Commit graph

17 commits

Author SHA1 Message Date
Simon Glass
e1d23dc912 Correct SPL use of RENESAS_SDHI
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_RENESAS_SDHI defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10 07:41:40 -05:00
Hai Pham
4dbbc3f373 clk: renesas: Switch to new SD clock handling
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.

Based on Linux series by Wolfram Sang, commit bb6d3fa98a41 ("clk:
renesas: rcar-gen3: Switch to new SD clock handling") and commit
e5f7e81ee430a ("mmc: renesas_sdhi: Parse DT for SDnH")

Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek: - Add rcar_clk_* prefix to all functions
       - Fix missing ~ in GENMASK(a, b), use clrsetbits_le32 instead
       - Use DIV_ROUND_CLOSEST, else if parent clock = 199999992 and
         rate = 200000000, the divider would be 0 and table lookup
	 would fail.
       - Turn rcar_clk_get_table_val into signed integer, so it can
         return 0 as a valid value and negative values as errors.
       - Make the code operate on correct clock and add comment
         which explains the reasoning behind it.
       - Rebase on changes to
         clk: renesas: Introduce and use rcar_clk_get_rate64_div_table function
2023-02-02 01:49:20 +01:00
Hai Pham
3c78ce8680 mmc: renesas-sdhi: Flag non-standard SDnH handling for V3M
V3M handles SDnH differently than other Gen3 SoCs, so let's add a
separate entry for that. This will allow better SDnH handling in the
future.

Based on Linux commit 627151b4966f ("mmc: renesas_sdhi: Flag
non-standard SDnH handling for V3M") by Wolfram Sang

Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2023-02-02 01:49:20 +01:00
Marek Vasut
8a73bef338 mmc: tmio: sdhi: Configure internal DMA bus width
The R-Car3 SDHI should set these two bits in DMA_MODE register according
to the specification, to indicate 64bit bus width. No other bus width
options are permitted and the default value is 0, which is incorrect.
Set the bits accordingly.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-01-31 14:08:45 +01:00
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Marek Vasut
4a66d4ee33 mmc: tmio: sdhi: Implement get_b_max function
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.

Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
  => time mmc read 0x0000000700000000 0 0x10000
  time: 0.151 seconds
  => time mmc read 0x0000000700000000 0 0x100000
  time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
  => time mmc read 0x0000000700000000 0 0x10000
  time: 0.156 seconds
  => time mmc read 0x0000000700000000 0 0x100000
  time: 2.349 seconds

Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2020-04-22 20:41:56 +08:00
Marek Vasut
56b0bb96be mmc: tmio: sdhi: Add calibration tables
Instead of using single fixed value for the calibration offset,
add tables which dynamically adjust this per calibration code
from the SCC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-11-27 16:56:46 +08:00
Marek Vasut
1bdcb83d29 mmc: tmio: sdhi: Skip bad taps
Some of the tuning taps produce suboptimal results. Add code
which skips those "bad" taps.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-11-27 16:56:46 +08:00
Marek Vasut
37c3990664 mmc: tmio: sdhi: Track SMPCMP valu in private data
Retain the SMPCMP value from last calibration in private data.
This will be later used for skipping bad taps.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-11-27 16:56:46 +08:00
Marek Vasut
0196a58a79 mmc: tmio: sdhi: Track current tap number in private data
Retain the tap number from last calibration in private data. This
will be later used for SCC error checking after each command.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-11-27 16:56:46 +08:00
Marek Vasut
b5900a58ca mmc: tmio: sdhi: HS400 manual adjustment
Since Gen3 SDHI has an internal DS signal AC-spec violation in HS400 mode,
CRC-error may occur in read command in HS400 mode. This phoenomenon occurs
at low/high temperature.

To fix this, after completion of HS400 tuning, enable manual calibration.
However, Gen3 M3 Ver.1.2 or earlier and H3 1.x does not support HS400.
These SoC forcibly use HS200 mode by SoC attribute.

The DT adjustment of the tuning parameters is not supported until the
DT property names become clear.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adapted from a patch by Takeshi Saito <takeshi.saito.xv@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
2019-05-21 22:15:32 +02:00
Marek Vasut
992bcf4f27 mmc: tmio: Make DMA transfer end bit configurable
Different versions of the SDHI core use either bit 17 or bit 20 for the
DTRAEND indication, which can differ even between SoC revisions. Make
the DTRAEND bit position part of the driver private data, so that the
probe function can set this accordingly. Set this to 20 on Socionext
SoCs and either 17 or 20 on Renesas SoCs, depending on the SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-09 11:08:40 +01:00
Marek Vasut
50aa1d99ed mmc: tmio: sdhi: Add HS400 support
Add support for the HS400 mode to SDHI driver. This uses the up-tune
mechanism from already supported HS200 tuning.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03 12:51:17 +01:00
Marek Vasut
95ead3d98d mmc: tmio: sdhi: Move tap_pos to private data
Move the tap_pos variable, which is the HS200/HS400/SDR104 calibration
offset, into private data, so it can be passed around. This is done in
preparation for the HS400 mode, which needs to adjust this value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03 12:51:17 +01:00
Marek Vasut
8ec6a04b6b mmc: tmio: Switch to clock framework
Switch the driver to using clk_get_rate()/clk_set_rate() instead of
caching the mclk frequency in it's private data. This is required on
the SDHI variant of the controller, where the upstream mclk need to
be adjusted when using UHS modes.

Platforms which do not support clock framework or do not support it
in eg. SPL default to 100 MHz clock.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
---
V2: - Fix build on certain platforms using SPL without clock framework
V3: - Turn clk_get_rate into a callback and fill it as needed on both
      renesas and socionext platforms
2018-12-03 12:51:16 +01:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Marek Vasut
cb0b6b035a mmc: tmio: Rename Matsushita to TMIO
Synchronize the naming with Linux, call the common code TMIO.
No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-14 00:03:30 +02:00