With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
The MMC card detect pin is connected to gpio127 on omap3_logic.
When setting up the pbias register for MMC, let's also enable
gpio_127 for the card detect. As part of the package deal,
gpio_126 and gpio_129 are also enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
When used with a device tree, this will extract the card detect
and write protect pins from the device tree and configure them
accordingly. This assumes the GPIO_ACTIVE_LOW/HIGH is supported
by da8xx_gpio.
Signed-off-by: Adam Ford <aford173@gmail.com>
With CONFIG_BLK becoming a requirement, the Davinci MMC driver
needs to be updated with DM_MMC support. Since SPL is tiny and
many boards do not support DM in SPL, this retains the backwards
compatibility for those boards who need to initialize MMC manually
in SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
The getcd and getwp functions when DM_MMC is enabled are
assumming the DM_GPIO is enabled. In cases (like SPL) where
DM_GPIO may not be enabled, wrap these calls in an #ifdef
Signed-off-by: Adam Ford <aford173@gmail.com>
AM654 has an arasan sdhci controller and a mmc phy attached to it.
Add basic support for K3 specific arasan sdhci controller.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The dev_get_priv(dev) is used twice in the probe function.
Replace the second invocation with priv variable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for fetching the clock frequency both using the legacy
method in case clock framework is disabled as well as via the clock
framework if it is enabled. This allows for migration to the clock
framework on platforms which supports it while not breaking legacy
platforms. That said, the legacy method must be removed eventually.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
This commit enables support for Exynos Designware MMC driver based on DM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
By convention for DM_MMC the host->priv is used to store struct udevice
*dev pointer.
Unfortunately, the legacy Exynos DW MMC code uses this field to
store pointer to dwmci_exynos_priv_data struct
Hence, we do need to get data in other way - namely by using container_of
when host pointer is present.
In this way the sdr_timing data is properly accessed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit prevents memory leak when this function is used with DM_MMC
as the struct dwmci_exynos_priv_data is already allocated by DM.
It is necessary for NON DM aware devices to allocate this struct first.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As platform uses GPIOs for card detection, it's
simpler and more readable to use GPIO_ACTIVE_(LOW|HIGH)
in the gpio flags instead of using the cd-inverted
property.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add missing clk_free() call in case of failure
when enabling the clock.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Config flag CONFIG_BLK becomes mandatory, update arm_pl180_mmci
to support this config.
This driver is used by STM32Fx and by Vexpress platforms.
Only STM32Fx are DM ready. No DM code is isolated and will be
removed easily when wexpress will be converted to DM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.
3 states managed in driver:
1/ reset: SDMMC disable, signal HiZ
2/ power-cycle: SDMMC disable, signals drive to 0
3/ power-on: SDMMC enabled
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit dd27918c22 ("dm: mmc: sunxi: Add support for driver model")
only added the allwinner,sun5i-a13-mmc compatible string for this
driver. The DM initialisation code here also works with (at least) A10
and A20, so add the appropriate compatible strings as per Linux 4.17's
driver.
Tested on A10 Cubieboard and A20 pcDuino3 Nano with CONFIG_DM_MMC.
(A20 worked already, because sun7i-a20.dtsi specifies both the A13 and
A20 strings.)
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Add code to reset all reset signals as in mmc DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Code around tuning_loop_counter variable expects to go below zero.
That's why this variable can't use unsigned type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixes the mmc tuning command failures
when tuning pattern data needs to read back for
comparision against the expected bit pattern.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add new compatible to the Uniphier SD driver for R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds HS200 suuport for ZynqMP and enables
the same for ZC1751 DC1 board which has eMMC on it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The compatible string of ftsdc010_mci.c is different from
the mmc driver in Linux Kernel. Modify it for consistency.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
SDMMC_CMD_CPSMEN bit is wrongly check and set in
SDMMC_ARG register instead of SDMMC_CMD register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=te7/
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-05-24
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.
The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.
Reported-by: Jan Leonhardt <jan@cyberdesigner.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
The check is necessary to avoid NULL pointer dereference.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Drop all the extra content from the MMC core, so that tiny MMC support
is really tiny, no fancy anything. That means the tiny MMC support does
only 1-bit transfers at default speed settings. Moreover, this patch
drops duplicate instance of struct mmc mmc_static, which wasted about
360 bytes. Furthermore, since MMC tiny supports only one controller
at all times, get rid of mallocating the ext csd backup and replace
it with static array. All in all, this patch saves ~4 kiB of bloat
from the MMC core, which on platforms with severe limitations can be
beneficial.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup checkpatch.pl style warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support of SD3.0 for ZynqMP.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads the capabilities register1 and update the host
caps accordingly for mmc layer usage. This patch mainly reads
for UHS capabilities inorder to support SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to invoke any platform specific tuning
and delay routines if available.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to disable clock if clk_disable
was set and then enable or set clock if the clock was changed
or clock was disabled when clock needs to be enabled.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return type of
get_timer() function is ulong.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
