The chapter in which the table explaining the image format changed
chapter as the document evolved. This should help people track the
info down faster.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.
This is generated command line when PMUFW_INIT_FILE is setup.
./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
MRC (Memory Reference Code) is a binary blob used to set up the SDRAM
controller on some Intel boards. Add a test for this feature.
With this test coverage on binman is back up to 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test for this feature. It allows SPL to hold a pointer to the
microcode block. This is used for 64-bit U-Boot on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a main program so that the tests can be executed directly, without
going through the main binman program.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test that the 'entry' module works with or without importlib.
The tests are numbered so that they are executed in the correct order.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a little check at the top of entry.py which decides if importlib
is available. At present this has no test coverage. To add this we will
need to import the module twice, once with importlib and once without.
In preparation for allowing a test to control the importing of this
module, remove all global imports of the 'entry' module.
Signed-off-by: Simon Glass <sjg@chromium.org>
The tests were broken by two separate commits which adjusted the output
when boards are listed. Fix this by adding back a PowerPC board and
putting the name of each board in the test.
Fixes: b9f7d881 (powerpc, 5xx: remove some "5xx" remains)
Fixes: 8d7523c5 (buildman: Allow showing the list of boards with -n)
Signed-off-by: Simon Glass <sjg@chromium.org>
Accessing the network slows down the test and limits the environment in
which it can be run. Add an option to disable network tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these tests use the same filename as patman. This adds
confusion when running all tests, since error messages look very similar.
In fact binman tries to run the wrong tests at present.
Rename the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
These test programs are includedd as binary files in U-Boot to avoid
having to build them (and associated toolchain differences). Instructions
on building are in the files themselves, but it seems better to provide
a Makefile which can be manually run when desired.
Add a Makefile, separate from the normal build system, to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a debugging option in the Makefile to allow people to figure out
which u-boot.dtsi files are used in the build. But is it not easy to use
since it only shows files it finds, not those it is looking for. Update it
and update the mention of it to the docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
With all targets converted to generate prepadded images, this removes
the spl_boot0 field from our config structure and removes the unused
code-path (for images that are not prepadded): i.e. spl_boot0 is now
implied as 'true' and the code is specialised by removing the other
case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the spl_boot0 in SPL and use the pre-padding TAG memory,
the mkimage do not need to pad it but only need to replace the value
with correct TAG value.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Prior to this commit, tools/Makefile pulls all libfdt files from
lib/libfdt.
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
This commit changes them to #include ones from scripts/dtc/libfdt.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
I did not touch them in order to avoid unpredictable impact.
The fdt_region.c is U-Boot own file. This is also borrowed from
lib/libfdt/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The pylibfdt is used by dtoc (and, indirectly by binman), but there
is no reason why it must be generated in the tools/ directory.
Recently, U-Boot switched over to the bundled DTC, and the directory
structure under scripts/dtc/ now mirrors the upstream DTC project.
So, scripts/dtc/pylibfdt is the best location.
I also rewrote the Makefile in a cleaner Kbuild style.
The scripts from the upstream have been moved as follows:
lib/libfdt/pylibfdt/setup.py -> scripts/dtc/pylibfdt/setup.py
lib/libfdt/pylibfdt/libfdt.i -> scripts/dtc/pylibfdt/libfdt.i_shipped
The .i_shipped is coped to .i during building because the .i must be
located in the objtree when we build it out of tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
This function is called when signing configuration nodes. Adjust
the error message.
I do not know why we do not need to show the error message in case of
ENOSPC. Remove the if-conditional that seems unnecessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If -K option is missing when you sign image nodes, it fails with
an unclear error message:
tools/mkimage Can't add hashes to FIT blob: -1
It is hard to figure out the cause of the failure.
In contrast, when you sign configuration nodes, -K is optional because
fit_config_process_sig() returns successfully if keydest is unset.
Probably this is a preferred behavior when you want to update FIT with
the same key; you do not have to update the public key in this case.
