Commit graph

9462 commits

Author SHA1 Message Date
York Sun
8936691ba6 driver/ddr/fsl: Fix timing_cfg_2
Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
2016-08-02 09:47:34 -07:00
Sumit Garg
7fe1d6a410 crypto/fsl: Update blob cmd to accept 64bit addresses
Update blob cmd to accept 64bit source, key modifier and destination
addresses. Also correct output result print format for fsl specific
implementation of blob cmd.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:39 -07:00
Yunhui Cui
04e5c6d9cc driver: spi: fsl-qspi: remove compile Warnings
Warnins log:
drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’:
drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len);

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:13 -07:00
Tom Rini
26fb8db0f4 Merge git://git.denx.de/u-boot-rockchip 2016-07-31 20:31:13 -04:00
Hans de Goede
4069437dfb net: sun8i_emac: Fix DMA alignment issues with the rx / tx buffers
This fixes the following CACHE warnings when using sun8i_emac:

=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [7bf594a8, 7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [7bf59c90, 7bf59e10]
CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)

Note this commit also changes the max rx size from 2024 to 2044,
matching what the kernel driver uses.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31 21:45:46 +02:00
Chen-Yu Tsai
4694dc56e9 sunxi: gpio: Add .xlate function for gpio phandle resolution
sunxi uses a 2 cell phandle for gpio bindings. Also there are no
seperate nodes for each pin bank.

Add a custom .xlate function to map gpio phandles to the correct
pin bank device. This fixes gpio_request_by_name usage.

Fixes: 7aa9748584 ("dm: sunxi: Modify the GPIO driver to support driver
		      model")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-31 21:45:12 +02:00
John Keeping
2b51784aef rockchip: rk3288: Fix pinctrl for GPIO bank 0
Bank 0 is the "PMU GPIO" bank which is controlled by the PMU registers
rather than the GRF registers.  In the GRF the top half of the register
is used as a mask so that some bits can be updated without affecting the
others, but in the PMU this feature is not provided and the top half of
the register is reserved.

Take the same approach as the Linux driver to update the value via
read-modify-write but setting the mask for only the bits that have
changed.  The PMU registers ignore the top 16 bits so this works for
both GRF and PMU iomux registers.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2016-07-31 07:24:20 -06:00
Kever Yang
46683f3da1 mmc-uclass: correct the device number
Not like the mmc-legacy which the devnum starts from 1, it starts from 0
in mmc-uclass, so the device number should be (devnum + 1) in get_mmc_num().

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-07-31 07:24:20 -06:00
Vignesh R
a6f56ad1ee spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Wenyou Yang
b302669f46 sf: sf_params: Add AT25DF321 flash support
Add AT25DF321 flash support.
Fix AT25DF321A device name.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Vignesh R
fee3b6af90 spi: ti_qspi: Remove delay in read path for dra7xx
As per commit b545a98f5d ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
c595a28530 spi: ti_qspi: Fix compiler warning when DEBUG macro is set
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
69eeefaa06 spi: ti_qspi: Fix failure on multiple READ_ID cmd
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Moritz Fischer
6bde34f1ae spi: Add support for N25Q016A
This commit adds support in the spi-nor driver for the
N25Q016A, a 16Mbit SPI NOR flash from Micron.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Tom Rini
4711e7f7af Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-07-28 08:45:00 -04:00
Tim Harvey
ec21aee653 pci: allow disabling of pci init/enum via env
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-07-28 13:27:17 +02:00
Tom Rini
fe34b6a484 Merge git://git.denx.de/u-boot-dm 2016-07-27 22:30:20 -04:00
Xu Ziyuan
02ebd42cf1 mmc: dw_mmc: reduce timeout detection cycle
It's no need to speed 10 seconds to wait the mmc device out from busy
status. 500 milliseconds enough.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-07-27 20:15:48 -06:00
Stephen Warren
61f5ddcb7a Add a power domain framework/uclass
Many SoCs allow power to be applied to or removed from portions of the SoC
(power domains). This may be used to save power. This API provides the
means to control such power management hardware.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-27 16:29:56 -06:00
Simon Glass
f1a485aa40 dm: socfpga: mmc: Support CONFIG_BLK
Update the driver to support using driver model for block devices.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
329a449f2c dm: mmc: zynq: Convert zynq to use driver model for MMC
Move zynq to the latest driver model support by enabling CONFIG_DM_MMC,
CONFIG_DM_MMC_OPS and CONFIG_BLK.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
dec49e862e dm: zynq: usb: Convert to CONFIG_DM_USB
Convert zynq USB to driver model. Note this is tested on zynq-zybo only.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
fbfa1aba91 net: phy: marvell: Add a missing errno.h header
This corrects a build error on zynqmp.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
911954859d dm: Use dm_scan_fdt_dev() directly where possible
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
2e3f1ff63f dm: Convert users from dm_scan_fdt_node() to dm_scan_fdt_dev()
This new function is more convenient for callers, and handles pre-relocation
situations automatically.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:07 -06:00
Simon Glass
cc7f66f70c dm: core: Add a function to bind child devices
We currently use dm_scan_fdt_node() to bind devices. It is an internal
function and it requires the caller to know whether we are pre- or post-
relocation.

