Implement a ARM SMCCC based driver that allow to use
a secure watchdog on the platform.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ftwdt010 watchdog driver was deleted by
commit 11232139e3 ("nds32: Remove the architecture")
Return it to the codebase in a DM compatible form. Enable it in
sandbox_defconfig to test compilability.
Another platform using ftwdt010 will be submitted later.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver supports the bcm2835 watchdog found on
Raspberry Pi boards.
It is derived from the Linux driver and was tested
on two Raspberry Pi board versions (B+ and 3B+).
Signed-off-by: Etienne Dublé <etienne.duble@imag.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----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=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
Enable Renesas RSwitch driver, matching SERDES PHY driver and Marvell
10G ethernet PHY driver in R8A779F0 S4 Spider board configuration to
make ethernet available via the RSwitch ports.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current shell prompt '->' interferes with CI matching on 'bdinfo'
output. When CI test.py attempts to locate memory information in the
'bdinfo' output, it matches on '->' prefix which is identical to the
shell prefix. Switch the prompt to default '=>' one to avoid this
interference.
Suggested-by: Tom Rini <trini@konsulko.com> # found the CI oddity
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This patch adds Ethernet Switch support that found on R-Car S4
(r8a779f0) SoC. This is extracted from multiple patches from
downstream BSP, with additional rework of the network device
registration.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Marek: Rework the driver to support all ports via subdrivers.
Split the driver up, add generic PHY framework support.
Generic code clean ups.]
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add Renesas Ethernet SERDES driver for R-Car S4-8 (r8a779f0).
The datasheet describes initialization procedure without any information
about registers' name/bits. So, this is all black magic to initialize
the hardware. Especially, all channels should be initialized at once.
This driver is imported and adjusted from Linux 6.3-rc1 commit:
50133cd3e8dd1 ("phy: renesas: r8a779f0-eth-serdes: Remove retry code in .init()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use IS_ENABLED() instead of CONFIG_IS_ENABLED() to check for CONFIG_
option which is identical across all of U-Boot and xPL builds.
Fixes: 2769ddc99f ("mmc: tmio: Replace ifdeffery with IS_ENABLED/CONFIG_IS_ENABLED macros")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
octeontx_bch_devices and octeontx_pci_nand_deferred_devices are only
referenced in the files where they are defined. Make them static.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230405143837.785082-1-bmeng@tinylab.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add support for the iproc Broadcom NAND controller,
used in Northstar SoCs for example. Based on the Linux
driver.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308214231.378013-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
nand-ecc-algo = "bch";
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308212851.370939-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
As there are other types of NAND flashes like SPI NAND, let's be
more specific.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230213094626.50957-2-frieder@fris.de/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In [1] Michael agreed on taking patches for SPI NAND through the RAW
NAND tree. Add a dedicated entry to the MAINTAINERS file which adds
Michael and Dario as maintainers and myself as reviewer.
[1] https://lists.denx.de/pipermail/u-boot/2023-February/508571.html
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/all/20230213094626.50957-1-frieder@fris.de/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add m68k M5208EVBE machine configured to test U-Boot m68k support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add M5208EVBE board to CI. This does not use default config due to
limitations of QEMU emulation, instead the timer is switched from
DMA timer to PIT timer and RAMBAR accesses are inhibited.
Local QEMU launch command is as follows:
$ qemu-system-m68k -nographic -machine mcf5208evb -cpu m5208 -bios u-boot.bin
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
The QEMU emulation of m68k does not support RAMBAR accesses,
add Kconfig option which inhibits those accesses, so that
U-Boot can be started in m68k QEMU for CI testing purpopses
until QEMU emulation improves.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The QEMU emulation of m68k does not support DMA timer, the only
timer that is supported is the PIT timer. Implement trivial PIT
timer support for m68k.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
There is an existing CONFIG_MCFTMR Kconfig symbol,
use it and drop all other instances of CFG_MCFTMR.
This duality is likely a result of bogus conversion
to Kconfig.
Fixes: 7ff7b46e6c ("m68k: rename CONFIG_MCFTMR to CFG_MCFTMR")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The biggest change is some refactoring of the H616 DRAM driver, which
allows better fine-tuning for each board, and is the base for pending
LPDDR3 and LPDDR4 support, needed by new boards. The sun8i-emac
Ethernet driver sees some refactoring that enables it for the Allwinner
D1 EMAC IP. The sunxi HDMI driver is now using more DT properties. Also
the early SPL code now supports some odd H616 SoC variant.
There are some more patches pending, that require the final review
touches and some testing, I will send a separate PR for them later.
The gitlab CI completed successfully, and I boot tested a few boards
with different SoCs, via FEL and SD card, into Linux.
- DDR Training sequence happens very fast. The speedup in boot time is
negligible by skipping the training sequence during 2nd boot or after.
So remove the check and skip.
- This change improves the robustness of DDR training. If u-boot crashed
during DDR training, the training could be left in a limbo state, where
the BootROM has recorded that it is already in a 2nd boot. The training
must be repeated in this scenario to get out of this limbo state, but due
to the check it cannot be performed.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a new config option CONFIG_MVEBU_SPL_SATA_BLKSZ for specifying block
size of SATA disk. This information is used during building of SATA
kwbimage and must be correctly set, otherwise BootROM does not load SPL.
