Tabs not spaces, so transform it to the common styling.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The regulator enable-gpio uses opposite values for the declaration
vs. the enable_active_low property, breaking the regulator enablement.
Make the usbhost-supply work again by bringing them in sync again.
This mimics the upstream Linux change found on:
http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The gmac reset has opposite values for the gpio declaration
and the separate reset-active, bring this in line to make
u-boot also find the ethernet-phy.
This mimics the upstream Linux commit found on
https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Board has flash chip on board so let store U-Boot environment there.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Document SPI flash program steps for rockchip platforms.
Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On rockchip platforms, SPI boot image creation is not
straightforward like MMC boot image creation where former
requires to specify tpl, spl in multimage format in mkimage,
and later simply do a concatenate mkimaged-tpl with spl.
On this note, let drop rkspi image type creation via kbuild
and let inform via rockchip.rst
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
ROCKPro64 board.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Firefly RK3399 board.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The following problems are resolved:
* When booting via UEFI an SMBIOS table is presented to the operating
system. If U-Boot tries to add an empty string, this results in corrupted
SMBIOS information. We will now use "Unknown" as property value.
* The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver
the missing DM_RNG Kconfig dependency is added.
* Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are
added.
-----BEGIN PGP SIGNATURE-----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=tmqF
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc4 (2)
The following problems are resolved:
* When booting via UEFI an SMBIOS table is presented to the operating
system. If U-Boot tries to add an empty string, this results in corrupted
SMBIOS information. We will now use "Unknown" as property value.
* The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver
the missing DM_RNG Kconfig dependency is added.
* Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are
added.
Add the missing Kconfig dependency and let VIRTIO_RNG default to yes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
smbios_add_string() cannot deal with empty strings. This leads to incorrect
property values and invalid tables. E.g. for the pine64-lts_defconfig
CONFIG_SMBIOS_MANUFACTURER="". Linux command dmidecode shows:
Table 1:
Manufacturer: sunxi
Product Name: sunxi
Table 3:
Invalid entry length (2). DMI table is broken! Stop.
Replace empty strings by "Unknown".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific
checks in a localized area, so they aren't lost in the future.
- Complete / re-migrate some options from config headers to defconfigs
- Add dependencies to the various debug uart drivers
All of our cmds have a Kconfig entry. Making enabling a CMD via the
config file an error to checkpatch.pl.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is a lot of use of #ifdefs in U-Boot. In an effort reduce this,
suggest using the compile-time construct.
Signed-off-by: Simon Glass <sjg@chromium.org>
A common problem when submitting a new uclass is to forget to add sandbox
tests. Add a warning for this.
Of course tests should always be added for new code, but this one seems to
be missed by nearly every new contributor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option to indicate that U-Boot-specific checks should be enabled.
Add a function to house the code that will be added.
Signed-off-by: Simon Glass <sjg@chromium.org>
Keep the U-Boot changes to $logFunctions
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Resync with v5.7 release which changed the default max line
length, update commit to reflect]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BZIP2
CONFIG_GZIP
CONFIG_LZO
CONFIG_ZLIB
CONFIG_LZMA
CONFIG_LZO
Signed-off-by: Tom Rini <trini@konsulko.com>
Per the boards config header file, there is no useful GPIO on these
boards. Remove CONFIG_CMD_GPIO from the defconfigs.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled. Disable them from the defconfig and
enable them in the header.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the
commands being disabled. Enable them via the defconfig.
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file. In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig. Disable it in the defconfig, cleanup
the header.
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Debug console is the part of serial driver in the same file. It means to be
able to enable debug console you also need to enable driver itself.
That's why add all dependecies and list only debug consoles which are
enabled based on driver selection to avoid compilation error when user
asks for certain debug console but driver is not enable for it.
Error:
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `putc':
/home/monstr/data/disk/u-boot/common/console.c:513: undefined reference to `printch'
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `puts':
/home/monstr/data/disk/u-boot/common/console.c:563: undefined reference to `printch'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix ns16550 dependency, add ZYNQ_SERIAL, change S5P]
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl7YxFMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyJnICACR6Q6OclfIuM0A3ubV
GV48+iVz55eZnrZFKkbALBNjwTsshLpdZ/7Lr4zPD5e/FmrbJ+RONd0B6E38fSJk
Rq1ZwMyuR6yv+LAb9+La36tGqD9bCFewqBpR5LQNOdjE+fG66rrWxksMME1jOIr5
FLpFkk3lmEUloQumHDCQUgzXC/TUWpedgxpT15l1nR/Ovkh/MPvggIdS2zMWw92J
oA9shaNTVLd//W9icduXagNtRMsjscmf/zTZFCYgBRjUZgiPW+HnitWg7jqbYIuY
AqmNBZIrC6OuZ7W447g1rMGwbwQ5T9vbydp6PpHVqPvTt3D8OZ9h1+Hwwie7u9O1
CPaV
=xLcT
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.07-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.07 cycle
This set includes just two small commits that fix a build warning and
add a missing serial node.
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55e ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Change the compatible string to "fsl,etsec2" for the Ethernet ports,
which is used in the current driver's match table.
Fixes: 69a00875e3 ("doc: dt-bindings: Describe Freescale TSEC ethernet controller")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable DM_ETH on all the defconfigs for the T1024RDB board.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable DM_ETH on all the defconfigs for the P2041RDB board.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the T1024RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
T102x SoCs. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P5040DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
