Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds DWMMC device node data for exynos5.
This patch also adds binding file for DWMMC device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
simple-framebuffer is a new device tree binding that describes a pre-
configured frame-buffer memory region and its format. The Linux kernel
contains a driver that supports this binding. Implement functions to
create a DT node (or fill in an existing node) with parameters that
describe the framebuffer format that U-Boot is using.
This will be immediately used by the Raspberry Pi board in U-Boot, and
likely will be used by the Samsung ARM ChromeBook support soon too. It
could well be used by many other boards (e.g. Tegra boards with built-in
LCD panels, which aren't yet supported by the Linux kernel).
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Debug trace buffers are memory mapped in DCSR space beyond 4M.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Allow VDD voltage overriding with a command. This is an add-on feasture of
VID. To override VDD, use command vdd_override with the value of voltage
in mV, for example
vdd_override <voltage in mV, eg. 1050>
The above example will set the VDD to 1.050 volt. Any wrong value out of
range of 0.8188 to 1.2125 volt or invalid string is ignored.
In addition to the command, if overriding VDD is needed earlier in booting
process, save an variable and reboot:
setenv t4240qds_vdd_mv <voltage in mV>
saveenv
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add NAND partition table, EK board support boot up NAND flash using
the same NAND partition table
Add Index in this file
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch add following EK information
- at91sam9n12ek, at91sam9x5ek
- sama5d3xek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch implement following things
- The link no longer accessable
- Remove the error configuration command
- Update soldered data flash memory map
- Update at91sam9m10g45ek memory size to 128MiB
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM.
This document explains thse usecases and the detailed explanation of what needs
to be done to use it.
Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes
of CCSRBAR etc.
The changes are not very large, but it is good to document them so that user
can get it working at once.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Easier for using with patman.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement BOOT_OFFSET command for imximage. This command is parallel
to current BOOT_FROM command, but allows more flexibility in configuring
arbitrary image header offset. Also add an imximage.cfg with default
offset values into arm/arch/imx-common/ so the board-specific imximage.cfg
can include this file to avoid magic constants.
The syntax of BOOT_OFFSET command is "BOOT_OFFSET <u32 offset>".
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
With 'mtest' no longer a default command, we will have unused defines
which should be removed for the v2013.10 release.
Signed-off-by: Tom Rini <trini@ti.com>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This reverts commit 1285a2808a since the migration
of boards from Makefile to boards.cfg is now complete.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
We shall remove these OMAP4/5-specific options in v2013.07, barring
insufficient progress on the kernel side.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
The kernel states:
---8<---
The OMAP3 GPMC hardware BCH engine computes remainder polynomials, it does not
provide automatic error location and correction: this step is implemented using
the BCH library.
--->8---
And we do so in u-boot.
This implementation uses the same layout for BCH8 but it is fix. The current
provided layout does only work with 64 Byte OOB.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mansoor Ahamed <mansoor.ahamed@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
Introduce 'mx28evk_nand' target for saving environment variables into NAND.
The mx28evk board does not come with a NAND flash populated from the
factory. It comes with an empty slot (U23), which allows the insertion of a
48-pin TSOP flash device.
Tested with a K9LBG08U0D.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This patch provides a support to build the user specified dts.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
The "bootmenu" command uses U-Boot menu interfaces and provides
a simple mechanism for creating menus with several boot items.
When running this command the menu will be assembled as defined
by a set of environment variables which contain a title and
command key-value pairs. The "Up" and "Down" keys are used for
navigation through the items. Current active menu item is
highlighted and can be selected using the "Enter" key.
The command interprets and generates various ANSI escape
sequencies, so for proper menu rendering and item selection
the used terminal should support them.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[agust: various fixes and documentation updates]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Checking the default menu item and obtaining its data can
be useful in custom menu code. Export menu_default_choice()
function which serves this purpose.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Selecting menu items is currently done in menu_interactive_choice()
by reading the user input strings from standard input.
Extend menu_interactive_choice() to support user defined function
for selecting menu items. This function and its argument can be
specified when creating the menu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This adds a member to TMU FDT node for providing hardware
tripping temperature threshold.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fdt entry for Exynos TMU driver specific pre-defined values used for
calibration of current temperature and defining threshold values.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
The "mtest" command is of little practical use (if any), and
experience has shown that a large number of board configurations
define useless or even dangerous start and end addresses. If not even
the board maintainers are able to figure out which memory range can be
reliably tested, how can we expect such from the end users? As this
problem comes up repeatedly, we rather do not enable this command by
default, so only people who know what they are doing will be
confronted with it.
