Add support to detect daughtercards (GESI Ethernet card) in-order
to set the MAC address of the main CPSW2G interface.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Update the default BOOTCOMMAND to provide an automatic and easier way
to configure ethernet PHY before loading the firmware.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Add board specific devicetree for Bananapi R3 SBC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Commit dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and
related functions") changed the logic deciding to set R0 and R1
registers for V1 devices.
Before:
/* Also set PUPD/R0/R1 if the pin has them */
err = mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_PUPD, !pullup);
if (err != -EINVAL) {
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R0, r0);
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R1, r1);
}
After:
/* try pupd_r1_r0 if pullen_pullsel return error */
err = mtk_pinconf_bias_set_pullen_pullsel(dev, pin, disable, pullup,
val);
if (err)
return mtk_pinconf_bias_set_pupd_r1_r0(dev, pin, disable,
pullup, val);
Tracing mtk_pinconf_bias_set_pullen_pullsel shows that the function
always either returns 0 in case of success or -EINVAL in case any error
has occurred. Hence the logic responsible of the decision to program R0
and R1 has been inverted.
This leads to problems on BananaPi R2 (MT7623N) when booting from
SDMMC, it turns out accessing eMMC no longer works since
U-Boot 2022.07:
MT7623> mmc dev 0
Card did not respond to voltage select! : -110
The problem wasn't detected for a long time as both eMMC and SDMMC work
fine if they are used to boot from, and hence R0 and R1 were already
setup by the bootrom and/or preloader.
Fix the logic to restore the originally intended and correct behavior
and also change the descriptive comment accordingly.
Fixes: dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and related functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to 8.
The C7x and VPAC have been overwhelming the DSS's access to the DDR
(when it was accessing via the Non Real-Time (NRT) Queue), primarily
because their functional frequencies, and hence DDR accesses, were
significantly higher than that of DSS. This led the display to flicker
when certain edgeAI models were being run.
With the DSS traffic serviced from the RT queue, the flickering issue
has been found to be mitigated.
The am62a qos files are auto generated from the k3 resource partitioning
tool.
Section-3.1.12, "QoS Programming Guide", in the AM62A TRM[1], provides
more information about the QoS, and section-14.1, "System Interconnect
Registers", provides the register descriptions.
[1] AM62A Tech Ref Manual: https://www.ti.com/lit/pdf/spruj16
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
J721E and J7200 have same file j721e_init.c which had the firewall
configs for J721E being applied on J7200 causing the warnings. Split the
firewalls for both the boards to remove those warnings.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The current documentation for Snapdragon based Samsung
and Qualcomm boards is vague in the sense that at one place
it mentions that u-boot can be used as a replacement for ABL
bootloader and at another it mentions that u-boot is loaded
as an Android boot image through ABL.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Currently a few 'board/qualcomm/../Makefile' point to incorrect
path of sdm845 board file.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
K3 devices have some firewalls set up by ROM that we usually remove so
that the development is easy in HS devices.
While removing the firewalls disabling a background region before
disabling the foreground regions keeps the firewall in a state where all
the transactions will be blacklisted until all the regions are disabled.
This causes a race for some other entity trying to access that memory
region before all the firewalls are disabled and causes an exception.
Since the background regions configured by ROM are in such a manner
that they allow all transactions, don't touch the background regions at
all.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Allow non fitImage bootflow on Field Securable (HS-FS) devices in
addition to GP, force fitImage boot only on Security enforced (HS-SE)
devices where signed images are necessary to maintain chain of trust.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
On modern Qualcomm platforms including SDM845 a GENI SE QUP IP
description is supposed to be found in board device tree nodes,
the version of the IP is used by the GENI UART driver to properly
set an oversampling divider value, which impacts UART baudrate.
The change touches dragonboard845c and starqltechn board device
tree source files, a device tree node label to "debug" UART is
renamed to 'uart9' according to the naming found in Linux.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Starting from QUP v2.5 the value of oversampling is changed from 32
to 16, keeping the old value on newer platforms results on wrong set
UART IP clock divider, thus the asked baudrate does not correspond to
the actually set with all the consequencies for a user.
The change links the driver to a new Qualcomm GENI SE QUP driver
to get its hardware version and update the oversampling value.
Deliberately the code under CONFIG_DEBUG_UART_MSM_GENI is not touched,
since a wanted baudrate can be controlled by setting a modified
CONFIG_DEBUG_UART_CLOCK build time variable.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
The name "se" is used in upstream Linux device trees and has been for
ages, long before this U-Boot-ism was introduced. Same goes for the
existing compatible. Get rid of that.
[vzapolskiy: removed a ready change in the driver]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
A compiler warns about a missing function prototype, which is valid
and fixed by converting the function into static one, also fix
interleaved local variable declarations and assignments.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Fixes: 324df15a29 ("serial: qcom: add support for GENI serial driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This a cosmetic change, which corrects code indentation in a few places.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
There is only one clock supplier to the serial IP, thus getting it by
name is not needed, also note that "clock-names" property is not listed
under doc/device-tree-bindings/serial/msm-geni-serial.txt, and finally
"se-clk" clock name is invalid, if added, it shall get "se" value like
it's already described in Linux device tree documentation.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
In preparation for supporting upstream Linux device trees on Qualcomm
platforms, make this the default behavior.
