Upper-bound for iterating for-loop over register set entries is incorrect.
Fix it byt calculating correct number of entries.
And fix also dumping the last entry DATA_DELAY, which is the last and not
first (zero).
Fixes: 1a8e6b63e2 ("tools: kwbimage: Dump kwbimage config file on '-p -1' option")
Signed-off-by: Pali Rohár <pali@kernel.org>
Show image type and version during parsing of kwbimage.
And show reasons in error messages when parsing failed.
This can help to debug issues with invalid images.
Signed-off-by: Pali Rohár <pali@kernel.org>
Marvell BootROM interprets execaddr of SPI/NOR XIP images as relative byte
offset from the from the beginning of the flash device. So if data image
offset and execute offset are not same then it is needed to adjust them
also in DDR RAM.
Fixes: f2c644e0b8 ("tools: kwboot: Patch destination address to DDR area for SPI image")
Signed-off-by: Pali Rohár <pali@kernel.org>
Some NOR images may be execute-in-place and do not contain DDR init code in
its kwbimage header. Such images cannot be booted over UART as BootROM
loads them to RAM. Add check that kwbimage contains DDR init code in its
header (either as binary code header or as the simple register-value set).
In some cases it is possible to load very small image into L2SRAM and when
DDR init code is not required. So check for L2SRAM load address and skip
DDR init code check in this case.
Signed-off-by: Pali Rohár <pali@kernel.org>
Before starting parsing of kwbimage, first validate that all optional v1
headers and correct. This prevents kwboot crashes on invalid input.
Signed-off-by: Pali Rohár <pali@kernel.org>
The 32-bit data checksum in UART image is not checked by the BootROM and
also Marvell tools do not generate it.
So if data checksum stored in UART image does not match calculated checksum
from the image then treat those checksum bytes as part of the executable
image code (and not as the checksum) and for compatibility with the rest of
the code manually insert data checksum into the in-memory image after the
executable code, without overwriting it.
This should allow to boot UART images generated by Marvell tools.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add information of all available image types and where they should be
stored. Storage location offsets where documented from the disassembly of
the A385 BootROM image dump.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add reference to Avanta Boot Flow documentation, BobCat2, AlleyCat3 and
PONCat3 BootROM Firmware documentation and links to public Marvell tools:
hdrparser.c and doimage.c
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
To parse SATA kwbimage in the same way as Marvell BootROM, it is needed to
interpret srcaddr as relative offset to the main header. This change fixes
loading of SATA images via kwboot over UART.
Fixes: 792e423550 ("tools: kwboot: Patch source address in image header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
The main header is stored at absolute sector number 1. So do not add or
subtract it when calculating with relative offsets to the main header.
Fixes: 501a54a29c ("tools: kwbimage: Fix generation of SATA, SDIO and PCIe images")
Fixes: 5c61710c98 ("tools: kwbimage: Properly set srcaddr in kwbimage v0")
Fixes: e0c243c398 ("tools: kwbimage: Validate data checksum of v1 images")
Fixes: aa6943ca31 ("kwbimage: Add support for extracting images via dumpimage tool")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To parse SDIO kwbimage in the same way as Marvell BootROM, it is needed to
interpret srcaddr in bytes. This change fixes loading of SDIO images via
kwboot over UART.
Fixes: 792e423550 ("tools: kwboot: Patch source address in image header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To generate SDIO kwbimage compatible with Marvell BootROM, it is needed to
have srcaddr in bytes. This change fixes SDIO images for Armada 38x SoCs.
Fixes: 501a54a29c ("tools: kwbimage: Fix generation of SATA, SDIO and PCIe images")
Fixes: 5c61710c98 ("tools: kwbimage: Properly set srcaddr in kwbimage v0")
Fixes: e0c243c398 ("tools: kwbimage: Validate data checksum of v1 images")
Fixes: aa6943ca31 ("kwbimage: Add support for extracting images via dumpimage tool")
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support for rk3588 package header in mkimage tool.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using the mkimage entry with the multiple-data-files prop and having a
missing external blob result in an unexpected ValueError exception using
the --allow-missing flag.
ValueError: Filename 'missing.bin' not found in input path (...)
Fix this by using _pathname that is resolved by ObtainContents for blob
entries, ObtainContents also handles allow missing for external blobs.