As this changes the user interface, we allow for a grace period
before this change takes effect. For now, we make "mtest"
configurable through the CONFIG_CMD_MEMTEST variable, which is defined
in include/config_cmd_default.h; we also add an entry to
doc/feature-removal-schedule.txt which announces the removal of this
default setting in two releases from now, i. e. with v2013.07.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
On some architectures certain values of splashimage will lead to
a data abort exception.
Document the problem, and implement a callback for splashimage to
reject such values.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Simple howto to add support to a board
for booting the kernel from SPL ("Falcon" mode).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Commit 8b710b1 started removing code for the unmaintained "ns9750dev"
board; the board support is still broken, and not included anywhere in
the Makefile or boards.cfg. Remove the remaining dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Added README file with the description of required options and host
configuration to use network SPL with am335x targets. Briefly discuss
how to use this configuration to program empty boards.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
Documentation fix to README.fsl-ddr to fix typos and
to reflect use of 'd' hotkey to enter the FSL DDR debugger.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add copy command which allows copying of DIMM/controller settings.
This saves tedious retyping of parameters for each identical DIMM
or controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using environmental variable "ddr_interactive" to activate interactive DDR
debugging seomtiems is not enough. For example, after updating SPD with a
valid but wrong image, u-boot won't come up due to wrong DDR configuration.
By enabling key press method, we can enter debug mode to have a chance to
boot without using other tools to recover the board.
CONFIG_FSL_DDR_INTERACTIVE needs to be defined in header file. To enter the
debug mode by key press, press key 'd' shortly after reset, like one would
do to abort auto booting. It is fixed to lower case 'd' at this moment.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.
B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
configuration reset source. The RCW source is set by appropriate
DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
- total four refclk, including CPRI clock scheme
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add SPI device node data for exynos.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add sound device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The silent variable now updates the global data flag anytime it is
changed as well as after the env relocation (in case its value is
different from the default env in such cases as NAND env)
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL
and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once
the last mpc85xx nand_spl target is gone.
CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't
seem right to overload it for meaning SPL as well as nand_spl does. Even
if it's somewhat appropriate for the main u-boot, the SPL itself isn't
(necessarily) ramboot, and we don't have separate configs for SPL and
main u-boot. It was also inconsistent, as other platforms such as
mpc83xx didn't use CONFIG_RAMBOOT in this way.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Add LCD definitions and also a proposed binding for LCD displays.
The PWM is as per what will likely be committed to linux-next soon.
The displaymode binding comes from a proposal here:
http://lists.freedesktop.org/archives/dri-devel/2012-July/024875.html
The panel binding is new, and fills a need to specify the panel
timings and other tegra-specific information. Should a binding appear
that allows the pwm to handle this automatically, we can revisit
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This binding will apparently soon be in linux-next. Bring it in now
since we need to do something, and may as well try to target what
Linux will have.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The mx5 lowlevel_init.S contains board-specific code based on the reference
design. Let's keep it since it avoids creating new lowlevel_init files and it
may be used by many boards. But add a config to make it optional in order not to
cause issues on boards not following this part of the reference design.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Grame is still listed since he has agreed to continue with some review.
Also add an alias to shorten things.
Signed-off-by: Simon Glass <sjg@chromium.org>
This makes the FAT and ext4 filesystem implementations build if
CONFIG_FS_{FAT,EXT4} are defined, rather than basing the build on
whether CONFIG_CMD_{FAT,EXT*} are defined. This will allow the
filesystems to be built separately from the filesystem-specific commands
that use them. This paves the way for the creation of filesystem-generic
commands that used the filesystems, without requiring the filesystem-
specific commands.
Minor documentation changes are made for this change.
The new config options are automatically selected by the old config
options to retain backwards-compatibility.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move spin table to cached memory to comply with ePAPR v1.1.
Load R3 with 64-bit value if CONFIG_SYS_PPC64 is defined.
'M' bit is set for DDR TLB to maintain cache coherence.
See details in doc/README.mpc85xx-spin-table.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Based on populated DIMMs, automatically select from cs0_cs1_cs2_cs3 or
cs0_cs1 interleaving, or non-interleaving if not available.
Fix the message of interleaving disabled if controller interleaving
is enabled but DIMMs don't support it.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add code for configuring VSC3316/3308 crosspoint switches
Add README to understand the APIs
- VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch
capable of data rates upto 11.5Gbps. VSC3316 has 16 input and 16
output ports whereas VSC3308 has 8 input and 8 output ports.
