The NETSEC GMAC occasionally falls into a weird state where
MAC_REG_DESC_SOFT_RST has never been cleared and shows errors like the
below when networking commands are issued:
=> ping 192.168.1.1
ethernet@522d0000 Waiting for PHY auto negotiation to complete... done
netsec_wait_while_busy: timeout
Using ethernet@522d0000 device
ARP Retry count exceeded; starting again
ping failed; host 192.168.1.1 is not alive
It happens on not only 'ping' but also 'dhcp', 'tftp' and so on.
Luckily, restarting the NETSEC GMAC and trying again seems to fix the
problematic state. So first ensure that we haven't entered the state by
checking MAC_REG_DESC_SOFT_RST to be cleared; otherwise, restarting
NETSEC/PHY and trying again would work as a workaround.
Signed-off-by: Ryosuke Saito <ryosuke.saito@linaro.org>
Tested-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
