Commit graph

472 commits

Author SHA1 Message Date
Ilko Iliev
f0a2c7b4b6 at91: add support for the PM9263 board of Ronetix GmbH
The PM9263 board is based on the AT91SAM9263-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16 21:30:48 +02:00
Ulf Samuelsson
cb82a53266 Add support for the AT91RM9200EK Board.
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:20 +02:00
Mike Frysinger
84a9dda324 Blackfin: bf518f-ezbrd: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:46 -04:00
Mike Frysinger
0c31ddf7b7 Blackfin: bf526-ezbrd: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:42 -04:00
Mike Frysinger
5c45f7cac2 Blackfin: bf538f-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:38 -04:00
Mike Frysinger
d9a5d113b9 Blackfin: bf527-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:35 -04:00
Mike Frysinger
76d21803dd Blackfin: bf548-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:29 -04:00
Haiying Wang
765547dc5e MPC85xx: Add MPC8569MDS board support
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-30 13:33:51 -05:00
Wolfgang Denk
aaa0e0812f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-03-26 22:27:45 +01:00
Guennadi Liakhovetski
0c6926736e ARM: Add the imx31_phycore_eet board to MAKEALL
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2009-03-25 22:23:07 +01:00
Nicolas Ferre
df486b1fa3 at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:48:16 +01:00
Grzegorz Bernacki
5c4fa9b474 Add support for the digsy MTC board.
This is the InterControl custom device based on the MPC5200B chip.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-03-20 22:39:14 +01:00
Heiko Schocher
1b6275dfb1 8xx: add support for new keymile kmsupx4 board.
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU

- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18 20:50:05 +01:00
Wolfgang Denk
9eb468da3f Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-19 00:46:32 +01:00
Wolfgang Grandegger
a865bcdac8 MPC85xx: TQM8548: add support for the TQM8548_AG module
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:59 -06:00
Wolfgang Grandegger
ad7ee5d43b MPC85xx: TQM8548: add support for the TQM8548_BE module
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:59 -06:00
Ilya Yanok
0d19f6c8cb qong: support for Dave/DENX QongEVB-LITE board
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-10 00:22:31 +01:00
Wolfgang Denk
6c6e042ab3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-01 21:38:07 +01:00
Dirk Behme
7379f45a7b OMAP3: Add Zoom1 board support
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here:
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:40:16 +01:00
Dirk Behme
2be2c6cc67 OMAP3: Add Pandora support
Add Pandora support.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
ad9bc8e52d OMAP3: Add EVM board
Add EVM board support.

Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
9d0fc8110e OMAP3: Add Overo board
Add Overo board support.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:57 +01:00
Dirk Behme
f904cdbb68 OMAP3: Add common power code, README, and BeagleBoard
Add BeagleBoard support, common power code and README.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-28 21:39:15 +01:00
Wolfgang Denk
49ad480171 Merge branch 'master' of git://git.denx.de/u-boot-mips 2009-01-27 20:55:57 +01:00
Stefan Roese
2a61eff6a8 MIPS: Add VCT board series support (Part 3/3)
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-27 23:08:26 +09:00
Dirk Eibach
89b8619aae ppc4xx: Add GDsys PowerPC 440 ETX board support.
Board support for the Guntermann & Drunck PowerPC 440 ETX module.
Based on the AMCC Yosemite board support by Stefan Roese.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26 10:13:30 +01:00
Alessandro Rubini
d5254f149d Initial support for Nomadik 8815 development board
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.

This is the initial port, with basic infrastructure and
a working serial port.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-24 18:10:37 +01:00
Wolfgang Denk
8f86a3636e Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2009-01-24 02:17:02 +01:00
Wolfgang Denk
1ea0823786 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2009-01-24 02:08:31 +01:00
Graeme Russ
c620c01e96 Added initial eNET board support
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2009-01-24 01:01:16 +01:00
Kim Phillips
833d94bcdc Merge branch 'next' 2009-01-23 17:48:24 -06:00
Heiko Schocher
de0443614a powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-01-24 00:36:19 +01:00
Kumar Gala
18af1c5f0f 85xx: Add a 36-bit physical configuration for MPC8572DS
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23 17:09:18 -06:00
Ron Madrid
5bb907a492 mpc83xx: New board support for SIMPC8313
This patch will create a new board, SIMPC8313, from Sheldon Instruments.  This
board boots from NAND devices and is configureable for either large or small
page devices.  The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support.  The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-23 11:31:18 -06:00
Michal Simek
52a822ed9c microblaze: Rename ml401 to microblaze-generic
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:56 +01:00
Kim Phillips
be4880ebe4 Merge branch 'master' into next 2009-01-21 18:38:51 -06:00
Peter Tyser
78bbc5ce15 XPedite5200 board support
Initial support for Extreme Engineering Solutions XPedite5200 -
a MPC8548-based PMC single board computer.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19 18:18:51 -06:00
Peter Tyser
ccf0fdd02b XPedite5370 board support
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19 18:11:49 -06:00
Michal Simek
8fab49ea91 microblaze: Remove XUPV2P board
---

Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.

This change will go through microblaze custodian tree.
2008-12-10 09:25:33 +01:00
Wolfgang Denk
7fa6a2f3b6 MAKEALL: Automatically use parallel builds
Add logic to the MAKEALL script to determine the number of CPU cores
on the system, and run a parallel build if there is more than one.
Usually this significantrly accelerates builds.

Allow to manually adjust the number of parallel make jobs by using
the "BUILD_NCPUS" environment variable.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-09 00:39:08 +01:00
Heiko Schocher
fed36ac5ae powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-20 15:29:32 -06:00
Wolfgang Denk
23b7b87a37 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-11-09 00:09:51 +01:00
Sergey Lapin
1079432e04 Custom AFEB9260 board support
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2008-11-04 23:47:17 +01:00
TsiChung Liew
536e7dac16 ColdFire: Add MCF5301x CPU and M53017EVB support
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
Georg Schardt
5deb8022c3 ppc4xx: New board avnet fx12 minimodul
This patch adds support for the avnet fx12 minimodul.
It needs the "ppc4xx: Generic architecture for xilinx ppc405"
patch from Ricardo.

Signed-off-by: Georg Schardt <schardt@team-ctech.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-24 17:34:26 +02:00
Dirk Eibach
d7b26d5832 ppc4xx: Add GDSys neo 405EP board support
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:35:02 +02:00
Adam Graham
f09f09d389 ppc4xx: Add AMCC Arches board support (dual 460GT)
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.

Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:34:46 +02:00
Ricardo Ribalda Delgado
e07f4a8033 ppc44x: Unification of virtex5 pp440 boards
This patch provides an unificated way of handling xilinx v5 ppc440 boards.

It unificates 3 different things:

1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.

If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).

2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)

3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.

In order to support new boards they can be implemented in the next way:

a) Simple Generic Board  (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h  and run make xilinx-ppc440-generic_config
&& make

b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile

c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507

Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:

Cheap board by Avnet for evaluating the Virtex5 FX technology.

This patch adds support for:
 - UartLite
 - 16MB Flash
 - 64MB RAM

Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-05 11:51:22 +02:00
Nick Spence
64ac1eb5af mpc83xx: fix mpc8313 in-tree building with NAND
and add mpc8313 NAND build to MAKEALL

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-09-03 16:09:52 -05:00
Wolfgang Denk
a13b2d9379 Merge branch 'master' of git://git.denx.de/u-boot-arm 2008-09-01 00:06:05 +02:00