Mark mkimage entry as missing and return without running mkimage when
missing entries is reported by CheckMissing.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current init size limit of 76KiB is too big to fit in the 64KiB SRAM
on RK3568, sync init size limit from vendor u-boot to fix this.
Set init size limit to 60KiB (-16KiB) for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Latest vendor TPL for RK3328 has grown past the current init size limit
of 28KiB, sync the init size limit from vendor u-boot to fix this.
Set init size limit to 30KiB (+2KiB) for RK3328.
This makes it possible to use latest vendor TPL on RK3328 without
getting a size limit error running the mkimage command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rockchip-tpl entry can be used when an external TPL binary should be
used instead of the normal U-Boot TPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
I had added this line locally, rebuild the image, but didn't ensure that
I had committed the correct version of the patch as well.
Fixes: 75b031ee4a ("Dockerfile: download binaries for Nokia RX-51")
Signed-off-by: Tom Rini <trini@konsulko.com>
Downloading files for a test may fail if the server is offline.
It is preferable to provide the files in our Docker image.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the 'missing-msg' for more detailed output
on missing system firmware.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
At present we show 'main section' as the top-level section name. It may
be more helpful to show the actual image name. This is tricky because
Image is a parent class of Entry_section, so there is no distinction
between an image and a section.
Update it to show the image name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Build trace-cmd as part of the docker image, so that trace tests can be
used. Unfortunately the version provided by distributions is a little old
and has bugs. It also does not support specifying the time base for the
trace, which is required to convert microseconds to nanaseconds.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a second variant of the flame graph that shows records in terms of the
number of microseconds used by each call stack. This is a useful way of
seeing where time is going within the execution of U-Boot.
This requires a call stack that records the start time of each function,
as well as a way of subtracting all time consumed by child functions, so
that this time is not counted twice by the flamegraph. The time values in
the output are just for the function itself, not for its children.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to see how many times each function is called, particularly
in the context of its callers. A flamegraph is a way of showing this.
Support output in this format which can be used by the flamegraph.pl
script, to generate an SVG image for browsing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for writing ftrace records in the 'funcgraph' format, which
shows function entry and exit points as well as the time taken by each
function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the information in the trace header instead of reading it from the
trace records. Add debugging to check that System.map and the trace header
agree on this value.
Signed-off-by: Simon Glass <sjg@chromium.org>
The old text format is not much used anymore. Instead a new trace-cmd tool
has introduced a binary format for trace records.
Add support for generating this format. This involves removing the old
text format, adding various helpers for the new format and adjusting the
code to use an output file instead of stdout.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current use of 'profile' in some places is confusing. Update the code
to use the word 'trace' consistently. Change the flags to better match
their meaning and add some more comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
The readme file for buildman is called buildman.rst.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is very old and does not appear to be used. The CONFIG option
enabling it is no-longer present. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems to have been used by ppc4xx which was removed a while back.
The Kconfig does not exist so it is never built. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not a Kconfig option so we should not be setting it in the
Makefile. Rename it to use a CFS_ prefix, since this is still used in
mxsimage.c
In general tools should support all the features without reference to
CONFIG options, but this is left to the maintainer to look at.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes the Makefile rules or source code refers to Kconfig options
which don't exist. Update the moveconfig tool to check this and produce
a series of reports about inconsistencies.
This can then be used to generate patches to correct the problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
If image file is stored on flash partition then it contains padding, which
is not part of the image itself. Image data size is stored in the image
header. So use image size from the header instead of expecting that total
image file size is size of the header plus size of the image data. This
allows dumpimage to parse image files with padding (e.g. dumped from flash
partition).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before reading image header, verify that image size is at least size of
the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpimage type requires only that two first 32-bit words of data file are
non-zero. So basically every random data file can be guessed and verified
as gpimage. So completely skip gpimage type from image autodetection code
to prevent lot of false positive results. Data file with gpimage type can
be still verified and parsed by explicitly specifying -T gpimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The default splashfile name saved is ti.gz. User can use these
logo files and use it to test splash screen.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
The handle "fd" was created in imx8image.c:249 by calling the "fopen"
function and is lost in imx8image.c:282.
Should close the 'fd' file descriptor before exiting the
parse_cfg_file(image_t *param_stack, char *name) function.
Fixes: a2b96ece5b ("tools: add i.MX8/8X image support")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The handle "fd" was created in imx8mimage.c:178 by calling
the "fopen" function and is lost in imx8mimage.c:210.