Programming of these devices are performed by two-wire or four-wire
serial interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Implement kerneldoc template for linker-generated arrays. This is
the first template in U-Boot that is used to generate kerneldoc
style documentation. This template is very basic.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch converts the old method of creating a list of command
onto the new LG-arrays code. The old u_boot_cmd section is converted
to new u_boot_list_cmd subsection and LG-array macros used as needed.
Minor adjustments had to be made to the common code to work with the
LG-array macros, mostly the fixup_cmdtable() calls are now passed the
ll_entry_start and ll_entry_count instead of linker-generated symbols.
The command.c had to be adjusted as well so it would use the newly
introduced LG-array API instead of directly using linker-generated
symbols.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add STDIO documentation template.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
[trini: Fix DOCBOOKS line as we don't have linker_lists yet]
Signed-off-by: Tom Rini <trini@ti.com>
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Import basic CSS stylesheet for the HTML documentation. The base for
the stylesheet is taken from:
http://ds9a.nl/docbook/minimal-page.html
I customized the CSS a bit further, for example to add curvy corners
to example section and change the tint of gray. The HTML documentation
does not look that crude anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Pull slightly modified version of Documentation/DocBook, the related perl
script scripts/kernel-doc and the scripts/docproc.c from Linux kernel and
implant it into U-Boot. This will allow smooth generation of kerneldoc
style documentation.
It was necessary to modify the DocBook/Makefile to work with U-Boot build
system. The changes were only minor though and involved replacing the kbuild
specific parts.
It was also necessary to replace use of variables like KERNEL_VERSION with
U_BOOT_VERSION, strings like Linux kernel with U-Boot Bootloader etc. so
the generated result actually matches.
Finally, it was necessary to adjust docproc.c, since the documentation in
U-Boot is located in doc/DocBook instead of Documentation/DocBook as is in
case of the Linux kernel.
Some parts of the DocBook Makefile are unused, but to allow easier sync with
Linux kernel, these parts are still left in. The targets enabled now are
"htmldocs" "pdfdocs" "psdocs" "xmldocs" and "cleandocs" to remove the results
of documentation build.
Linux scripts/docproc.c:
commit f0f3ca8d967462dafb815412b14ca3339b9817a6
Date: Wed Jun 15 11:53:13 2011 +0200
Linux scripts/kernel-doc:
commit 1b40c1944db445c1de1c47ffd8cd426167f488e8
Date: Sun Aug 12 10:46:15 2012 +0200
Linux Documentation/DocBook:
commit bb8187d35f820671d6dd76700d77a6b55f95e2c5
Date: Thu May 17 19:06:13 2012 -0400
Signed-off-by: Marek Vasut <marex@denx.de>
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Support of the MINI2440 board from FriendlyARM from
an old version of u-boot :
http://repo.or.cz/r/u-boot-openmoko/mini2440.git
Currently, supporting only boot from NOR.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Now DT support is becoming common for all new SoC's. Hence it is better
to have option for getting specific FDT from the remote server.
This patch adds support for new label i.e. 'fdt'. This will allow to
retrieve 'fdt blob' from the remote server. This patch take care for
the following scenarios.
The usage of fdt is optional.
The 'fdt blob' can be retrieved from tftp or can be available locally
or can be absent.
If 'fdt_addr_r' environment variable is set and 'fdt' label is defined
retrieve 'fdt blob' from tftp. 'fdt_addr_r' is then passed along bootm
command.
If 'fdt_addr' is set and 'fdt blob' is not retrieved from the tftp pass
'fdt_addr' to bootm command. In this case 'fdt blob' will be available
at 'fdt_addr'.
If 'fdt_addr' is not set and 'fdt blob' is not retrieve from tftp pass
NULL to boot command. In this case 'fdt blob' is not required and absent.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
Allow a board to configure a larger buffer for netconsole, but leave
the default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
It is desirable to use different port numbers for sending and receiving
packets with netconsole in the case where you have more than one device
on the local subnet with netconsole enabled for broadcast. When they
use the same port for both, any output from one will look like input to
the other. This is typlically not desirable.
This patch allows the input and output ports to be specified separately
in the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This board is the only board that still sticks to OneNAND IPL.
Remove this board, since we have SPL around for a while and
OneNAND is well supported in the SPL framework. The board can
be revived if necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tom Rini <trini@ti.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add a NAND controller along with a bindings file for review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Hi,
This adds to the documenation to explain how to use the
kwbimage.cfg file necessary to generate an image with
prefixed board setup values necessary for the kirkwood
boards.
Signed-off-by: Karl O. Pinc <kop@meme.com>
