Since 0dba45864b ("arm: Init the debug UART") ,
the debug_uart_init is now called from crt.S
It's no longer required to call it from the board file.
With the current code, the banned <debug_uart> is printed twice:
<debug_uart>
<debug_uart>
U-Boot 2022.07-rc4-00089-gee3d158fa8 (Jun 08 2022 - 17:39:29 +0300)
Remove all calls from board_early_init_f .
Suggested-by: Balamanikandan Gunasundar <Balamanikandan.Gunasundar@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Set blue led on at boot time in order to highlight that u-boot is loaded.
This is done for all sama5d2 based boards which contain an RGB led.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Wrap definition of board_usb_hw_init() around with #ifdef CONFIG_CMD_USB
to avoid warning: 'board_usb_hw_init' defined but not used
[-Wunused-function] when compiling without CONFIG_CMD_USB.
This patch makes sama5d27_som1_ek, sama5d2_ptc_ek and sama5d2_xplained
consistent with other boards that use the same #ifdef to avoid the warning.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Josef Lusticky <josef@lusticky.cz>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To fix the issue of write the rootfs.ubi, adjust the smc timings
configuration of the nand controller.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The drive strength has to be set to medium for the NAND data lines.
With a low drive, we can get some data corruption.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