Should close the 'fd' file descriptor before exiting
the parse_cfg_file(char *name) function.
Fixes: 6609c2663c ("tools: add i.MX8M image support")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
The struct dcd_v1_t is initialized to MAX_HW_CFG_SIZE_V1 (60)
structs 'dcd_type_addr_data_t', so the indexes to use on its elements
are [0,59]. But on line 478, the variable 'length' can take on the value
60, which applies to array overflow: cd_v1->addr_data[length].type Thus,
it is necessary to tighten the check on the 'size' variable on line 463.
Fixes: 0b0c6af387 ("Prepare v2020.01")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Extend support for signing in auto-generated (-f auto) FIT. Previously,
it was possible to get signed 'images' subnodes in the FIT using
options -g and -o together with -f auto. This patch allows signing
'configurations' subnodes instead of 'images' ones (which are hashed),
using option -f auto-conf instead of -f auto. Adding also -K <dtb> and
-r options, will add public key to <dtb> file with required = "conf"
property.
Summary:
-f auto => FIT with crc32 images
-f auto -g ... -o ... => FIT with signed images
-f auto-conf -g ... -o ... => FIT with sha1 images and signed confs
Example: FIT with kernel, two device tree files, and signed
configurations; public key (needed to verify signatures) is
added to u-boot.dtb with required = "conf" property.
mkimage -f auto-conf -A arm -O linux -T kernel -C none -a 43e00000 \
-e 0 -d vmlinuz -b /path/to/first.dtb -b /path/to/second.dtb \
-k /folder/with/key-files -g keyname -o sha256,rsa4096 \
-K u-boot.dtb -r kernel.itb
Example: Add public key with required = "conf" property to u-boot.dtb
without needing to sign anything. This will also create a useless FIT
named unused.itb.
mkimage -f auto-conf -d /dev/null -k /folder/with/key-files \
-g keyname -o sha256,rsa4096 -K u-boot.dtb -r unused.itb
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On a second and third look, a recent patch seems to be writing to the
wrong place - updating offsets from the address of the pointer instead
of what the pointer points to.
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 2d1b2ac13f ("tool: ifwitool: Fix buffer overflow")
Acked-by: Sean Anderson <seanga2@gmail.com>
Unfortunately a recent patch snuck through without the require test
coverage. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 571bc4e67d ("binman: Support positioning an entry by and ELF symbol")
This property sets the minimum size of an entry, including padding but
not alignment. It can be used to reserve space for growth of an entry,
or to enforce a minimum offset for later entries in the section.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In some cases it is desired for SPL to start TF-A instead of U-Boot
proper. Add support for a new property fit,firmware that picks a
valid entry and prepends the remaining valid entries to the
loadables list generated by the split-elf generator.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Special nodes, hash and signature, is not being added to the nodes
generated for each segment in split-elf operation.
Copy the subnode logic used in _gen_fdt_nodes to _gen_split_elf to
ensure special nodes are added to the generated nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to indicate what alignment to use for the FIT and its
external data. Pass the alignment to mkimage via the -B flag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes it possible to run the patman test suite simply by invoking
'pytest' from the patman sub-directory:
$ cd tools/patman
$ pytest
Otherwise, the top level .checkpatch.conf would be ignored and
multiple test_checkpatch.py tests would fail.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 648d8186dd, because
it broke usage of patman on Linux, whose check script doesn't know
about '--strict' or '--u-boot'.
Reported-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Sjoerd Simons <sjoerd@collabora.com>
In some cases it is useful to position an entry over the top of a symbol
in an ELF file. For example, if the symbol holds a version string then it
allows the string to be accessed from the fdtmap.
Add support for this.
Suggested-by: Pali Rohár <pali@kernel.org>
Suggested-by: Keith Short <keithshort@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current support for updating variables in a binary is hard-coded to
work with U-Boot:
- It assumes the image starts at __image_copy_start
- It uses the existing U-Boot-specific entry types
It is useful for other projects to use these feature.
Add properties to enable writing symbols for any blob, a way of specifying
the base symbol and a way of providing the ELF filename to allow symbol
lookup to take place.
