Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD
mode, make use of mode_rx field of dm_spi_slave_platdata to determine
whether to enable or disable QUAD mode. This is necessary to support
muliple SPI controllers where one of them may not support QUAD mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
AHB address can be as long as 32 bit, hence remove the
CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
and read as u32 value, it anyway does not make sense to mask upper bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The indirect read code is a pile of nastiness. This patch replaces
the whole unmaintainable indirect read implementation with the one
from upcoming Linux CQSPI driver, which went through multiple rounds
of thorough review and testing. All the patch does is it plucks out
duplicate ad-hoc code distributed across the driver and replaces it
with more compact code doing exactly the same thing. There is no
speed change of the read operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
The indirect write code is buggy pile of nastiness which fails horribly
when the system runs fast enough to saturate the controller. The failure
results in some pages (256B) not being written to the flash. This can be
observed on systems which run with Dcache enabled and L2 cache enabled,
like the Altera SoCFPGA.
This patch replaces the whole unmaintainable indirect write implementation
with the one from upcoming Linux CQSPI driver, which went through multiple
rounds of thorough review and testing. While this makes the patch look
terrifying and violates all best-practices of software development, all
the patch does is it plucks out duplicate ad-hoc code distributed across
the driver and replaces it with more compact code doing exactly the same
thing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Replace numerical bit shift with BIT macro
in cadence_qspi_apb
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch makes the code compatible with FIFO depths other than 4
bytes. It also simplify read/write FIFO loops.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
There is no need to re-configure sram partition for every read/write for
better full use of sram for read or write. This patch divides the half
sram for read & half for write once at initialization.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This driver is cloned from the Altera Rockerboard.org U-Boot
repository. I used this git tag: ACDS14.0.1_REL_GSRD_RC2. With Some
modification to support the U-Boot driver model (DM).
As mentioned above, in this new version I ported this driver to the
new driver model (DM). One big advantage of this move is that now
multiple SPI drivers can be enabled on one platform. And since the
SoCFPGA also has the Designware SPI master controller integrated,
this feature is really needed to support both controllers.
Because of this, this series needs the DT support for SoCFPGA
to be applied. For DT based probing in the SPI DM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