This requirement has become quite common in drivers, so the current function
is not ideal.

Add a new function with fewer arguments, that does not require internal
headers. This can be used directly as a post_bind() method if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:14:37 -06:00
Jaehoon Chung
5628347f59 dm: mmc: dwmmc: use the callback functions as static
There are no places to call these functions.
It should be used the callback function.
Then it can be used as static functions.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:14:37 -06:00
Tom Rini
c6f086ddcb Merge branch 'master' of git://git.denx.de/u-boot-video 2016-07-27 15:22:21 -04:00
Tom Rini
0b6699ad8e Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-07-26 18:33:04 -04:00
Tom Rini
9c7a0a600b Merge git://git.denx.de/u-boot-fsl-qoriq 2016-07-26 17:34:28 -04:00
Chen-Yu Tsai
a85ba87dbe net: sun8i_emac: Drop redundant and incorrect setting of syscon register
In sun8i_emac_board_setup, the driver partially configures the syscon
register for H3 EPHY. However, the settings are incomplete, and
completely unusable. The correct settings are later set in
sun8i_emac_set_syscon, but the incorrect CLK_SEL setting persists.

It is incorrect to use CLK_SEL to select 25 MHz, as the SoC does not
have a 25 MHz clock the EPHY can use.

This patch removes the setting of the syscon register in board_setup,
and also moves set_syscon above mdio_init. While mdio_init does not
access the PHY, it is better to have the PHY parameters setup before
the MDIO bus is registered.

Fixes: a29710c525 ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:03 +02:00
Chen-Yu Tsai
687284483c net: sun8i_emac: Do not configure AHB2 clock
The sun8i_emac driver erroneously configures the AHB2 clock when it
assumes it is configuring the AXI gates, which is not even documented
or ever appeared in either the WiP kernel driver or Allwinner's original
driver.

As a result, AHB2 clock mux is set to an invalid setting, making the
EPHY unusable.

Fixes: a29710c525 ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:02 +02:00
Mingkai Hu
9d3b8bd166 drivers: net/fm: Add Fman support for LS1046A
The Fman module on LS1046A is similiar with that on LS1043A but
LS1046A has one more XFI (10GbE) interface.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:02:32 -07:00
Sumit Garg
7f0a0e4c58 DM: crypto/fsl: Enable rsa DM driver usage before relocation
Enable rsa signature verification in SPL framework before relocation for
verification of main u-boot.

Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:01:21 -07:00
mario.six@gdsys.cc
27059c3e4d i2c: fsl: Fix driver initialization
Due to a oversight in testing, the initialization of the recently
introduced Freescale I2C DM driver works only for 36 bit mode of e.g.
the MPC85XX SoCs (specifically, if the physical addresses are 64 bit
wide and the DT addresses 32 bit wide).

This patch corrects the initialization so that it will work in a more
general setting.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:00:44 -07:00
Tom Rini
c3c9fd31ba Merge branch 'master' of git://git.denx.de/u-boot-i2c 2016-07-26 08:29:30 -04:00
mario.six@gdsys.cc
6e677caf8c i2c: mvtwsi: Add documentation
Add full documentation to all driver functions.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:20:38 +02:00
mario.six@gdsys.cc
c68c624320 i2c: mvtwsi: Make delay times frequency-dependent
Some devices using the MVTWSI driver have the option to run at speeds
faster than Standard Mode (100kHZ). On the Armada 38x controllers, this
is actually necessary, since due to erratum FE-8471889, a timing
violation concerning repeated starts prevents the controller from
working correctly in Standard Mode. One of the workarounds recommended
in the erratum is to set the bus to Fast Mode (400kHZ) operation and
ensure all connected devices are set to Fast Mode.

In the current version of the driver, however, the delay times are
hard-coded to 10ms, corresponding to Standard Mode operation. To take
full advantage of the faster modes, we would need to either keep the
currently configured I2C speed in a globally accessible variable, or
pass it to the necessary functions as a parameter. For DM, the first
option is not a problem, and we can simply keep the speed in the private
data of the driver. For the legacy interface, however, we would need to
introduce a static variable, which would cause problems with boots from
NOR flashes; see commit d6b7757 "i2c: mvtwsi: Eliminate
twsi_control_flags."

As to not clutter the interface with yet another parameter, we therefore
keep the default 10ms delays for the legacy functions.

In DM mode, we make the delay time dependant on the frequency to allow
taking full advantage of faster modes of operation (tested with up to
1MHZ frequency on Armada MV88F6820).