With this it is possible to update a Zephyr image, such as zephyr.bin
after it has been built.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to have an entry overlap with another in a
section, either to update the contents within a blob, or to add an entry
to the fdtmap that covers only part of the blob.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to define an entry which does not have its own
contents but does appear in the image. The contents are set by the section
which contains it, even though it appears as an entry in the fdtmap.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some blobs are actually not necessary for the board to work correctly. Add
a property to allow this to be indicated. Missing optional blobs do not
cause a build failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
OP-TEE has a format with a binary header that can be used instead of the
ELF file. With newer versions of OP-TEE this may be required on some
platforms.
Add support for this in binman. First, add a method to obtain the ELF
sections from an entry, then use that in the FIT support. We then end up
with the ability to support both types of OP-TEE files, depending on which
one is passed in with the entry argument (TEE=xxx in the U-Boot build).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which checks whether data is in ELF format or not. This
will be used by binman to check this for entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support entries which can be optional depending on their contents. This
allows special entry types which appear in the image only when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Several etypes have this reference in their documentation. Now that we are
using rST, link to the section directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
At present only the image (which is a section) has a filename. Move this
implementation to the entry_Section class so that any section can have a
filename. With this, the section data is written to a file.
This allows parts of an image to be written, along with the entire image.
Make a note that this can be used to include the contents of a section in
one image in another (later) image.
Signed-off-by: Simon Glass <sjg@chromium.org>
This now includes flags and the layout has changed slightly in recent
versions of Linux. Update the generator accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
The flags in this tool don't match the comments or help. Also the variable
names are quite confusing. Update them for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add messages to make it clearer which part of the FIT creation is failing.
This can happen when an invalid 'algo' property is provided in the .its
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for rv1126 package header in mkimage tool.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is read-only data, so mark it as such.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update to the latest "jammy" tag. This requires us to list libc6-i386 as
a required package to install (for nokia_rx51 tests) that was previously
implicit.
Signed-off-by: Tom Rini <trini@konsulko.com>
In preparation of adding the infodocs target to our CI install the
prerequisite texinfo software package.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This makes it possible to configure a project to use some other
location or script than the default scripts/get_maintainer.pl one used
in the U-Boot and Linux projects. It can be configured via a .patman
configuration file and accepts arguments, as documented.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
This enables versioning a project specific patman configuration file.
It also makes it possible to declare the project name, which is not a
useful thing to do in $HOME/.patman. A new test is added, along
updated documentation.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rationale: if the user explicitly provide this argument, they probably
intend for it to be used.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This better matches Python conventions, allowing to easily test
whether the optional argument is provided.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of propagating it from the module entry point (main script).
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SafeConfigParser class has been renamed in Python 3.2 to
ConfigParser, and the old alias has been deprecated since.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove extraneous imports, variables and comply to PEP 8 maximum line
width, among other PEP 8 changes suggested by Pyflake.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Document that this command is the default and what it's intended for.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Pytest offers useful features such as selecting tests by means of a
regular expression, or running the pdb debugger upon encountering a
test failure.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Some tests would fail when the test data is not available, so it
doesn't make much sense to expose the action when patman is running
outside of the u-boot git checkout.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
With this change, a user can run the patman test suite using Pytest
the same as when using 'patman test':
$ cd tools/patman && pytest
[...]
44 passed, 8 warnings in 8.87s
$ ./patman test
Ran 44 tests in 8.460s
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
This allows running the package as a Python module, like e.g.:
$ python -m patman
It also prevents Pytest from attempting to parse main.py, which
would cause errors.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Fix up main.py in __init__.py:
Signed-off-by: Simon Glass <sjg@chromium.org>
This resolves 10 out of 11 test failures seen when running './patman
test' from the 'tools/patman' subdirectory. This was caused by the
.checkpatch.conf configuration file at the root of the project not
being picked up. Make the test suite of patman independent from it by
always invoking the checkpatch.pl script with the minimally required
arguments for the test suite to pass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Previously it would rely on the executing script location, which could
break for example when running the tests via 'pytest'.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
This patch fixes all the PEP 8 warnings reported by Pyflake for the
gitutil module.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Rationale: this is more robust than assumptions about the file
hierarchy layout of the installation of patman, for example on non
file-hierarchy standard (FHS) systems such as Guix System or Nix OS.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes a regression introduced in commit 74df491051 ("buildman:
Convert documentation to rST").
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
distutils is about to meet its demise [1]. Switch to setuptools.
