This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."
An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.
Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
* Add netargs and netboot option.
* This enables tftp and nfs booting
* This puts omap5 devices inline with other devices such as am335x and am437x
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
* Since the emmc isn't always programed trying to load the fs from the
emmc causes boot failures/kernel panic.
* The current bootcmd is set to:
bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \
setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot;
My guess is the env variables should be set so that sd card boot
(dt,kernel,fs) is the default and then fallback to emmc if it fails (no
sd card detected)
The current bootcmd attempts to set mmcroot to the sd card rootfs but
that code doesn't run due to mmcboot being ran early on.
Signed-off-by: Franklin Cooper Jr. <fcooper@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree. In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Signed-off-by: Tom Rini <trini@ti.com>
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.
It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff. We don't do this by default to allow for
the most likely success of people using custom addresses however.
Signed-off-by: Tom Rini <trini@ti.com>
The ELM hardware engine wihich is used for ECC error detections is not present
on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to
SoC configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24 11:38:39 -05:00
Renamed from include/configs/omap5_common.h (Browse further)