Commit graph

10 commits

Author SHA1 Message Date
Stephen Warren
bbca7108db ARM: tegra: import latest Jetson TK1 spreadsheet
This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads.

The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-04 13:31:04 -07:00
Stephen Warren
7fb82986be ARM: tegra: rm Jetson TK1 PMIC GPIO programming
The PMIC is configured such that its GPIOs have the correct configuration
at power-up, so no programming is required.

In fact, the current programming is actively wrong, since:

(a) the AS3722 driver configures the GPIO to be an output before setting
its output value, which causes a 0v glitch on the output.

(b) the AS3722 driver configures the GPIO to drive a high voltage from its
VSUP_GPIO power source rather than its VDD_GPIO_LV power source, so the pin
drives 5V not 1.8V as desired.

Solve these problems by removing the code which configures the PMIC GPIOs.

Note that this patch was tested directly on top of v2016.01; since then,
commit 96350f729c "dm: tegra: net: Convert tegra boards to driver model
for Ethernet" prevents PCIe from being initialized. Alternatively, simply
revert that commit to get PCIe Ethernet working again, then apply this
patch to test.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-01-28 10:32:31 -07:00
Simon Glass
96350f729c dm: tegra: net: Convert tegra boards to driver model for Ethernet
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12 10:19:09 -07:00
Alexandre Courbot
d6bf06c0c7 ARM: tegra: simplify GPU setup
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.

Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Alexandre Courbot
a38a3c4af4 ARM: tegra: enable GPU DT node when appropriate
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.

Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-06 10:50:03 -07:00
Stephen Warren
c1fe92fe29 ARM: tegra: import latest Jetson TK1 pinmux
Syseng has revamped the Jetson TK1 pinmux spreadsheet, basing the content
completely on correct configuration for the board/schematic, rather than
the previous version which was based on the bare minimum changes relative
to another reference board.

The new spreadsheet sets TRISTATE for any input-only pins. This only works
correctly if the global CLAMP bit is not set, so the Jetson TK1 board code
has been adjusted accordingly. Apparently syseng have changed their mind
since the previous advice that this needed to be set:-/

This content comes from Jetson_TK1_customer_pinmux.xlsm (v09) downloaded
from https://developer.nvidia.com/hardware-design-and-development.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-04 10:08:58 -07:00
Thierry Reding
6e2fca94ff ARM: tegra: Enable PCIe on Jetson TK1
The Jetson TK1 has an ethernet NIC connected to the PCIe bus and routes
the second root port to a miniPCIe slot. Enable the PCIe controller and
the network driver to allow the device to boot over the network.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-12-18 13:19:21 -07:00
Stephen Warren
4ff213b8e4 ARM: tegra: clamp inputs on Jetson TK1
The HW-defined procedure for booting Tegra requires that
CLAMP_INPUTS_WHEN_TRISTATED be enabled before programming the pinmux.
Modify the Jetson TK1 board to do this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stephen Warren
9348532f51 ARM: tegra: make use of GPIO init table on Jetson TK1
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. This patch implements this
procedure for Jetson TK1. For pins which are to be used as GPIOs, the
pinmux mux function need not be programmed, so the pinmux table is also
adjusted.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stephen Warren
e04bfdacb3 ARM: tegra: add Jetson TK1 board
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00