[1] https://peps.python.org/pep-0632/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point all listed adhoc CONFIG symbols have been migrated to
Kconfig or removed from the tree or renamed to CFG (or similar). We also
now have CI tests that will error on any new introductions, and
checkpatch.pl also looks. We can now remove these hooks and related
scripts.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all CONFIG symbols are in Kconfig, checkpatch.pl should check
for and error on any case of define/undef CONFIG_*.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Drop CONFIG_BUILD_ENVCRC as this is never set directly but instead
means ENV_IS_EMBEDDED, so reference that in code and rename the Makefile
usage to BUILD_ENVCRC.
- Remove extra-$(CONFIG_ENV_IS_EMBEDDED) line as it could never be true,
and likely why there is an extra- line for CONFIG_ENV_IS_IN_FLASH (the
only use case today of embedded environments).
- With these slight changes we can then see that using the calculated
symbol of ENV_IS_EMBEDDED is the right thing to use in any code which
needs to know this situation and can remove CONFIG_ENV_IS_EMBEDDED
entirely.
Signed-off-by: Tom Rini <trini@konsulko.com>
With LTO enabled the U-Boot initial environment is no longer stored
in an easy accessible section in env/common.o. I.e. the section name
changes from build to build, its content maybe compressed and it is
annotated with additional data.
Drop trying to read the initial env with elf tools from the compiler
specific object file in favour of adding and using a host tool with
the only functionality of printing the initial env to stdout.
See also:
https://lore.kernel.org/all/927b122e-1f62-e790-f5ca-30bae4332c77@foss.st.com/
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the user select the image type "flat_dt" a FIT image will be build.
This breaks the legacy use case of putting a Flat Device Tree into a
legacy u-boot image.
Add a new image type "fdt_legacy" to build a legacy u-boot image
with a "flat_dt" type.
Link: https://lore.kernel.org/all/20221028155205.ojw6tcso2fofgnhm@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
In case there's no struct image_type_params::set_header callback, no
"errno" will be set. Don't fail with an error message, followed by
"Success". Remove the printing of the human readable "errno" value.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The handle "fd" was created in fdtgrep.c:708 by calling the
"open" function and is lost in fdtgrep.c:716 and fdtgrep.c:723.
Close file descriptor 'fd' before exiting with an error from function
utilfdt_read_err_len(const char *filename, char **buffp, off_t *len).
Fixes: 1043d0a029 ("fdt: Add fdtgrep tool")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The copy_datafile(ifd, params.datafile) function has been
implemented to copy data by reducing the number of lines in the main
function.
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
An incorrect 1st parameter is passed to the fix_member()
function. Should use a pointer to the beginning of the parent structure
(bpdt or subpart_dir, because are boxed), not to their fields. Otherwise,
this leads to an overrun of the structure boundary, since in the
fix_member() function, an 'offset' is made, relative to the 1st argument,
which itself is an 'offset' from the beginning of the structure.
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This will cause the local_time pointer is passed as the 4th argument
to function strftime() to also point to NULL. This result in a
segmentation fault. Thus, it's necessary to add a check of the local_time
pointer to NULL.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Update to gcc-12.2, and cherry-pick a fix in grub for risc-v
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the toolchain list to be first 12.2.0 and second 11.1.0 and
that's it.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This header was already included just above version.h,
do not include it twice.
Fixes: 3db7110857 ("crc32: Use the crc.h header for crc functions")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new flag to buildman so that we will in turn pass
BINMAN_ALLOW_MISSING=1 to 'make'. Make use of this flag in CI.
Allow the settings file to control this.
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This was dropped my mistake. Reinstate it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: d829f1217c ("bulidman: Add support for a simple build")
These are documented in various several sections. Add a new section that
mentions them all in one place so it is easier to see what environment
variables can be used to control U-Boot's use of binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Buildman should consider a build as a success (with warnings) if missing
blobs have been dealt with by binman, even though buildman itself returns
and error code overall. This is how other warnings are dealt with.
We cannot easily access the 103 exit code, so detect the problem in the
output.
With this change, missing blobs result in an exit code of 101, although
they still indicate failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support for some architectures has been removed since buildman was first
written. Also all toolchains are now available at kernel.org so we don't
need the links, except for arc where the kernel.org toolchain fails to
build all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
The settings file omits a few lines which are useful for getting every
board building. Add these and update the documentation tool.