[vzapolskiy: extracted the driver change from a combination with dts changes]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
For whatever reason, likely a driver stub was copied from another
driver, the driver contains a bunch of unnecessary and confusing
includes like watchdog.h etc., the change reduces the list.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This change adds a Qualcomm GENI SE QUP device driver as a wrapper for
actually enabled and used serial devices found on a board.
At the moment the driver is pretty simple, its intention is to populate
childred devices and provide I/O mem read interface to them as clients,
this is needed for GENI UART driver to set up a proper clock divider
and provide the actually asked baud rate.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original Northstar is an ARM SoC series that comprise
BCM4709x and BCM5301x and uses a dual-core Cortex A9, the
global timer and a few other things.
This series should not be confused with North Star Plus
(NSP) which is partly supported by U-Boot already.
The SoC is well supported by the Linux kernel and OpenWrt
as it is used in many routers.
Since we currently don't need any chip-specific quirks
and can get the system up from just the device tree, a
mach-* directory doesn't even need to be added, just
some small Kconfig fragments.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This brings in the main SoC device tree used by the
Broadcom Northstar chipset, i.e. BCM4709x and BCM5301x.
This is taken from the v6.3 Linux kernel.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MAX14526 is a powerful extcon chip which allows detection of various
plugs like usb, mhl, uart, headset etc. This version of driver
implements support of AP-usb and CP-usb/uart paths.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new simple uclass for extcon. Currently all setup is done
in the probe. Uclass struct and ops are empty for now.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI autoconfig case for PCI_CLASS_PROCESSOR_POWERPC just prints debug
message and then calls autoconfig setup code like for any other standard
endpoint device. We do not need special debug message for it, so remove
this case and handle PCI_CLASS_PROCESSOR_POWERPC via default code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The files include/tpm* are an integral part of the TPM drivers.
The tpm* commands are used to access TPM devices.
Both should be managed by the TPM DRIVERS maintainer.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For the CONFIG_PHY case, move the PHY setup before the register access.
This avoids a hang when updating the imx8mm.dtsi which moves the
USB OTG power-domains to the PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Fabio Estevam <festevam@denx.de>
Currently, it is recommended to move from CFG_EXTRA_ENV_SETTINGS to
an env file, so do the conversion.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The bootcmd/altbootcmd mechanism is not invoked for bootmenus.
Manually compare bootcount and bootlimit to implement fallback on all
codepaths.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Defaults have changed, we do not want the bootmenu to contain EFI
options.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, only the first MAC address is read from the fuses.
The second MAC address is not read and Linux assigns a random one.
To prevent this behavior, read the second MAC address from the fuses
and store it into the eth1addr environment variable so that it
can be passed to Linux.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add lockdown U-Boot env support so that only certain U-Boot environment
variables are allowed to be modified.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Instead of loading the zImage kernel and the devicetree separately, switch
to the fitImage format, which is more convenient when working with secure
boot, for example.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
GPT Partition labels are used for determining the right
root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware
boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader.
One can overwrite the inactive hardware partition with new bootloader
and environment and afterwards switch the eMMC boot partition for an
atomic bootloader switch.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
When performing rootfs update via swupdate, it is convenient to check the
'ustate' variable to decide whether the update succeeded or not.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Run the altbootcmd script if any step of bootcmd fails.
This ensures that always a valid image can be run.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add an altbootcmd script, which is convenient way to integrate with
swupdate and perform a roll back of the previous working version in the
case of update failure.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add automatic boot counter that increases after every
reset. After a power-on reset, it will be initialized with 1,
and each reboot will increment the value by 1. By default it is
disabled if bootlimit isn't set.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Select CONFIG_CMD_SQUASHFS so that the SquashFS U-Boot commands
are available.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Introduce EXTRA_BOOTPARAMS to allow passing additional parameters
to kernel command line. This is useful for debugging purposes.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
It doesn't seem appropriate for arch/SOC to use a board-level
functionality (CONFIG_OF_BOARD_FIXUP), because this prevents boards
that need to do FDT fixup from using that feature.
Also, this code is completely dead and useless (from comments by
Rasmus Villemoes on the mailing list):
- No in-tree imx8m-based board seems to set CONFIG_OF_BOARD_FIXUP
- The nodes which that function wants to disable don't even exist in
the U-Boot copy of imx8mp.dtsi.
This code was introduced in commit 35bb60787b. It seems to be some
random import of code from downstream NXP U-Boot, with a commit
message that makes no sense in upstream context.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 787f04bb6a ("imx: add USB2_BOOT type") broke get_boot_device()
for IMX8 which affects booting from SDP due to boot_instance being
non-zero.
Fix this by only using boot_instance for imx8ulp and imx9.
Fixes: 787f04bb6a ("imx: add USB2_BOOT type")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add debug messages to print the real pixel clock rate, which may not be
the requested one.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add the get_lcd_clk() function to get the LCD pixel clock rate.
The patch has been tested on imx6ul platform.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