So, this commit changes fit_image_process_sig() to continue signing
without keydest. If ->add_verify_data() fails, show a clearer error
message, which has been borrowed from fit_config_process_sig().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "algo_name" points to a property in a blob being edited. The
pointer becomes stale when fit_image_write_sig() inserts signatures.
Then crypto->add_verify_data() writes wrong data to the public key
destination.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The fw_env utility family has a default environment compiled in
which ties it quite strongly to the U-Boot source/config it has
been built with. Allow to display the U-Boot version it has been
built with using the -v/--version argument.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Both "conf_name" and "sig_name" point to the name of config node.
The latter should be the name of the signature node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Last user of this option went away in commit:
fdc7718999 ("board: usb_a9263: Update to support DT and DM")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
All BMP files were being treated as though they had a 40 byte header.
There are several BMP header formats consisting of additional data.
This was causing some of the header to be read as color information,
skewing the color palette.
Signed-off-by: Jon Smith <jtsmith@pdiarm.com>
fit_handle_file function does not quote input and output files while preparing
command to run DTC to convert .its to .itb. This results in a failure if input
or output files contain spaces in their names. Quote input and output files in
DTC command to avoid this failure.
Signed-off-by: Mirza, Taimoor <Taimoor_Mirza@mentor.com>
Move the % arch outside the double quote so that the missing toolchain
message is displayed correctly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The recent changes to these files did not completely fix the previous
issues, or introduced different (minor) issues. In cmd/gpt.c we need to
dereference str_disk_guid to be sure that malloc worked. In
cmd/nvedit.c we need to be careful that we can also fit in that leading
space when adding to the string. And in tools/fit_image.c we need to
re-work the error handling slightly in fit_import_data() so that we only
call munmap() once. We have two error paths here, one where we have an
fd to close and one where we do not. Adjust labels to match this.
Reported-by: Coverity (CID: 167366, 167367, 167370)
Signed-off-by: Tom Rini <trini@konsulko.com>
Coverity has found some problems with the return paths in parts of this
code. We have a case where we were going to the wrong part of the
unwind (open() failed so we cannot close the fd), a case where we were
only free()ing our buf on the error path and finally a case where we did
not munmap in the failure path.
Reported-by: Coverity (CID: 138492, 138495, 143064)
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for rk3128 package header in mkimage tool.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Corresponds to 375506d (File writing nit) from upstream
(https://github.com/ulfalizer/Kconfiglib).
Adds proper 'imply' support and fixes a few minor issues, one of which
previously triggered the following weird warning:
configs/taurus_defconfig: /tmp/tmpisI45S:6: warning: assignment to SPL_LDSCRIPT changes mode of containing choice from "arch/$(ARCH)/cpu/u-boot-spl.lds" to "y"
The change in 8639f69 (genconfig.py: Print defconfig next to warnings)
was reapplied.
tools/moveconfig.py previously depended on a hack that merged 'select's
with 'imply's. It was modified to look at the union of
Symbol.get_selected_symbols() and Symbol.get_implied_symbols(), which
should give the same behavior.
tools/genboardscfg.py was verified to produce identical board.cfg's
before and after the change.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
In some cases, such as FreeBSD, the path to an alternative dtc needs to
be used. Rather than override the one given in the Makefile on the
command line, make this part of the build configuration.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a header that indicates that the files generated by dtoc should not be
modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
At present dtoc has a very simplistic view of phandles. It assumes that
a property has only a single phandle with a single argument (i.e. two
cells per property).
This is not true in many cases. Enhance the implementation to scan all
phandles in a property and to use the correct number of arguments (which
can be 0, 1, 2 or more) when generating the C code. For the struct
definitions, use a struct which can hold the maximum number of arguments
used by the property.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
We want to support more than one phandle argument. It makes sense to use
an array for this rather than discrete struct members. Adjust the code to
support this. Rename the member to 'arg' instead of 'id'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
When writing values from properties which contain phandles, dtoc currently
writes 8 phandles per line. Change this to write one phandle per line.
This helps reduce line length, since phandles are generally longer and may
have arguments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
