This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Most of the boards we support with H3/H5 enable DRAM on-die termination,
which is consistent with the high DRAM clocks that are used.
Make it the default (like it's done for other similar platforms) instead
of defining it in each defconfig.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Most H3/H5 boards we support have the DRAM ZQ value set to 3881979,
which is also consistent with the default set for the R40.
Make this value the default on H3/H5 instead of 123.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