For 4K Native disks CONFIG_MVEBU_SPL_SATA_BLKSZ must be set to 4096.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Currently kwboot expected that sector size for SATA image is always 512
bytes. If SATA image cannot be parsed with sector size of 512 bytes, try
larger sector sizes which are power of two and up to the 32 kB. Maximal
theoretical value is 32 kB because ATA IDENTIFY command returns sector size
as 16-bit number.
Signed-off-by: Pali Rohár <pali@kernel.org>
SATA kwbimage contains offsets in block size unit, not in bytes.
Until now kwbimage expected that SATA disk always have block size of 512
bytes. But there are 4K Native SATA disks with block size of 4096 bytes.
New SATA_BLKSZ command allows to specify different block size than 512
bytes and therefore allows to generate kwbimage for disks with different
block sizes.
This change add support for generating SATA images with different block
size. Also it add support for verifying and dumping such images.
Because block size itself is not stored in SATA kwbimage, image
verification is done by checking every possible block size (it is any
power of two value between 512 and 32 kB).
Signed-off-by: Pali Rohár <pali@kernel.org>
This allows image type print_header() callback to access struct
image_tool_params *params.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Find SATA block device by blk_get_devnum_by_uclass_id() function and read
from it the real block size of the SATA disk. In case of error, fallback
back to 512 bytes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Find SATA block device by blk_get_devnum_by_uclass_id() function and read
from it the real block size of the SATA disk.
Signed-off-by: Pali Rohár <pali@kernel.org>
In the early days of the Allwinner A64 U-Boot support, we relied on a
vendor provided "boot0" binary to perform the DRAM initialisation. This
replaced the SPL, and required to equip the U-Boot (proper) binary with
a vendor specific header to be recognised as a valid boot0 payload.
Fortunately these days are long gone (we gained SPL and DRAM support in
early 2017!), and we never needed to use that hack on any later 64-bit
Allwinner SoC.
Since this is highly obsolete by now, remove that option from the
defconfigs of all A64 boards. We leave the code still in here for now,
since some people expressed their interest in this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Some SoCs of the H616 family use a die variant, that puts some CPU power
and reset control registers at a different address. There are examples
of two instances of the same board, using different die revisions of the
otherwise same H313 SoC. We need to write to a register in that block
*very* early in the SPL boot, to switch the core to AArch64.
Since the devices are otherwise indistinguishable, let the SPL code read
that die variant and use the respective RVBAR address based on that.
That is a bit tricky, since we need to do that in hand-coded AArch32
machine language, shared by all 64-bit SoCs. To avoid build dependencies
in this mess, we always provide two addresses to choose from, and just
give identical values for all other SoCs. This allows the same code to
run on all 64-bit SoCs, and controls this switch behaviour purely from
Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
To switch the ARMv8 Allwinner SoCs into the 64-bit AArch64 ISA, we need
to program the 64-bit start code address into an MMIO mapped register
that shadows the architectural RVBAR register.
This address is SoC specific, with just two versions out there so far.
Now a third address emerged, on a *variant* of an existing SoC (H616).
Change the boot0.h start code to make this address a Kconfig
selectable option, to allow easier maintenance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
It turns out that some H616 and related SoCs (like H313) need TPR2
parameter for proper working. Add it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently twr2rd, trd2wr and twtp are constants, but according to
vendor driver they are calculated from other values. Do that here too,
in preparation for later introduction of new parameter.
While at it, introduce constant for t_wr_lat, which was incorrectly
calculated from tcl before.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Part of the code, previously known as "unknown feature", also doesn't
have constant values. They are derived from TPR0 parameter in vendor
DRAM code.
Let's move that code to separate function and introduce TPR0 parameter
here too, to ease adding new boards.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These values are highly board specific and thus make sense to add
parameter for them. To ease adding support for new boards, let's make
them same as in vendor DRAM settings.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Mentioned function result is always true and result isn't checked
anyway. Let's make it void.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor H616 DRAM code always configure part which we call ODT
configuration. Let's reflect that here too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor DRAM settings use TPR10 parameter to enable various features.
There are many mores features that just those that are currently
mentioned. Since new will be added later and most are not known, let's
reuse value from vendor DRAM driver as-is. This will also help adding
support for new boards.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While ODT values for same memory type are similar, they are not
necessary the same. Let's parameterize them and make parameter same as
in vendor DRAM settings. That way it will be easy to introduce new board
support.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fix code style for pointer declaration. This is just cosmetic change to
avoid checkpatch errors in later commits.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor DRAM code actually writes to whole CR register and not just sets
bit 31 in mctl_ctrl_init().
Just to be safe, do that here too.
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that all differences in functionality are covered by individual
flags, remove the enumeration of SoC variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While R40 puts the EMAC syscon register at a different address from
other variants, the relevant portion of the register's layout is the
same. Factor out the register offset so the same code can be shared
by all variants. This matches what the Linux driver does.
This change provides two benefits beyond the simplification:
- R40 boards now respect the RX delays from the devicetree
- This resolves a warning on architectures where readl/writel
expect the address to have a pointer type, not phys_addr_t.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