Signed-off-by: Simon Glass <sjg@chromium.org>
This script was removed about 6 years ago so most people should be aware
that it is not needed anymore. Drop mention of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert the buildman documentation to rST format and include it in the
'build' section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <foss+uboot@0leil.net>
At present binman returns success when told to handle missing/faked blobs
or missing bintools. This is confusing since in fact the resulting image
cannot work.
Use exit code 103 to signal this problem, with a -W option to convert
it to a warning.
Rename the flag to --ignore-missing since it controls bintools also.
Add documentation about exit codes while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit daa2da754a.
This commit is not needed anymore since the btool_ prefix is
automatically stripped by bintool.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The binary is looked on the system by the suffix of the packer class.
This means binman was looking for btool_gzip on the system and not gzip.
Since a btool can have its btool_ prefix missing but its module and
binary presence on the system appropriately found, there's no need to
actually keep this prefix after listing all possible btools, so let's
remove it.
This fixes gzip btool by letting Bintool.find_bintool_class handle the
missing prefix and still return the correct class which is then init
with gzip name instead of btool_gzip.
Additionally, there was an issue with the cached module global variable.
The variable only stores the module and not the associated class name
when calling find_bintool_class.
This means that when caching the module on the first call to
find_bintool_class, class_name would be set to Bintoolbtool_gzip but the
module_name gzip only, adding the module in the gzip key in the module
dictionary. When hitting the cache on next calls, the gzip key would be
found, so its value (the module) is used. However the default class_name
(Bintoolgzip) is used, failing the getattr call.
Instead, let's enforce the same class name: Bintool<packer>, whatever
the filename it is contained in.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for setting OEM flags in the capsule header. As per the
UEFI specification, bits 0-15 of the flags member of the capsule
header can be defined per capsule GUID.
The oemflags will be used for the FWU Multi Bank update feature, as
specified by the Dependable Boot specification[1]. Bit
15 of the flags member will be used to determine if the
acceptance/rejection of the updated images is to be done by the
firmware or an external component like the OS.
[1] - https://git.codelinaro.org/linaro/dependable-boot/mbfw/uploads/6f7ddfe3be24e18d4319e108a758d02e/mbfw.pdf
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The Dependable Boot specification[1] describes the structure of the
firmware accept and revert capsules. These are empty capsules which
are used for signalling the acceptance or rejection of the updated
firmware by the OS. Add support for generating these empty capsules.
[1] - https://git.codelinaro.org/linaro/dependable-boot/mbfw/uploads/6f7ddfe3be24e18d4319e108a758d02e/mbfw.pdf
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Add test cases for accessing the FWU Metadata on the sandbox
platform. The sandbox platform also uses the metadata access driver
for GPT partitioned block devices.
The FWU feature will be tested on the sandbox64 variant with a raw
capsule. Remove the FIT capsule testing from sandbox64 defconfig --
the FIT capsule test will be run on the sandbox_flattree variant.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In some cases the ELF version of SPL builds may be packaged, rather
than a binary .bin file. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is used by several etypes and we plan to add more that use
it. Make symbol writing a feature of the base class to reduce the code
duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is needed for some soon-to-be-applied patches. Scan the configs/
directory to see if any of the files match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com>
Suggested-by: Tom Rini <trini@konsulko.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
Adding support to symlink an image packaged using binman.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Just like we exclude data-size, data-position, and data-offset from
fit_config_check_sig, we must exclude them while signing as well.
While we're at it, use the FIT_DATA_* defines for fit_config_check_sig
as welll.
Fixes: 8edecd3110 ("fit: Fix verification of images with external data")
Fixes: c522949a29 ("rsa: sig: fix config signature check for fit with padding")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Binman needs this module to build sandbox_vpl and it is needed elsewhere
in CI.
Add it to the docker file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xpyron.glpk@gmx.de>
Putting these definitions in a header will allow signatures to be
validated independently of bootm.
Signed-off-by: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
riscv32 needs a different toolchain than riscv64
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
For building riscv32 targets we should use the riscv32 toolchain.
Add it to the Docker image.
Drop the riscv toolchain-alias as we do not need it in future.
While in here, update to the latest "jammy" tag.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
[trini: Update to latest jammy tag]
Signed-off-by: Tom Rini <trini@konsulko.com>
