This commit enables imx28 based XEA board's u-boot.sb (SPL) to download
u-boot proper (u-boot.img) via Ymodem protocol.
This is extremely useful in the recovery scenario where u-boot.sb is
downloaded via uuu utility to SDRAM [*], and then one can upload u-boot
proper via serial console to fully debrick the device.
Note - debricking procedure of imx28 devices:
- NXP's original USB based tools (like mxsldr or uuu) expect single
u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and
U-Boot proper distinction.
[*] On Host:
------------
cat << EOF > imx28_xea.lst
uuu_version 1.3.0
SDPS: boot -f /srv/tftp/xea/u-boot.sb
SDPU: done
EOF
Please start picocom:
sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1
sudo ./uuu/uuu -V imx28_xea.lst
On the U-boot console one shall see:
Trying to boot from UART
CCC
Then please press CTRL+A, S
and type u-boot.img
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_FORCE_MMC_BOOT was removed in a previous patch as its
behavior is the correct one in all cases. Remove all uses of it from
defconfigs.
This reverts commit 3201e5b444 and removes
CONFIG_SPL_FORCE_MMC_BOOT from the imx28_xea defconfig.
Signed-off-by: Harald Seiler <hws@denx.de>
Redundant envs help with assuring better reliability for the system as they
prevent from the situation when envs are stored only in a single place.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