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:20:28 +02:00
mario.six@gdsys.cc
24f9c6bbc7 i2c: mvtwsi: Handle zero-length offsets properly
Zero-length offsets are not properly handled by the driver. When a read
operation with a zero-length offset is started, a START condition is
asserted, and since no offset bytes are transferred, a repeated START is
issued immediately after, which confuses the controller.

To fix this, we send the first START only if any address bytes need to
be sent, and keep track of the expected start status accordingly.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:20:19 +02:00
mario.six@gdsys.cc
14a6ff2c4f i2c: mvtwsi: Add compatibility to DM
This patch adds the necessary functions and Kconfig entry to make the
MVTWSI I2C driver compatible with the driver model.

A possible device tree entry might look like this:

i2c@11100 {
	compatible = "marvell,mv64xxx-i2c";
	reg = <0x11000 0x20>;
	clock-frequency = <100000>;
	u-boot,i2c-slave-addr = <0x0>;
};

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:20:13 +02:00
mario.six@gdsys.cc
f8a10ed1fd i2c: mvtwsi: Make address length variable
The length of the address parameter of the __twsi_i2c_read and
__twsi_i2c_write functions is fixed to four bytes.

As a final step in the preparation of the DM conversion, we make the
length of this parameter variable by turning it into an array of bytes,
and convert the 32 bit value that's passed to the legacy functions into
a four-byte-array on the fly.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:20:05 +02:00
mario.six@gdsys.cc
3c4db636ac i2c: mvtwsi: Factor out adap parameter
To be able to use the compatibility layer from the DM functions, we
factor the adap parameter out of all functions, and pass the actual
register base instead.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:56 +02:00
mario.six@gdsys.cc
61bc02b260 i2c: mvtwsi: Add compatibility functions
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:49 +02:00
mario.six@gdsys.cc
e075828128 i2c: mvtwsi: Use 'uint' instead of 'unsigned int'
Since some additional parameters will be added in the course of this
patch series (especially with the addition of DM support), we replace
the longer "unsigned int" declarations with "uint" declarations to keep
the parameter lists more readable.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:42 +02:00
mario.six@gdsys.cc
059fce9f61 i2c: mvtwsi: Get rid of status parameter
The twsi_stop function contains a parameter "status," which is used to
pass in the current exit status of the function calling twsi_stop, and
either return this status unchanged if it indicates an error, or return
twsi_stop's exit status if it does not indicate an error.

While not massively complicated, this adds another purpose to the
twsi_stop function, which should have the sole purpose of asserting a
STOP condition on the bus (and not manage the exit status of its
caller).

Therefore, we move the exit status management into the caller functions
by introducing a "stop_status" variable and returning either the status
before the twsi_stop call (kept in the "status" variable), or the status
from the twsi_stop call, depending on which indicates an error.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:35 +02:00
mario.six@gdsys.cc
670514f524 i2c: mvtwsi: Eliminate flags parameter
Due to breaking boots from NOR flashes, commit d6b7757 ("i2c: mvtwsi:
Eliminate twsi_control_flags") removed the static global
twsi_control_flags variable, which kept a set of default flags that were
always or'd to the control register when writing. It was replaced with a
flags parameter, which was passed around between the functions that
needed it.

Since the twsi_control_flags variable was used just for the purposes of
a) setting the MVTWSI_CONTROL_TWSIEN on every control register write,
   and
b) setting the MVTWSI_CONTROL_ACK from twsi_i2c_read if needed,
anyway, the added overhead of another variable being passed around is no
longer justified, and we are better off implementing this flag setting
logic locally in the functions that actually write to the control
register.

Therefore, this patch sets MVTWSI_CONTROL_TWSIEN on every control
register write, replaces the twsi_i2c_read's flags parameter with a
ack_flag parameter, which tells the function whether to acknowledge the
read or not, and removes every other instance of the flags variable.
This has the added benefit that now every notion of "global default
flags" is gone, and it's much easier to see which control flags are
actually set at which point in time.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:29 +02:00
mario.six@gdsys.cc
49c801bf35 i2c: mvtwsi: Improve and fix comments
This patch fixes only comments/documentation: Streamline capitalization
and improve grammar/punctuation.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:23 +02:00
mario.six@gdsys.cc
dfc3958cd3 i2c: mvtwsi: Streamline code and add documentation
Convert groups of logically connected preprocessor defines into proper
enums, one macro into an inline function, and add documentation
to/extend existing documentation of these items.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:16 +02:00
mario.six@gdsys.cc
9ec43b0c3f i2c: mvtwsi: Fix style violations
This patch fixes seven style violations: Six superfluous spaces after
casts, and one logical continuation violation.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-26 10:19:06 +02:00
Mugunthan V N
daa69ffe3d drivers: i2c: omap24xx_i2c: adopt omap_i2c driver to driver model
Convert omap i2c driver to adopt i2c driver model

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-26 08:40:09 +02:00