ I2 C compatible serial interface
  _ ST-MEMS digital microphones
  _ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
  _ 8Mx32bit SDRAM
  _ 1-Gbit Twin Quad-SPI NOR Flash
  _ Reset, wakeup, or key buttons
  _ Joystick with 4-direction control and selector
  _ Board connectors :
	1 USB with Micro-AB
	Ethernet RJ45
	Stereo headset jack including analog microphone input
	microSD™ card
	RCA connector
	JTAG/SWD and ETM trace
   _ Expansion connectors:
	Arduino Uno compatible Connectors
	2 x PIO connectors (PMOD and PMOD+)
   _ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
     capability: mass storage, virtual COM port and debug port

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:40:02 -04:00
Patrice Chotard
bfd7ef110a ARM: dts: STiH410: update ehci and ohci compatible
Update ehci and ohci node's compatible string in order to
use ehci-generic and ohci-generic drivers.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:39:59 -04:00
Patrice Chotard
01d142850e ARM: dts: STiH410: set DWC3 dual role mode to peripheral
On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:39:59 -04:00
Patrice Chotard
40d1a31e63 usb: dwc3: Add dwc3 glue driver support for STi
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.

Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:39:59 -04:00
Patrice Chotard
9ea2fc88dd ARM: dts: stih410-family: Add missing reset_names for mmc1 node
reset-names property is needed to use the reset
API for STi sdhci driver.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:39:57 -04:00
rick
7b1a50b7b6 nds32: board: Support SPI driver.
Add spi dts node and enable spi dm flash config.

Signed-off-by: rick <rick@andestech.com>
2017-09-21 10:30:22 +08:00
rick
e336b73d8a nds32: ftmac100 support cache enable.
Enable cache and ftmac100 performance can be improved.

Signed-off-by: rick <rick@andestech.com>
2017-09-21 10:30:22 +08:00
rick
19fc21fb4a nds32: bootm: Fix warning of struct tag_serialnr declared
move #include <asm/setup.h> from bootm.c to bootm.h

Signed-off-by: rick <rick@andestech.com>
2017-09-21 10:30:22 +08:00
Tom Rini
e884656c2c Merge git://www.denx.de/git/u-boot-imx 2017-09-20 12:32:34 -04:00
Fabio Estevam
511db3bf5a toradex: imx6: Move g_dnl_bind_fixup() into common SPL code
Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-09-20 15:34:59 +02:00
Tom Rini
975f97b431 Merge git://git.denx.de/u-boot-rockchip 2017-09-18 15:44:57 -04:00
Kever Yang
6e5bd8d6f3 rockchip: ram: rk3399: update reg map for of-platdata
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:38 +02:00
Philipp Tomsich
75ff057851 rockchip: dts: rk3368: reduce the number of nodes seen in TPL
The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes.  This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18 20:40:38 +02:00
Philipp Tomsich
46c89c8efa rockchip: dts: rk3399-puma: replace 'rockchip, vbus-gpio' with fixed regulator
On the RK3399-Q7, we need to turn on the on-module USB hub before using the
USB host interfaces (only the OTG interface is directly connected to the edge
connector).  This drops the deprecated 'rockchip,vbus-gpio' property and uses
a fixed regulator to turn on the USB hub.

References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus"
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18 20:40:37 +02:00
Jagan Teki
d55af074e5 rk3288: Add Vyasa initial board support
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:36 +02:00
Philipp Tomsich
ba1657338b rockchip: rk3399: spl: remove hard-coded addresses for GRF and SGRF
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL
enabled: this allows the use of syscon to retrieve the addresses of
GRF and SGRF (except for the early debug UART setup, which runs so
early that the device-model is not initialised).

This removes the hard-coded addresses and goes through syscon to
retrieve the base-addresses of GRF and SGRF. After that, we use
the structure definitions to locate the respective registers.

In addition to this, the inclusion of header files is also cleaned up:
- all headers are included at the beginning (there was a spurious
  inclusion of the grf header from within a function)
- all #include statements for unused headers are removed
- the remaining #include statements are sorted (while keeping common.h
  included in front)

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18 20:40:36 +02:00
Philipp Tomsich
f041176c46 rockchip: dts: rk3368-lion: add /chosen/tick-timer
To support bootstage recording, we want to mark our DM timer as the
tick-timer; this triggers the support for 'trying harder' to read the
timer in the Rockchip DM timer driver, even if the device model isn't
ready yet.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:36 +02:00
David Wu
4c94aacd62 rockchip: rk322x: Disable integrated macphy for saving power consuming
Unfortunately, the integrated macphy default is enabled, which will
increase power consuming, if we do not use this PHY. So let's disable
it at first, which will save power consuming. If we really use it, then
enable it in driver level.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:33 +02:00
Kever Yang
c964a0dcae rockchip: rk322x: enable fastboot to set boot mode tag
To support fastboot "fastboot reboot-bootloader" cmd.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:32 +02:00
William Wu
809ec9454f ARM: dts: rockchip: add USB nodes for evb-rv1108
This patch adds USB OTG/EHCI/OHCI nodes for evb-rv1108 USB ports.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:32 +02:00
Eric Nelson
8590786acf imx: imx7d: remove CamelCase from ENET_xMHz macros
Update these macros to use all upper-case to avoid checkpatch
warnings:

	ENET_25MHz,
	ENET_50MHz,
	ENET_125MHz,

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-18 17:15:28 +02:00
Stefan Agner
e203dcf23e imx_common: detect USB serial downloader reliably
The current mechanism using SCR/GPR registers work well when
the serial downloader boot mode has been selected explicitly
(either via boot mode pins or using bmode command). However,
in case the system entered boot ROM due to unbootable primary
boot devices (e.g. empty eMMC), the SPL fails to detect that
it has been downloaded through serial loader and tries to
continue booting from eMMC:
  Trying to boot from MMC1
  mmc_load_image_raw_sector: mmc block read error
  SPL: failed to boot from all boot devices
  ### ERROR ### Please RESET the board ###

The only known way to reliably detect USB serial downloader
is by checking the USB PHY receiver block power state...

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2017-09-18 17:15:22 +02:00
Tom Rini
45d19acb2f Merge git://git.denx.de/u-boot-uniphier 2017-09-18 10:58:10 -04:00
Stefan Agner
7d289d6239 imx: add macro to detect whether USB PHY is active
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.

The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2017-09-18 16:51:36 +02:00
Masahiro Yamada
a184fb8e96 ARM: uniphier: add GPU(Mali) reset deassert and clk enable
The driver for Linux is out of control of Socionext, so set up
reset / clock in here.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18 20:26:18 +09:00
Masahiro Yamada
2bf7c86ebb ARM: uniphier: remove bit field macros from sc64-regs.h
Starting from PXs3, the bit fields of  RSTCTRL, CLKCTRL registers
will change every SoC.  There is no more point to define bitfields
in the common header file.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18 20:26:12 +09:00
Masahiro Yamada
81b9bb5fcb ARM: uniphier: merge two defconfig files into uniphier_v7_defconfig
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version.  This is now distinguished by DT.  Merge the two defconfig
files into uniphier_v7_defconfig.

Update the README.uniphier too.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18 20:26:06 +09:00
Heinrich Schuchardt
8a1c44271c x86: ivybridge: remove unused variables
legacy_hole_base_k and legacy_hole_size_k are defined but
not used.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-09-16 14:57:44 +08:00